This section describes the operation before performing the Cold Migration in an Oracle VM Server for SPARC Environment.
Note
The patch for PRIMECLUSTER (T007881SP-02 or later for Solaris 10, or T007882SP-02 or later for Solaris 11) needs to be applied to all cluster nodes.
Prerequisites in "14.2.1 Setting Prerequisites for a Guest Domain on a Control Domain" are required before performing this operation.
Make sure that following items are consistent on all control domains of the target clusters: a combination of a user name and password for the XSCF that is registered in the shutdown facility, and the connection method to the XSCF.
Check that the following settings have been performed for the destination servers:
Before performing this operation, make sure that the target guest domain to be migrated is stopped.
Use the ldm list-domain command to check if STATE is displayed as the bound state.
If the state of STATE is inactive, change its state to bound. The configuration information of the logical domains can be identified by XSCF when the STATE is in the bound state.
Also, make sure that the cluster of the guest domain other than Migration works normally.
If you cancel the Cold Migration after performing this operation, "14.3.2.2 Operation after Performing Cold Migration" is unnecessary.
Changing the cluster configuration (control domain)
Change the cluster configuration before performing the Cold Migration.
Execute the following command on the cluster nodes of the source control domain.
When the guest domain is stopped, the return value of the command is 1.
# /etc/opt/FJSVcluster/bin/clovmmigrate -p source-ldomThe guest domain name to be migrated.
By executing this command, you can check if the guest domain specified for source-ldom is stopped.
This section describes the operation after performing the Cold Migration in an Oracle VM Server for SPARC Environment.
Note
These steps are unnecessary if you cancel the Cold Migration after performing "14.3.2.1 Operation before Performing Cold Migration."
Start this operation before starting a guest domain.
Perform steps 1 through 3 on a control domain.
Perform step 4 on a guest domain.
When performing this operation, the saved configuration information of the logical domains should not be above 6. Execute the following command to check the saved configuration information of the logical domains.
Also, check that "config_tmp" does not exist in the saved configuration information name of the logical domains.
# ldm list-spconfigIf the configuration information of the saved logical domain is 7 or more, execute the following command to delete the configuration information to make them 6 or less.
# ldm remove-spconfig configuration name
If "config_tmp" exists in the configuration name of the logical domain, execute the following command to delete it.
# ldm remove-spconfig config_tmpFor details on the configuration information of the logical domain, see "Operations and Commands Related to Logical Domain Configurations" in "SPARC M10 Systems Domain Configuration Guide."
Changing the cluster configuration (control domain)
Change the cluster configuration after performing the Cold Migration.
Execute the following command on the cluster nodes of the source control domain.
When the guest domain is stopped, the return value of the command is 1.
# /etc/opt/FJSVcluster/bin/clovmmigrate -u source-ldom target-hostThe target guest domain name to be migrated
The host name registered to the IP address or the /etc/inet/hosts file of the destination control domain
If you execute this command, information of the logical domains is saved both by the source control domain and the destination control domain.
Checking the state of the guest domain and saving the configuration information (control domain)
Execute the following command on the destination control domain to check the state of the guest domain that was migrated by the Cold Migration.
# ldm list-domainIf the migrated guest domain is in the bound state, proceed to the following steps.
If the migrated guest domain is in the inactive state, change its state to bound. After changing the state of the guest domain to bound, save the configuration information of the logical domains on the source control domain and the destination control domain. The configuration information of the logical domains can be identified by XSCF when the guest domain is in the bound state. For details, see "SPARC M10 Systems System Operation and Administration Guide."
Starting the guest domain (control domain)
Start the stopped guest domain that was migrated by the Cold Migration.
When the guest domain is started, the following cluster configuration is changed on all nodes of the cluster between guests.
Change the setting of the shutdown facility (IP address of XSCF-LAN#0, IP address of XSCF-LAN#1, and the SF weight)
Checking the state of the shutdown facility (guest domain)
Execute the following commands on each node of a guest domain to check if the cluster is configured correctly after the Cold Migration.
# /etc/opt/FJSVcluster/bin/clsnmpsetup -l
# /opt/SMAW/bin/sdtool -s
Note
If TestFailed or InitFailed is displayed, the setting of the shutdown facility could have been unchanged.
Go back to step 1 and try again.
Example: When the Migration is performed for guest 2 in the two-node cluster between guest domains ("Figure 14.1 Cluster configuration example")
guest2 # /etc/opt/FJSVcluster/bin/clsnmpsetup -l device-name cluster-host-name PPAR-ID domain-name IP-address1 IP-address2 user-name connection-type ------------------------------------------------------------------------------------------------------------------- xscf cfguest1 0 guest1 10.20.30.71 10.20.40.71 xuser ssh xscf cfguest2 1 guest2 10.20.30.73 10.20.40.73 xuser ssh guest2 # ^^ ^^^^^^^^^^^^^^^^^^^^^^^^^^^ guest2 # The target XSCF IP address to be migrated guest2 # The target PPAT-ID to be migrated guest2 # /opt/SMAW/bin/sdtool -s Cluster Host Agent SA State Shut State Test State Init State ------------ ----- -------- ---------- ---------- ---------- cfguest1 SA_xscfsnmpg0p.so Idle Unknown TestWorked InitWorked cfguest1 SA_xscfsnmpg1p.so Idle Unknown TestWorked InitWorked cfguest1 SA_xscfsnmpg0r.so Idle Unknown TestWorked InitWorked cfguest1 SA_xscfsnmpg1r.so Idle Unknown TestWorked InitWorked cfguest2 SA_xscfsnmpg0p.so Idle Unknown TestWorked InitWorked cfguest2 SA_xscfsnmpg1p.so Idle Unknown TestWorked InitWorked cfguest2 SA_xscfsnmpg0r.so Idle Unknown TestWorked InitWorked cfguest2 SA_xscfsnmpg1r.so Idle Unknown TestWorked InitWorked guest2 #