This section describes the operation before performing the Live Migration in an Oracle VM Server for SPARC Environment.
Note
Create a /etc/opt/FJSVcluster/etc/clovmmigrate.conf file on all the nodes beforehand. For details, see "17.2.3 Performing Live Migration of the Cluster on the Guest Domains."
Make sure that following items are consistent on all control domains of the target clusters: a combination of a user name and password for the XSCF that is registered in the shutdown facility, and the connection method to the XSCF.
Check that the following settings have been performed for the destination servers:
Before performing this operation, make sure that all target cluster nodes between the guest domains work normally.
If you perform this operation, a cluster system will not be switched until "17.3.3.2 Operation after Performing Live Migration" is completed.
After performing this operation, make sure to perform "17.3.3.2 Operation after Performing Live Migration" even though you cancel the Live Migration.
After performing this operation, make sure to perform "17.3.3.2 Operation after Performing Live Migration" even though the Live Migration failed.
Do not perform the Live Migration during a cluster system switchover.
Changing the cluster configuration (guest domain)
Change the cluster configuration before performing the Live Migration.
Execute the following command on one of the cluster nodes of the guest domain.
# /etc/opt/FJSVcluster/bin/clovmmigrate -pIf you execute this command, the following cluster configurations are changed on all the nodes:
The timeout value of the CF cluster interconnect (current setting value [default 10 seconds] to 600 seconds)
Stopping the shutdown facility
This section describes the operation after performing the Live Migration.
Note
After performing "17.3.3.1 Operation before Performing Live Migration," perform this operation even though you cancel the Live Migration.
After performing "17.3.3.1 Operation before Performing Live Migration," perform this operation even though the Live Migration failed.
A cluster system will not be switched until this operation is completed.
Perform steps 1 and 2 on a control domain.
Perform steps 3 and 4 on a guest domain.
Saving the logical domains configuration information on the source control domain (control domain)
On the source control domain, save the logical domains configuration information.
This operation must be done on the source control domain.
For details, see "Fujitsu SPARC M12 and Fujitsu M10/SPARC M10 System Operation and Administration Guide."
Saving the logical domains configuration information on the destination control domain (control domain)
On the destination control domain, save the logical domains configuration information.
This operation must be done on the source control domain.
For details, see "Fujitsu SPARC M12 and Fujitsu M10/SPARC M10 System Operation and Administration Guide."
Changing the cluster configuration (guest domain)
Change the cluster configuration after performing the Live Migration.
Execute the following command on one of the cluster nodes.
# /etc/opt/FJSVcluster/bin/clovmmigrate -u source-ldom target-host
The target guest domain name to be migrated
The IP address of the destination control domain or the host name registered in the /etc/inet/hosts file
Even if a guest domain is not migrated by such as cancelling the Migration, you need to specify a control domain. To do so, specify the IP address of the source control domain or the host name registered in the /etc/inet/hosts file.
If you execute this command, the following cluster configurations are changed on all the nodes:
The timeout value of the CF cluster interconnect (600 seconds to the setting value before Migration [default 10 seconds])
Change the setting of the shutdown facility (IP address of XSCF-LAN#0, IP address of XSCF-LAN#1, and the SF weight)
Starting the shutdown facility
Checking the state of the shutdown facility (guest domain)
Execute the following commands on each node of a guest domain to check if the cluster is configured correctly after the Live Migration.
# /etc/opt/FJSVcluster/bin/clsnmpsetup -l
# /opt/SMAW/bin/sdtool -s
Note
If TestFailed or InitFailed is displayed, the setting of the shutdown facility could have been unchanged.
If the message 7245 is output in the /var/adm/messages file, the first SSH connection to XSCF has not completed yet. For details, see "PRIMECLUSTER Messages."
For all other circumstances, go back to step 3 and try again.
Example: When the Migration is performed for guest 2 in the two-node cluster between guest domains ("Figure 17.1 Cluster configuration example")
guest2 # /etc/opt/FJSVcluster/bin/clsnmpsetup -l device-name cluster-host-name PPAR-ID domain-name IP-address1 IP-address2 user-name connection-type ------------------------------------------------------------------------------------------------------------------- xscf cfguest1 0 guest1 10.20.30.71 10.20.40.71 xuser ssh xscf cfguest2 1 guest2 10.20.30.73 10.20.40.73 xuser ssh guest2 # ^^ ^^^^^^^^^^^^^^^^^^^^^^^^ guest2 # The target XSCF IP address to be migrated guest2 # The target PPAR-ID to be migrated guest2 # /opt/SMAW/bin/sdtool -s Cluster Host Agent SA State Shut State Test State Init State ------------ ----- -------- ---------- ---------- ---------- cfguest1 SA_xscfsnmpg0p.so Idle Unknown TestWorked InitWorked cfguest1 SA_xscfsnmpg1p.so Idle Unknown TestWorked InitWorked cfguest1 SA_xscfsnmpg0r.so Idle Unknown TestWorked InitWorked cfguest1 SA_xscfsnmpg1r.so Idle Unknown TestWorked InitWorked cfguest2 SA_xscfsnmpg0p.so Idle Unknown TestWorked InitWorked cfguest2 SA_xscfsnmpg1p.so Idle Unknown TestWorked InitWorked cfguest2 SA_xscfsnmpg0r.so Idle Unknown TestWorked InitWorked cfguest2 SA_xscfsnmpg1r.so Idle Unknown TestWorked InitWorked guest2 #
Note
After performing the Live Migration, the following message which indicates the time is not synchronized between the cluster nodes may be printed in the switchlog or /var/adm/messages file.
(WRP, 34) Cluster host <host> is no longer in time sync with local node. Sane operation of RMS can no longer be guaranteed. Further out-of-sync messages will appear in the syslog.
If this situation continues, the following message may be periodically printed in the /var/adm/messages file.
(WRP, 35) Cluster host <host> is no longer in time sync with local node. Sane operation of RMS can no longer be guaranteed.
This message stops once the time is synchronized. For details on the messages, see "PRIMECLUSTER Messages."