The following values are used in the description:
Value | Description |
|---|---|
$INS_DIR | "Program Directory" specified at the AdvancedCopy Manager CCM installation. |
Point
It is recommended that you back up the system before starting the upgrade. If a failure occurs during the upgrade, you cannot restore the environment to the pre-installation status (rollback).
When returning back to the state before installation of the upgrade, recover (restore) the system from the backup.
Log on to the server using Administrator privileges.
Insert the DVD "ETERNUS SF SC/ACM/Express Mediapack for Windows (V16.9 or higher) Manager Program (1/2)" of this version into the DVD drive.
On the secondary node, execute the following batch file and then confirm the output message.
dvdDrive:\Manager_windows\vuptools\esfccm_vlup_first.batIf the following message is output, the setting has been changed for the Upgrade Installation. To reflect the setting, restart the secondary node where the work has been performed. After the secondary node restarts, proceed to the next step.
[Info] Configuration check and change succeeded. You must restart your system before the installation.
If the following message is output, the Upgrade Installation can be performed with the existing setting. Proceed to the next step.
[Info] Configuration check succeeded.
On the primary node, execute the following batch file and then confirm the output message.
dvdDrive:\Manager_windows\vuptools\esfccm_vlup_first.batIf the following message is output, the setting has been changed for the Upgrade Installation. To reflect the setting, restart the primary node where the work has been performed. After the primary node restarts, proceed to the next step.
[Info] Configuration check and change succeeded. You must restart your system before the installation.
If the following message is output, the Upgrade Installation can be performed with the existing setting. Proceed to the next step.
[Info] Configuration check succeeded.
Check that the CCM Server transactions are stopped on the secondary node.
If not stopped, use the Failover Cluster Manager on the secondary node to stop the transactions of AdvancedCopy Manager Copy Control Module.
Stop the CCM Server transactions on the primary node.
Use the Failover Cluster Manager to stop the transactions of AdvancedCopy Manager Copy Control Module.
However, the shared disk for shared data of AdvancedCopy Manager Copy Control Module must be online.
On the primary node, perform a backup of the operating environment of the previous version of the AdvancedCopy Manager Copy Control Module.
Note that the capacity required for performing this backup is 100 MB.
Log on to the server using Administrator privileges.
If already logged on as the Administrator privileges, this step is unnecessary.
Insert the DVD "ETERNUS SF SC/ACM/Express Mediapack for Windows (V16.9 or higher) Manager Program (1/2)" of this version into the DVD drive.
Execute the following batch file to perform a backup of the previous version.
For backupDir, specify the directory in which to store the backup data with an absolute path.
dvdDrive:\Manager_windows\vuptools\esfccmpreinst_cluster.bat backupDir -primary
When the backup fails, after confirming the output error message and removing the cause of the failure, re-execute the batch file.
Point
Spaces and the characters " | : * ? / . < > , % & ^ = ! ; ( ) are not supported for directory name.
The number of characters in a directory name must be up to 220.
Eject the DVD media.
Checking for available disk space
Ensure that there is enough available disk space on the server where the upgrade is performed.
The required disk space for the upgrade is calculated as the "Required Disk Space for New Version" minus the "Required Disk Space for Previous Version".
The space required to install this version of the ETERNUS SF Manager or AdvancedCopy Manager Copy Control Module. Refer to the following locations in the Installation and Setup Guide for this version for information on the required disk space.
For using the AdvancedCopy Manager Copy Control Module in ETERNUS SF Manager
"Operating Environment of ETERNUS SF Manager"
For installing the AdvancedCopy Manager Copy Control Module
"Operating Environment of AdvancedCopy Manager CCM"
The space required to install previous version of the ETERNUS SF Manager or AdvancedCopy Manager Copy Control Module. Refer to the following locations in the Installation and Setup Guide for the relevant previous version for information on the required disk space.
When using the AdvancedCopy Manager Copy Control Module included in the ETERNUS SF Manager Program
"Operating environment of the ETERNUS SF Manage"
When installing and using the AdvancedCopy Manager Copy Control Module Program
"Operating environment of the AdvancedCopy Manager CCM"
On the secondary node, perform a backup of the operating environment of the previous version of the AdvancedCopy Manager Copy Control Module.
The capacity required for performing this backup is 10 MB.
Log on to the server using Administrator privileges.
If already logged on as the Administrator privileges, this step is unnecessary.
Insert the DVD "ETERNUS SF SC/ACM/Express Mediapack for Windows (V16.9 or higher) Manager Program (1/2)" of this version into the DVD drive.
Execute the following batch file to perform a backup of the previous version.
For backupDir, specify the directory in which to store the backup data with an absolute path.
dvdDrive:\Manager_windows\vuptools\esfccmpreinst_cluster.bat backupDir -secondary
When the backup fails, after confirming the output error message and removing the cause of the failure, re-execute the batch file.
Point
Spaces and the characters " | : * ? / . < > , % & ^ = ! ; ( ) are not supported for directory name.
The number of characters in a directory name must be up to 220.
Eject the DVD media.
Checking for available disk space
Ensure that there is enough available disk space on the server where the upgrade is performed.
The required disk space for the upgrade is calculated as the "Required Disk Space for New Version" minus the "Required Disk Space for Previous Version".
The space required to install this version of the ETERNUS SF Manager or AdvancedCopy Manager Copy Control Module. Refer to the following locations in the Installation and Setup Guide for this version for information on the required disk space.
For using the AdvancedCopy Manager Copy Control Module in ETERNUS SF Manager
"Operating Environment of ETERNUS SF Manager"
For installing the AdvancedCopy Manager Copy Control Module
"Operating Environment of AdvancedCopy Manager CCM"
The space required to install previous version of the ETERNUS SF Manager or AdvancedCopy Manager Copy Control Module. Refer to the following locations in the Installation and Setup Guide for the relevant previous version for information on the required disk space.
For using the AdvancedCopy Manager Copy Control Module included in the ETERNUS SF Manager Program
"Operating environment of the ETERNUS SF Manager"
For installing and using the AdvancedCopy Manager Copy Control Module Program
"Operating environment of the AdvancedCopy Manager CCM"
Performing the cluster unsetup
See
Refer to "Deletion of Cluster Environments for CCM Server Transactions" in the Cluster Environment Setup Guide for the previous version for information.
Refer to "C.5 Procedures for Upgrade Installation of AdvancedCopy Manager Copy Control Module Version 15.x (for Windows)" to perform the upgrade.
Information
When the Upgrade Installation terminates in an error, perform recovery by following the steps outlined below.
Install the target version.
If the installation is successfully completed, continue from "6.6.2.3 Performing Upgrade (Secondary Node)".
Perform the upgrade for the secondary node.
The upgrade procedure is the same as that for the primary node. Refer to "6.6.2.2 Performing Upgrade (Primary Node)".
Information
When the Upgrade Installation terminates in an error, perform recovery by following the steps outlined below.
Install the target version.
If the installation is successfully completed, continue from the following tasks.
After upgrading on the primary node and the secondary node, perform the cluster setup. Refer to "Preparations for Customizing CCM Server Transactions" and "Customization for CCM Server Transactions" in the Cluster Environment Setup Guide for this version.
The tasks below need to be performed on the primary node.
Stop the CCM Server transactions
Use the Failover Cluster Manager to stop the transactions to which the AdvancedCopy Manager CCM.
However, the shared disk for shared data of the AdvancedCopy Manager CCM must be online.
Restore the operation environment of the previous version of the AdvancedCopy Manager Copy Control Module.
Note that if step a and step b have already been performed, perform from step c.
Log on to the server using Administrator privileges.
Insert the DVD "ETERNUS SF SC/ACM/Express Mediapack for Windows (V16.9 or higher) Manager Program (1/2)" of this version into the DVD drive.
Execute the following batch file to perform a restore of the previous version.
For backupDir, specify the directory in which the backup data is stored with an absolute path.
dvdDrive:\Manager_windows\vuptools\esfccmpostinst_cluster.bat backupDir -primary
When the restore fails, after confirming the output error message and removing the cause of the failure, re-execute the batch file.
Point
Spaces and the characters " | : * ? / . < > , % & ^ = ! ; ( ) are not supported for directory name.
The number of characters in a directory name must be up to 220.
Eject the DVD media.
The tasks below need to be performed on the secondary node.
Check that the CCM Server transactions are stopped.
If not stopped, use the Failover Cluster Manager to stop the transactions to which the AdvancedCopy Manager CCM belongs.
Restore the operation environment of the previous version of the AdvancedCopy Manager Copy Control Module.
Note that if step a and step b have already been performed, perform from step c.
Log on to the server using Administrator privileges.
Insert the DVD "ETERNUS SF SC/ACM/Express Mediapack for Windows (V16.9 or higher) Manager Program (1/2)" of this version into the DVD drive.
Execute the following batch file to perform a restore of the previous version.
For backupDir, specify the directory in which the backup data is stored with an absolute path.
dvdDrive:\Manager_windows\vuptools\esfccmpostinst_cluster.bat backupDir -secondary
When the restore fails, after confirming the output error message and removing the cause of the failure, re-execute the batch file.
Point
Spaces and the characters " | : * ? / . < > , % & ^ = ! ; ( ) are not supported for directory name.
The number of characters in a directory name must be up to 220.
Eject the DVD media.
Start the CCM Server transactions.
Use the Failover Cluster Manager on the primary node to start the transactions of AdvancedCopy Manager CCM.
Point
Once normal operation has been confirmed after the upgrade, the backup data in the backup destination directory created in step 4-c and step 6-c of "6.6.2.1 Preparing for Upgrade" maybe deleted.