Procedure to install the Manager is described below.
The CD-ROM "ETERNUS SF Storage Cruiser 14.1 Manager/Agent (Linux, VMware)" is used for installing the Manager.
Check if a local file system is mounted (in the case of a single user mode)
Please install this software in multi-user mode.
When the installation is performed in single-user mode, check whether the local file system is mounted before installation. If it is not mounted, mount the local file system.
# /usr/sbin/mountall -l
See
Refer to operation system manual, for details of mountall command.
Check if basic software is installed
Make sure that the basic software is installed and this software is not installed.
Set up the CD-ROM "ETERNUS SF Storage Cruiser 14.1 Manager/Agent (Linux, VMware)" and then execute the command below:
# cd CD-ROM mount point /manager/RHEL # /bin/sh ./scinstall.sh -check
When a message is displayed after executing the above command, take a relevant measure accordingly.
When basic required software is not installed
Install the required software.
When ETERNUS SF Storage Cruiser Manager is already installed
Refer to "9.2 [Linux] Manager Uninstallation" to stop the Manager, and then uninstall the package displayed.
Note
FJSVswstt is a common package with other products. ETERNUS SF Storage Cruiser uses a preinstalled package so that the software should not be uninstalled.
When SMAWdtcp package, the bundled software of PRIMECLUSTER Enterprise Edition, is installed, SMAWdtcp package must be uninstalled before installing this software. Refer to "PRIMECLUSTER(TM) Enterprise Edition 4.2A30 for Linux(TM) Environment Installation Guide" for how to delete the software.
Installation time for this software is around 10 minutes.
By executing this software's exclusive installation command "scinstall.sh", multiple packages can be installed simultaneously. The scinstall.sh command calls the rpm(8) command and installs the configuration program package.
Login with root (super user).
# su
After performing the procedures in "4.2.3.1 Pre-installation preparation", move to the directory storing scinstall.sh command.
# cd CD-ROM_mount_point/manager/RHEL
Execute the scinstall.sh command.
# /bin/sh ./scinstall.sh
The following message is output. To execute installation enter "y", to discontinue the installation enter a different character.
ETERNUS SF Storage Cruiser 14.1 Copyright FUJITSU LIMITED 2006-2010 This program will install "ETERNUS SF Storage Cruiser" Manager on your system. Do you want to continue the installation of this package? [y, n, ?, q]
When "y" is entered, the installation will commence.
Message examples are as follows:
INFO : Starting Installation of ETERNUS SF Storage Cruiser ... INFO : Package FJSVswstt was successfully installed. INFO : Package FJSVtrccb was successfully installed. : INFO : Package FJSVssmge was successfully installed.
When the installation is completed successfully, the following message will be displayed.
INFO : "ETERNUS SF Storage Cruiser" Manager was installed successfully.
If the installation fails, one of the following messages will be displayed.
ERROR : Required Package_name is not installed. or ERROR : Exclusive package "Software_name" is installed. or ERROR : Package Package_name is already installed. or ERROR : Installing Package_name was failed.
If the installation fails, check the installation status with the following command.
# /bin/sh ./scinstall.sh -check
In cases where the same versions of packages have been installed, delete all packages identified by the above command, using the scuninstall.sh command. Then recommence the installation process from Step 3.
# /bin/sh ./scuninstall.sh
Information
The scuninstall.sh is stored in the same directory as the scinstll.sh command.
When the installation failed even if the above procedure was taken, take note of the message displayed and contact Fujitsu technical engineer.
The installation is completed. Continuously, execute the post-installation setup.
When the operation control server is not a cluster system
Refer to "4.2.4 Post-installation setup" and execute a setup after installation.
When the operation control server is a cluster system
Refer to "A.4 Manager operation setup" and execute a setup in the cluster environment.
