Point
It is recommended that you back up the system before starting the upgrade. If a failure occurs during the upgrade, you cannot restore the environment to the pre-installation status (rollback).
When returning back to the state before installation of the upgrade, recover (restore) the system from the backup.
Check and change the previous version setting with the following procedure.
Log on to the server using Administrator privileges.
Insert the DVD "ETERNUS SF SC/ACM/Express Mediapack for Windows (V16.9 or higher) Manager Program (1/2)" of this version into the DVD drive.
Execute the following batch file and then confirm the output message.
dvdDrive:\Manager_windows\vuptools\esfccm_vlup_first.batIf the following message is output, the setting has been changed for the Upgrade Installation. To reflect the setting, restart the server where the work has been performed. After the server restarts, perform the work in the next section.
[Info] Configuration check and change succeeded. You must restart your system before the installation.
If the following message is output, the Upgrade Installation can be performed with the existing setting. Perform the work in the next section.
[Info] Configuration check succeeded.
With the following procedure, back up the operation environment of the previous version of the AdvancedCopy Manager Copy Control Module.
Note that the capacity required for performing this backup is 100 MB.
Point
It is recommended that you back up the system before starting the upgrade. If a failure occurs during the upgrade, you cannot restore the environment to the pre-installation status (rollback).
When returning back to the state before installation of the upgrade, recover (restore) the system from the backup.
Log on to the server using Administrator privileges.
Insert the DVD "ETERNUS SF SC/ACM/Express Mediapack for Windows (V16.9 or higher) Manager Program (1/2)" of this version into the DVD drive.
Execute the following batch file to perform a backup of the previous version.
For backupDir, specify the directory in which to store the backup data with an absolute path.
dvdDrive:\Manager_windows\vuptools\esfccmpreinst.bat backupDir
When the backup fails, after confirming the output error message and removing the cause of the failure, re-execute the batch file.
Point
Spaces and the characters " | : * ? / . < > , % & ^ = ! ; ( ) are not supported for directory name.
The number of characters in a directory name must be up to 220.
Ensure that there is enough available disk space on the server where the upgrade is performed.
The required disk space for the upgrade is calculated as the "Required Disk Space for New Version" minus the "Required Disk Space for Previous Version".
The space required to install this version of the ETERNUS SF Manager or AdvancedCopy Manager Copy Control Module. Refer to the following locations in the Installation and Setup Guide for this version for information on the required disk space.
For using the AdvancedCopy Manager Copy Control Module in ETERNUS SF Manager:
"Operating Environment of ETERNUS SF Manager"
For installing the AdvancedCopy Manager Copy Control Module:
"Operating Environment of AdvancedCopy Manager CCM"
The space required to install previous version of the ETERNUS SF Manager or the AdvancedCopy Manager Copy Control Module. Refer to the following locations in the Installation and Setup Guide for the relevant previous version for information on the required disk space.
When using the AdvancedCopy Manager Copy Control Module included in the ETERNUS SF Manager Program
"Operating environment of the ETERNUS SF Manager"
When installing and using the AdvancedCopy Manager Copy Control Module Program
"Operating environment of the AdvancedCopy Manager CCM"
Refer to "C.5 Procedures for Upgrade Installation of AdvancedCopy Manager Copy Control Module Version 15.x (for Windows)" to perform the upgrade.
Information
When the Upgrade Installation terminates in an error, perform recovery by following the steps outlined below.
Install the target version.
If the installation is successfully completed, continue from "6.6.1.3 Tasks to Be Performed After Upgrade".
With the following procedure, restore the operation environment of the previous version of the AdvancedCopy Manager Copy Control Module. Note that if step 1 and step 2 have already been performed, perform from step 3.
Log on to the server using Administrator privileges.
Insert the DVD "ETERNUS SF SC/ACM/Express Mediapack for Windows (V16.9 or higher) Manager Program (1/2)" of this version into the DVD drive.
Execute the following batch file to perform a restore of the previous version.
For backupDir, specify the directory in which the backup data is stored with an absolute path.
dvdDrive:\Manager_windows\vuptools\esfccmpostinst.bat backupDir
When the restore fails, after confirming the output error message and removing the cause of the failure, re-execute the batch file.
Point
Spaces and the characters " | : * ? / . < > , % & ^ = ! ; ( ) are not supported for directory name.
The number of characters in a directory name must be up to 220.
Eject the DVD media.
Once normal operation has been confirmed after the upgrade, the backup data in the backup destination directory created in step 3 of "6.6.1.1.2 Backing Up Environment Setting Files" maybe deleted.