PRIMECLUSTER Installation and Administration Guide 4.1 (for Solaris(TM) Operating System)

6.5 Setting Up Online/Offline Scripts

Create Online and Offline scripts to start and stop ISV applications and user applications in line with the userApplication state transition.

Set the created scripts as Cmdline resources and set those resources in userApplication.

For details, see "Creating Cmdline Resources."

An Online script is started when userApplication is switched to Online.
An Offline script is started when userApplication is switched to Offline.
A Check script is used to monitor the state of the resource that is started or stopped with an Online or Offline script.

This section presents script examples and describes notes on script creation.

Sample scripts

This section shows samples of the Online and Offline scripts, which are set as Cmdline resources.

[Start script/Stop script]

The above script sample is both for the Start script and Stop script.

An example of Check script is shown below:

[Check script]

Set up the above scripts in the Cmdline resource as shown below:

• Start script $FULL_PATH/Script.sample -c
• Stop script $FULL_PATH/Script.sample -u
• Check script $FULL_PATH/Script.sample.check

For information on how to set up these scripts, see "Creating Cmdline Resources."

Notes on script creation

Hot-standby operation

To enable hot-standby operation of the Cmdline resources, the following must be prepared:

• Online/Offline/Check scripts that support hot-standby operation.
• The setting of attributes for the Cmdline resources

1. Create the Online, Offline, and Check scripts to support hot-standby operation. The sample scripts are shown below.

   [Start script/Stop script (hot-standby operation)]

   

   The following example shows Check script that supports hot-standby operation.

   [Check script (hot-standby operation)]

   

2. Setting attributes for the Cmdline resources

   Enable the STANDBYCAPABLE and the ALLEXITCODES attributes.

   For details, see "Creating Cmdline Resources."

Online/Offline script exit code

The state transition process of userApplication changes according to the exit code of the Online/Offline script:

0: Normal exit

The system assumes that the state transition of the Cmdline resource was processed normally, and state transition processing of the userApplication continues. If all the resources of the userApplication are processed normally, the state transition of the userApplication is also processed normally.

Other than 0: Abnormal exit

The system assumes that an error occurred during the state transition of the Cmdline resources and interrupts state transition processing of the userApplication.

Check script exit code

The state of the Cmdline resource is determined by the exit code of Check script. The exit code and the Cmdline resource are associated each other as follows:

0: Indicates the Online state.

Other than 0: Indicates the Offline state.

When ALLEXITCODES variables of the Cmdline resources are enabled, Check script will provide more detailed state of the resource. The exit code and Cmdline resource are associated each other as follows:

0: Indicates the Online state.

1: Indicates the Offline state.

2: Indicates the Faulted state.

3: Indicates the Unknown state.

4: Indicates the Standby state.

For details, see "HELP."

Timeout

If script processing is not completed within the specified time, a timeout occurs, script processing is interrupted by the SIGTERM signal, and state transition ends with an error.

Default: 300 seconds

The timeout value can be specified with the TIMEOUT flag value of the Cmdline resources.

When creating the Cmdline resource, you need to set up a timeout value in "Setting up Cmdline Flags" of "Creating Cmdline Resources." If a timeout occurs when a Cmdline resource is used, change the timeout value to an appropriate value according to the instructions in "Changing Resources."

Environment variables

When the script is executed, the environment variables shown in the table below are set.

Environment variable	Outline
HV_APPLICATION	This variable sets the userApplication name that the resource belongs to. Example) app1
HV_AUTORECOVER	This variable sets the AUTORECOVER value. For details on AUTORECOVER, see "Setting up Cmdline flags" in "Creating Cmdline Resources." 0: No is set. 1: Yes is set.
HV_FORCED_REQUEST	This variable sets a value that indicates whether or not forced failover was requested by operator intervention. 0: Forced failover was not requested. 1: Forced failover was requested.
HV_NODENAME	This variable contains the resource name. Example) Cmdline0
HV_OFFLINE_REASON	This variable sets the trigger for bringing the resource Offline. SWITCH: The resource was set to Offline because of a userApplication switchover request (hvswitch). STOP: The resource was set to Offline because of a userApplication stop request (hvutil -f) FAULT: The resource was set to Offline because of a resource fault. DEACT: The resource was set to Offline because of a userApplication deactivate request (hvutil -d) SHUT: The resource was set to Offline because of an RMS stop request (hvshut)
HV_SCRIPT_TYPE	This variable sets the type of script that was executed. Online: Online script Offline: Offline script
HV_LAST_DET_REPORT	This variable sets the state of the current resources. Online: Online state Offline: Offline state Standby: Standby state Faulted: Faulted state Warning: Warning state
HV_INTENDED_STATE	This variable sets the resource state that is expected after state transition is completed. Online: Online state Offline: Offline state Standby: Standby state Faulted: Faulted state Warning: Warning state
NODE_SCRIPTS_TIME_OUT	This variable sets the timeout duration (seconds) of the script. Example) 300

RMS also has other environment variables. For information on the other environment variables, see the files below.

File Names	Contents
hvenv	Environment variable file to be defined in the entire cluster system
hvenv.local	Environment variable file to be defined only in that node

• For details on the RMS environment variable files (hvenv and hvenv.local), see "2.9 Environment Variables" in the "PRIMECLUSTER Reliant Monitor Service (RMS) with Wizard Tools Configuration and Administration Guide."
• For details on the RMS environment variables, see "10 Appendix - Environment Variables" in the "PRIMECLUSTER Reliant Monitor Service (RMS) with Wizard Tools Configuration and Administration Guide."