This section explains upgrading of the HBA address rename setup service.
Transferred Data
There is no HBA address rename setup service data to transfer when upgrading from an earlier version to this version.
Preparations
Perform the following preparations and checks before upgrading:
Check that the environment is one in which agents of this version can be operated.
For operating environments, refer to "Chapter 1 Operational Environment".
Upgrade using Upgrade Installation
When upgrading to this version from V2.1.1, upgrade can be performed using upgrade installation. Perform the upgrade using the following procedure:
Note
Do not perform any other operations with Resource Coordinator VE until the upgrade is completed.
Perform upgrading of the HBA address rename setup service after upgrading of managers is completed.
In the event that upgrade installation fails, please resolve the cause of the failure and perform upgrade installation again. If the problem cannot be resolved and upgrade installation fails again, please contact Fujitsu technical staff.
When performing an upgrade installation, please do not access the installation folder of the earlier version or any of the files and folders inside it using the command prompt, Explorer, or an editor.
While it is being accessed, attempts to perform upgrade installation will fail.
If upgrade installation fails, stop accessing the files or folders and then perform the upgrade installation again.
When stopping the upgrade and restoring the earlier version, please re-install the HBA address rename setup service of the earlier version.
When performing restoration and the HBA address rename setup service of this version or an earlier version has been installed, please uninstall it.
Upgrade installation will delete patches that were applied to the earlier version.
[Linux]
When the PATH variable has not been configured to enable execution of UpdateAdvisor (Middleware) commands from a user-defined location, performing uninstallation will delete any patches that have been applied to the earlier version of Resource Coordinator VE, but it will not delete product information or component information. Refer to the UpdateAdvisor (Middleware) manual, delete software and component information from the applied modification check list.
Upgrade Installation
[Windows]
Refer to "2.3.2 Installation [Windows]", and execute the Resource Coordinator VE installer.
The Resource Coordinator VE setup window will be displayed. Check the contents of the license agreement, etc. and then click <Yes>.
The setting information that will be taken over from the earlier version will be displayed. Please check it and then click <Install>. Upgrade installation will begin.
[Linux]
Refer to "2.3.3 Installation [Linux]", and execute the Resource Coordinator VE installer.
The Resource Coordinator VE setup window will be displayed. Check the contents of the license agreement, etc. and then enter "y".
A message checking about performing the upgrade installation will be displayed.
To perform upgrade installation, enter "y". Upgrade installation will begin.
Display the Resource Coordinator VE Setup Completion Window [Windows]
When using the HBA address rename setup service immediately after configuration, check the "Yes, launch it now." checkbox.
Click <Finish> and close the window. If the checkbox was checked, the HBA address rename setup service will be started after the window is closed.
Start the HBA address rename setup Service
[Windows]
When the HBA address rename setup service was not started in step 2., refer to "6.2.2.1 Settings for the HBA address rename setup service" of the "ServerView Resource Coordinator VE Setup Guide", and start the HBA address rename setup service.
[Linux]
Start the HBA address rename setup service referring to the procedure in "6.2.2.1 Settings for the HBA address rename setup service" of the "ServerView Resource Coordinator VE Setup Guide".
Manual Upgrade
Perform upgrading of the V13.2 or V13.3 HBA address rename setup service using the following procedure.
Note
Do not perform any other operations with Resource Coordinator VE until the upgrade is completed.
Perform upgrading of the HBA address rename setup service after upgrading of managers is completed.
Uninstallation of the HBA address rename setup service of the earlier version
Refer to the "Systemwalker Resource Coordinator Virtual server Edition Installation Guide", and uninstall the HBA address rename setup service.
Installation of the HBA address rename setup service of this version
Refer to "2.3.2 Installation [Windows]", and execute the Resource Coordinator VE installer.
Information
The V13.2 HBA address rename setup service is deleted when V13.2 clients are uninstalled. For uninstallation of V13.2 clients , refer to the "Systemwalker Resource Coordinator Virtual server Edition Installation Guide" of V13.2.
For the installation method of the HBA address rename setup service, refer to "2.3 HBA address rename setup service Installation".
For settings for the HBA address rename setup service, refer to "6.2.2.1 Settings for the HBA address rename setup service" of the "ServerView Resource Coordinator VE Setup Guide".
