The name used to identify a LAN switch blade is displayed.
The name of the device specified as a LAN switch blade is displayed.
The admin port to be used for communication with the admin server is displayed.
The IP address to be used for communication with the admin server is displayed.
For PY CB 10Gb FEX Nexus B22, a hyphen ("-") is displayed.
The product name of a LAN switch blade is displayed.
The model name of a LAN switch blade is displayed.
The serial number of a LAN switch blade is displayed.
The firmware version of a LAN switch blade is displayed.
The status of a LAN switch blade is displayed.
One of the following is displayed:
normal
error
warning
unknown
A slot number representing the mounted location is displayed.
A VCS ID is displayed.
When VCS is not configured, a hyphen ("-") is displayed.
An RBridge ID is displayed.
When VCS is not configured, a hyphen ("-") is displayed.
A Fabric ID is displayed.
When Converged Fabric is not configured, a hyphen ("-") is displayed.
A Domain ID is displayed.
When Converged Fabric is not configured, a hyphen ("-") is displayed.
A Switch ID is displayed.
When Converged Fabric is not configured, a hyphen ("-") is displayed.
Information
When the replacement of a LAN switch blade is completed, "The LAN switch has been replaced. Please confirm that the status of the LAN switch is normal before executing the restore command." is displayed. Perform the restore operation referring to "9.2.5 Replacing Non-server Hardware" in the "Operation Guide CE".
A link to the Web interface of the LAN switch blade is displayed.
Note
If no Web interface is available for the selected LAN switch blade, the following message is displayed: "There is no information to display".
Refer to the LAN switch blade manual to check whether a Web interface is provided.
The number of the port of the selected LAN switch blade is displayed.
The name assigned to the port of the selected LAN switch blade is displayed.
For PY CB 10Gb FEX Nexus B22, internal ports are displayed as 1/1 - 1/16, external ports (from number 1 to 8) are displayed as -/17 - -/24.
The operational status of the port is displayed.
One of the following is displayed:
up
down
unknown
For a LAN switch blade operating in Converged Fabric mode or PY CB 10Gb FEX Nexus B22, a hyphen ("-") is displayed.
The speed and duplex mode of the operating port are displayed.
For a LAN switch blade operating in Converged Fabric mode or PY CB 10Gb FEX Nexus B22, a hyphen ("-") is displayed.
The name of the link aggregation group to which the port of the selected LAN switch blade belongs.
If it does not belong to link aggregation, a hyphen ("-") is displayed.
Information
For LAN switch blade CB Eth Switch 10/40Gb 18/8+2, displayed port information differs depending on the mode.
When using Converged Fabric mode, ports in the range from 1 to 35 are displayed.
When using switch mode and end host mode, ports in the range from 1 to 27 and port 31 are displayed.
The following information is only displayed when LAN switch blades (*) are selected.
The name of the link aggregation group to which the port of the selected LAN switch blade belongs is displayed.
The link aggregation port name is displayed.
LAG/Link aggregation group number
- PY CB Eth Switch/IBP 10Gb 18/8
- PY CB Eth Switch 10/40Gb 18/8+2 (switch mode/end-host mode)
Logical port number of the LAG/port channel
- PY CB Eth Switch/IBP 1Gb 36/8+2
- PY CB Eth Switch/IBP 1Gb 36/12
- PY CB Eth Switch/IBP 1Gb 18/6
The physical port names and the link status (up or down) of the physical ports are displayed for the ports in the link aggregation.
A list of VLAN IDs set in the selected LAN switch blade is displayed.
A list of ports set with a port VLAN ID is displayed.
The logical port for link aggregation is only displayed for LAN switch blades (*).
A list of ports set with tagged VLAN ID(s) is displayed.
The logical port for link aggregation is only displayed for LAN switch blades (*).
* Note: The following LAN switch blades are included:
PY CB Eth Switch/IBP 10Gb 18/8
PY CB Eth Switch 10/40Gb 18/8+2 (switch mode/end-host mode)
PY CB Eth Switch/IBP 1Gb 36/8+2
PY CB Eth Switch/IBP 1Gb 36/12
PY CB Eth Switch/IBP 1Gb 18/6
The following information is only displayed for a LAN switch blade operating in IBP mode.
The name of a port group configured on the selected LAN switch blade is displayed.
The type of this port group is displayed.
One of the following is displayed:
Port Group
VLAN Port Group
Service LAN
Service VLAN
VLAN IDs assigned to this port group are displayed.
The name of the downlink ports assigned to this port group is displayed.
The name of the UplinkSet assigned to this port group is displayed.
The following information is only displayed for a LAN switch blade operating in IBP mode.
The name of an UplinkSet (set of external ports) configured on the selected LAN switch blade is displayed.
The name of the active port within the port backup configuration of this UplinkSet is displayed.
The name of the backup port within the port backup configuration of this UplinkSet is displayed.
Displays whether link state functionality is enabled or not for this UplinkSet.
enable
disable
Displays whether port backup functionality is enabled or not for this UplinkSet.
enable
disable
Displays whether IGMP snooping is enabled or not for this UplinkSet.
enable
disable
Displays whether LACP is enabled or not for this UplinkSet.
enable
disable
The name of the selected LAN switch blade is displayed.
The port name of the LAN switch blade is displayed.
For PY CB 10Gb FEX Nexus B22, internal ports are displayed as 1/1 - 1/16, external ports (from number 1 to 8) are displayed as -/17 - -/24.
The interface name of the resource connected to the LAN switch blade is displayed.
The name of the resource connected to the LAN switch blade is displayed.
Note
Information about connections with network devices is not displayed.
