J2S1-6780-03ENZ2(A)
Before using this online manual Preface Chapter 1 Product Outline 1.1 Multipath Function 1.1.1 Multipath method 1.1.2 Multilink Ethernet method 1.2 Benefits Chapter 2 Capabilities 2.1 Outline of Functions 2.1.1 Fault monitoring system 2.1.2 Switching function 2.1.3 Reachable remote device 2.2 Notes 2.2.1 Notes on installation 2.2.2 Notes on defining the high-layer protocol environment 2.2.3 Notes on operation Chapter 3 Configuration 3.1 Environmental Configuration 3.2 /etc/opt/FJSVmpnet/conf/config 3.3 /etc/opt/FJSVmpnet/conf/parameters 3.4 /etc/opt/FJSVmpnet/conf/hosts 3.5 /etc/opt/FJSVmpnet/conf/hosts6 3.6 /etc/opt/FJSVmpnet/conf/hostname 3.7 /etc/opt/FJSVmpnet/conf/hostname6 Chapter 4 Operation 4.1 Start and Stop of Multipath Function 4.1.1 Starting Multipath Function 4.1.2 Stopping Multipath Function 4.2 To Display MAC Address Used 4.3 Multipath Control 4.4 Start and Stop of TCP/IP Interface 4.4.1 Starting IPv4 interface 4.4.2 Stopping IPv4 interface 4.4.3 Starting IPv6 interface 4.4.4 Stopping IPv6 interface 4.5 To Display the Amount of the Transmission Data 4.6 To Display the Connection State of Transmission Path Chapter 5 Maintenance 5.1 Gathering Information at Fault Occurrence 5.2 Online Trace 5.2.1 Starting of trace 5.2.2 Stopping of trace 5.2.3 Output of driver trace Chapter 6 Command Reference 6.1 MPNET Activation and Deactivation Commands 6.1.1 mpnetinit command 6.1.2 mpnetconfig command 6.2 MAC Address Display Command 6.2.1 mpnet_getmac command 6.3 Multipath Control Command 6.3.1 iompadm command 6.3.2 iompadm subcommands 6.4 TCP/IP Interface Activation and Deactivation Commands 6.4.1 mpnet_ifinit command 6.4.2 mpnet_ifconfig command 6.4.3 mpnet_ifinit6 command 6.4.4 mpnet_ifconfig6 command 6.5 Cluster Administration Commands 6.5.1 mpnet_addrid 6.5.2 mpnet_delrid 6.5.3 mpnet_rid 6.5.4 mpnet_copyfile 6.6 Display Command of the Amount of the Transmission Data 6.6.1 mpnetstat command 6.7 Display Command of the State of Transmission Path 6.7.1 mpnetlinkwatch command Chapter 7 Administration on a Cluster System 7.1 The Correspondence Outline in a Cluster System 7.1.1 Standby mode 7.1.2 Mutual standby mode 7.1.3 Notes 7.2 The environmental configuration on PRIMECLUSTER 7.2.1 Adding the Cluster Environmental Configuration 7.2.2 Deleting the Cluster Environmental Configuration Chapter 8 Dynamic Reconfiguration Function 8.1 Dynamic Reconfiguration function 8.1.1 Dynamic Reconfiguration function for the Multipath function 8.1.2 Environmental Construction 8.1.3 Operation when DR command is executed 8.1.4 Display messages 8.1.5 Reply file 8.2 PCI Hot Plug function 8.2.1 PCI Hot Plug function for the Multipath Function 8.2.2 The Procedure of the PCI Hot Plug function Appendix A Messages A.1 MPNET Driver Messages A.2 MPNET Monitoring Daemon Messages A.3 Activation Command Messages A.3.1 mpnetinit Command Messages A.3.2 mpnetconfig Command Messages A.4 iompadm Command Messages A.5 mpnetstat Command Messages A.6 mpnetlinkwatch Command Messages Appendix B Line Monitoring Daemon B.1 Line Monitoring Daemon B.1.1 Fault Monitoring B.1.2 Switching Time B.1.3 Detectable Failures B.1.4 Monitoring Start/Stop Timing B.2 Configuration of the Line Monitoring Daemon B.2.1 /opt/FJSVmpnet/daemon/mpnetpolld.conf B.2.2 /etc/opt/FJSVmpnet/conf/switch.conf B.3 Adding/Deleting the Communication Path B.3.1 mpnetudtbl command B.4 Messages of the Line Monitoring Daemon