| ETERNUS SF Storage Cruiser User's Guide 13.2 - Solaris (TM) Operating System / Linux / Microsoft(R) Windows(R) - |
|
Contents
Index
|
This chapter explains how to use commands.
This section explains command operations on the Solaris OS Administrative server.
The following sections explain the commands for managing the operating environment.
Function
This command sets administrative login account and perform creation of a CLI encryption key. Only OS administrator (root) user can execute this command. This command only can execute when admin server stop. Refer to "C.1.2.2 Starting and stopping the daemons of the administrative server at specific times" for the detail information.
Use
To create administrator login account.
Format
|
# /opt/FJSVssmgr/bin/scsetup |
Parameter
This command set the parameter by the following interface.
|
Input a new CLI crypt key [length:4-56]: any key Are you sure? [y,n,q?] y Input a new user name [length:1-16]: username Input a new password [length:1-16]: password Retype a new password [length:1-16]: password Are you sure? [y,n,q?] y |
CLI encryption key
Please enter the CLI encryption key to be used (between 4 and 56 characters). Double-byte characters, single-byte alphanumerical characters, symbols, and strings composed entirely of single or double-byte characters can be used. Notice that CLI encryption is required for ETERNUS SF Storage Cruiser internal use only, and users don't have to remember the key.
Username
Enter the user name of the login account for administrators (between 1 and 16 characters). The name must start with an alphabetic character, and alphanumerical characters (including underscores, "_", periods, ""., and hyphens, "-") can be used.
Password
Enter the password of the login account for administrators (between 1 and 16 characters). The password is a string of alphanumerical characters and symbols, but can not start with "{".
Password confirmation
For password confirmation, enter the password of the administrator again.
Examples
|
# /opt/FJSVssmgr/bin/scsetup |
Function
After the IP address of the administrative server is changed, delete the old IP address of the administrative server that is the SNMP Trap transmission place from the devices registered with this software product. and add the new IP address.
Although the SNMP Trap transmission place setting for a device may be changed with the Management Software on the device, this software product provides this command to facilitate changing of the transmission place.
Use
Execute the command after changing the IP address of Manager. The command may be executed for all devices managed by this software product by the one command or for a specific device.
Devices that can be targets of the command are devices for which SNMP Trap transmission place settings can be defined automatically from this software product.
The monitoring status of every target device must be normal.
Format
|
# /opt/FJSVssmgr/bin/sanadmsh chtraprcvip [-h / -all / DeviceID] -oldip xxx.xxx.xxx.xxx (-newip yyy.yyy.yyy.yyy) |
Parameter
-h
Displays Help about the argument format of the chtraprcvip command.
-all
Applies SNMP Trap transmission place setting to all devices managed by this software product. Executing the command specified with this argument outputs device names and execution results in execution order to the standard output. If the administrative server has more than one IP address, for example, if the management server is connected to multiple subnets, a device may not be set with the correct SNMP Trap transmission place. After this setting is performed, check whether the correct administrative server address is set as the SNMP Trap transmission place setting on the device side.
DeviceID
Applies SNMP Trap transmission place setting to the limited devices. Specify the device type according to the following tables. Afterwards, specify how to recognize the device.
|
Device type |
Device recognition method (one of which must be specified) |
|
-host |
ip:xxx.xxx.xxx.xxx sysname: SysName name of a device SNMP setting nickname: Device management name that is set for this software product. |
-oldip xxx.xxx.xxx.xxx
Specify the old IP address of the administrative server. Delete this IP address from the SNMP transmission place address of managed devices.
-newip yyy.yyy.yyy.yyy
Specify the new IP address of the new administrative server. Add this IP address to the SNMP transmission place address. If this argument is omitted, the IP address of the new administrative server is automatically specified. It is recommended to enter the argument considering the administrative server that has multiple IP afddresses.
Examples
Execute the SNMP Trap transmission place change on all managed devices that can automatically execute SNMP Trap transmission place setting.
|
# /opt/FJSVssmgr/bin/sanadmsh chtraprcvip -all -oldip 100.100.100.100 -newip 200.200.200.200 |
Execute the SNMP Trap transmission place change on server nodes that sysname is defined in host1.
|
# /opt/FJSVssmgr/bin/sanadmsh chtraprcvip -host sysname:host1 -oldip 100.100.100.100 -newip 200.200.200.200 |
Function
This command checks whether this software product can receive an SNMP Trap correctly, display an event, and cooperate with Systemwalker Centric Manager and Shell.
A simulated Fibre Channel switch SNMP Trap (FC Port fault) is created and issued to the administrative server.
Use
Execute the command specified with the IP address of a Fibre Channel switch to check the Trap setting of the switch.
The Fibre Channel switch must be a device managed by this software product.
Format
|
# /opt/FJSVssmgr/bin/swtraptest fibre-channel-switch-ip-address |
Parameter
fibre-channel-switch-ip-address
Specify the IP address of the Fibre Channel switch which is to check the SNMP trap setting by this trap test command.
Example
Executing this command for a Fibre Channel switch whose IP address is 11.11.11.11
|
# /opt/FJSVssmgr/bin/swtraptest 11.11.11.11 |
Even the input IP address is not for a FC device, this command can be executed.
In this case, it executes as the event of device which IP address is input.
Function
This command checks whether this software product can receive an SNMP Trap correctly, display an event, and cooperate with Systemwalker Centric Manager and Shell.
The administrative server internally generates pseudo SNMP traps (FAN fault) of the ETERNUS8000, ETERNUS6000, ETERNUS4000, ETERNUS3000, ETERNUS2000 and GR device, and issues them to the administrative server itself.
Use
Execute the command specified with the IP address of a storage device to check the Trap setting of the device.
The storage device must be a device managed by this software product.
Format
|
# /opt/FJSVssmgr/bin/grtraptest storage-ip-address |
Parameter
storage-ip-address
Specify the IP address of the storage which is to check the SNMP trap setting by this trap test command.
Example
Executing the command for a storage device whose IP address is 12.12.12.12
|
# /opt/FJSVssmgr/bin/grtraptest 12.12.12.12 |
Even the input IP address is other than ETERNUS8000, ETERNUS6000, ETERNUS4000, ETERNUS3000, ETERNUS2000, GR series, this command can be executed.
In this case, it executes as the event of device which IP address is input.
Function
This command is used to set/delete/display the storage device host affinity and Fibre Channel switch zoning.
Use
Specify the storage device CA WWPN, affinity group, and WWPN of the set HBA in the command parameter to set/delete the storage device host affinity and Fibre Channel switch zoning. The set host affinity and zoning is also displayed.
The target storage device and Fibre Channel switch must be devices managed by this product.
Format
|
# /opt/FJSVssmgr/sbin/storageadm zone add -storage cawwpn,affinitygroup -hba hbawwpn # /opt/FJSVssmgr/sbin/storageadm zone delete -storage cawwpn,affinitygroup -hba hbawwpn # /opt/FJSVssmgr/sbin/storageadm zone info [-ipaddr ipaddr[,ipaddr,...]] |
Parameter
add
This sets the host affinity and zoning.
delete
This deletes the host affinity and zoning.
info
This displays the host affinity and zoning.
-storage cawwpn,affinitygroup
Specify the storage device CA WWPN and affinity group for which the host affinity is set or deleted.
-hba hbawwpn
Specify the WWPN of the HBA set for host affinity and zoning.
-ipaddr ipaddr[,ipaddr,...]
Displays the host affinity information set in the specified IP address, Fibre Channel switch zoning information, or storage device CA.
To display more than one item of storage device information, specify the IP address using a comma (",").
If this omitted, all the storage device and Fibre Channel switch information registered in this product is displayed.
Examples
Adding the host affinity and zoning
|
# /opt/FJSVssmgr/sbin/storageadm zone add -storage 1111111111111111,3 -hba 2222222222222222 |
Deleting the host affinity and zoning
|
# /opt/FJSVssmgr/sbin/storageadm zone delete -storage 1111111111111111,3 -hba 2222222222222222 |
Displaying the host affinity and zoning
# /opt/FJSVssmgr/sbin/storageadm zone info
<<< FC Switch Zone Information >>>
DEVICE_NAME(IP_ADDRESS) ZONE_NAME ZONE_WWPN
------------------------------ --------------- ---------------------------------
Switch1(10.10.10.10) SNM_0001 1111111111111111;2222222222222222
SNM_0002 3333333333333333;4444444444444444
--------------------------------------------------------------------------------
<<< FC CA Zone Information >>>
DEVICE_NAME(IP_ADDRESS) CA_WWPN AFFINITY_GROUP HBA_WWPN
------------------------------ ---------------- --------------- ----------------
E4000M300(10.10.10.11) 1111111111111111 3 2222222222222222
--------------------------------------------------------------------------------
|
- The storage device and Fibre Channel switch for which set/delete/display is performed must have been registered in this product.
This command cannot be used to register Fibre Channel switches if zoning has not been set. Create a temporary zone and then register the Fibre Channel switch in this product. Refer to "4.2.1.1 Setting" for details on creating a temporary zone..
- Please execute this command after confirming the state of the server is below. (When the server where HBA specified for "-hba" option is installed is registered in this product.)- The server had to have started when "Add" option was specified.- The server had to have stopped when "Delete" option was specified.
- Fibre Channel switch zoning is set for the Fibre Channel switch connected to the specified storage device CA.
- The Fibre Channel switch and storage device must be connected using a Fibre Channel cable. If the Fibre Channel cable is not connected, Fibre Channel switch zoning is not set. Connect the Fibre Channel cable, and then re-execute the command.
- Zone settings (creation of the AffinityGroup) must be configured in the ETERNUS disk array device in advance, using Storage Volume Configuration Navigator or ETERNUSmgr.
- Only the SN200 (except for model 250M) and Brocade (except for AP7420) Fibre Channel switch and PRIMERGY BX600 switchblades are supported.
- The following conformation message is output when 'delete' is specified. To continue, enter 'y'. To cancel, enter 'n'.
Are you sure? [y/n]:
This section explains the commands for starting and stopping daemons.
Starting the SNMP Trap monitoring daemon
Enter the following command to start the SNMP Trap monitoring daemon:
|
# /opt/FJSVswstt/bin/mpnm-trapd start |
Stopping the SNMP Trap monitoring daemon
Enter the following command to stop the SNMP Trap monitoring daemon:
|
# /opt/FJSVswstt/bin/mpnm-trapd stop |
Checking the SNMP Trap monitoring daemon
Enter the following command to confirm if the process exists.
|
# /bin/ps -ef | grep nwsnmp-trapd | grep -v grep |
Start or stop the following daemons in a batch operation:
|
Daemon name |
Admin server daemon SNMP Trap monitoring daemon |
Starting daemons of the administrative server
Enter the following command to start the administrative server:
|
# /opt/FJSVssmgr/sbin/managerctl start |
Stopping daemons of the administrative server
Enter the following command to stop the administrative server:
|
# /opt/FJSVssmgr/sbin/managerctl stop |
In an environment in which the SAN administration manager in SystemWalker/StorageMGR-M V5.1/V10 or Softek SANView4.1 CD-ROM sub-directory is installed, the SNMP Trap monitoring daemon is controlled by SystemWalker/StorageMGR-M (SAN administration manager in Softek SANView4.1 CD-ROM sub-directory), so only the admin server daemon is started and stopped by the above commands.
This section explains the commands for collecting troubleshooting information.
Function
Collect information on the administrative servers.
Use
rcxmgrsnap is the command used to collect information on administrative server when a problem occurs.
Submit the information to Fujitsu technical staff.
Format
|
# /opt/FJSVssmgr/sbin/managersnap [-dir directory] [-all] |
Parameter
No parameter
The troubleshooting information will be stored on /tmp directory.
- dir
Specify the directory where troubleshooting information is to be stored.
-all
Collects all troubleshooting information on servers. Data includes lots of information, which will increase the size of the data. This option is not necessary for initial investigation.
Example
|
# /opt/FJSVssmgr/sbin/managersnap |
This section explains command operations on the Linux Administrative server.
The following sections explain the commands for managing the operating environment.
Function
This command sets administrative login account and perform creation of a CLI encryption key. Only OS administrator (root) user can execute this command. This command only can execute when admin server stop. Refer to "C.2.2.2 Starting and stopping the daemons of the administrative server at specific times" for the detail information.
Use
To create administrator login account.
Format
|
# /opt/FJSVssmgr/bin/scsetup |
Parameter
This command set the parameter by the following interface.
|
Input a new CLI crypt key [length:4-56]: any key Are you sure? [y,n,q?] y Input a new user name [length:1-16]: username Input a new password [length:1-16]: password Retype a new password [length:1-16]: password Are you sure? [y,n,q?] y |
CLI encryption key
Please enter the CLI encryption key to be used (between 4 and 56 characters). Double-byte characters, single-byte alphanumerical characters, symbols, and strings composed entirely of single or double-byte characters can be used. Notice that CLI encryption is required for ETERNUS SF Storage Cruiser internal use only, and users don't have to remember the key.
Username
Enter the user name of the login account for administrators (between 1 and 16 characters). The name must start with an alphabetic character, and alphanumerical characters (including underscores, "_", periods, ".", and hyphens, "-") can be used.
Password
Enter the password of the login account for administrators (between 1 and 16 characters). The password is a string of alphanumerical characters and symbols, but cannot start with "{".
Password confirmation
For password confirmation, enter the password of the administrator again.
Examples
|
# /opt/FJSVssmgr/bin/scsetup |
Function
After the IP address of the administrative server is changed, delete the old IP address of the administrative server that is the SNMP Trap transmission place from the devices registered with this software product, and add the new IP address.
Although the SNMP Trap transmission place setting for a device may be changed with the Management Software on the device, this software product provides this command to facilitate changing of the transmission place.
Use
Execute the command after changing the IP address of Manager. The command may be executed for all devices managed by this software product by the one command or for a specific device.
Devices that can be targets of the command are devices for which SNMP Trap transmission place settings can be defined automatically from this software product.
The monitoring status of every target device must be normal.
Format
|
# /opt/FJSVssmgr/bin/sanadmsh chtraprcvip [-h / -all / DeviceID] -oldip xxx.xxx.xxx.xxx (-newip yyy.yyy.yyy.yyy) |
Parameter
-h
Displays Help about the argument format of the chtraprcvip command.
-all
Applies SNMP Trap transmission place setting to all devices managed by this software product. Executing the command specified with this argument outputs device names and execution results in execution order to the standard output. If the administrative server has more than one IP address, for exsample, if the management server is connected to multiple subnets, a device may not be set with the correct SNMP Trap transmission place. After this setting is performed, check whether the correct administrative server address is set as the SNMP Trap transmission place setting on the device side.
DeviceID
Applies SNMP Trap transmission place setting to the limited devices. Specify the device type according to the following tables. Afterwards, specify how to recognize the device.
|
Device type |
Device recognition method (one of which must be specified) |
|
-host |
ip:xxx.xxx.xxx.xxx sysname: SysName name of a device SNMP setting nickname: Device management name that is set for this software product. |
-oldip xxx.xxx.xxx.xxx
Specify the old IP address of the administrative server. Delete this IP address from the SNMP transmission place address of managed devices.
-newip yyy.yyy.yyy.yyy
Specify the new IP address of the new administrative server. Add this IP address to the SNMP transmission place address. If this argument is omitted, the IP address of the new administrative server is automatically specified. It is recommended to enter the argument considering the administrative server that has multiple IP addresses.
Examples
Execute the SNMP Trap transmission place change on all managed devices that can automatically execute SNMP Trap transmission place setting.
|
# /opt/FJSVssmgr/bin/sanadmsh chtraprcvip -all -oldip 100.100.100.100 -newip 200.200.200.200 |
Execute the SNMP Trap transmission place change on server nodes that sysname is defined in host1.
|
# /opt/FJSVssmgr/bin/sanadmsh chtraprcvip -host sysname:host1 -oldip 100.100.100.100 -newip 200.200.200.200 |
Function
This command checks whether this software product can receive an SNMP Trap correctly, display an event, and cooperate with Systemwalker Centric Manager and Shell.
A simulated Fibre Channel switch SNMP Trap (FC Port fault) is created and issued to the administrative server.
Use
Execute the command specified with the IP address of a Fibre Channel switch to check the Trap setting of the switch.
The Fibre Channel switch must be a device managed by this software product.
Format
|
# /opt/FJSVssmgr/bin/swtraptest fibre-channel-switch-ip-address |
Parameter
fibre-channel-switch-ip-address
Specify the IP address of the Fibre Channel switch which is to check the SNMP trap setting by this trap test command.
Example
Executing this command for a Fibre Channel switch whose IP address is 11.11.11.11
|
# /opt/FJSVssmgr/bin/swtraptest 11.11.11.11 |
Even the input IP address is not for a FC device, this command can be executed.
In this case, it executes as the event of device which IP address is input.
Function
This command checks whether this software product can receive an SNMP Trap correctly, display an event, and cooperate with Systemwalker Centric Manager and Shell.
The administrative server internally generates pseudo SNMP traps (FAN fault) of the ETERNUS8000, ETERNUS6000, ETERNUS4000, ETERNUS3000, ETERNUS2000 and GR device, and issues them to the administrative server itself.
Use
Execute the command specified with the IP address of a storage device to check the Trap setting of the device.
The storage device must be a device managed by this software product.
Format
|
# /opt/FJSVssmgr/bin/grtraptest storage-ip-address |
Parameter
storage-ip-address
Specify the IP address of the storage which is to check the SNMP trap setting by this trap test command.
Example
Executing the command for a storage device whose IP address is 12.12.12.12
|
# /opt/FJSVssmgr/bin/grtraptest 12.12.12.12 |
Even the input IP address is other than ETERNUS8000, ETERNUS6000, ETERNUS4000, ETERNUS3000, ETERNUS2000, GR series, this command can be executed.
In this case, it executes as the event of device which IP address is input.
Function
This command is used to set/delete/display the storage device host affinity and Fibre Channel switch zoning.
Use
Specify the storage device CA WWPN, affinity group, and WWPN of the set HBA in the command parameter to set/delete the storage device host affinity and Fibre Channel switch zoning. The set host affinity and zoning is also displayed.
The target storage device and Fibre Channel switch must be devices managed by this product.
Format
|
# /opt/FJSVssmgr/sbin/storageadm zone add -storage cawwpn,affinitygroup -hba hbawwpn # /opt/FJSVssmgr/sbin/storageadm zone delete -storage cawwpn,affinitygroup -hba hbawwpn # /opt/FJSVssmgr/sbin/storageadm zone info [-ipaddr ipaddr[,ipaddr,...]] |
Parameter
add
This sets the host affinity and zoning.
delete
This deletes the host affinity and zoning.
info
This displays the host affinity and zoning.
-storage cawwpn,affinitygroup
Specify the storage device CA WWPN and affinity group for which the host affinity is set or deleted.
-hba hbawwpn
Specify the WWPN of the HBA set for host affinity and zoning.
-ipaddr ipaddr[,ipaddr,...]
Displays the host affinity information set in the specified IP address, Fibre Channel switch zoning information, or storage device CA.
To display more than one item of storage device information, specify the IP address using a comma (",").
If this omitted, all the storage device and Fibre Channel switch information registered in this product is displayed.
Examples
Adding the host affinity and zoning
|
# /opt/FJSVssmgr/sbin/storageadm zone add -storage 1111111111111111,3 -hba 2222222222222222 |
Deleting the host affinity and zoning
|
# /opt/FJSVssmgr/sbin/storageadm zone delete -storage 1111111111111111,3 -hba 2222222222222222 |
Displaying the host affinity and zoning
# /opt/FJSVssmgr/sbin/storageadm zone info
<<< FC Switch Zone Information >>>
DEVICE_NAME(IP_ADDRESS) ZONE_NAME ZONE_WWPN
------------------------------ --------------- ---------------------------------
Switch1(10.10.10.10) SNM_0001 1111111111111111;2222222222222222
SNM_0002 3333333333333333;4444444444444444
--------------------------------------------------------------------------------
<<< FC CA Zone Information >>>
DEVICE_NAME(IP_ADDRESS) CA_WWPN AFFINITY_GROUP HBA_WWPN
------------------------------ ---------------- --------------- ----------------
E4000M300(10.10.10.11) 1111111111111111 3 2222222222222222
--------------------------------------------------------------------------------
|
- The storage device and Fibre Channel switch for which set/delete/display is performed must have been registered in this product.
This command cannot be used to register Fibre Channel switches if zoning has not been set. Create a temporary zone and then register the Fibre Channel switch in this product. Refer to "4.2.1.1 Setting" for details on creating temporary zones.
- Please execute this command after confirming the state of the server is below. (When the server where HBA specified for "-hba" option is installed is registered in this product.)- The server had to have started when "Add" option was specified.- The server had to have stopped when "Delete" option was specified.
- Fibre Channel switch zoning is set for the Fibre Channel switch connected to the specified storage device CA.
- The Fibre Channel switch and storage device must be connected using a Fibre Channel cable. If the Fibre Channel cable is not connected, Fibre Channel switch zoning is not set. Connect the Fibre Channel cable, and then re-execute the command.
- Zone settings (creation of the AffinityGroup) must be configured in the ETERNUS disk array device in advance, using Storage Volume Configuration Navigator or ETERNUSmgr.
- Only the SN200 (except for model 250M) and Brocade (except for AP7420) Fibre Channel switch and PRIMERGY BX600 switchblades are supported.
- The following conformation message is output when 'delete' is specified. To continue, enter 'y'. To cancel, enter 'n'.
Are you sure? [y/n]:
This section explains the commands for starting and stopping daemons.
[In the case of PRIMEQUEST environment]
How to start a SNMP Trap-monitoring daemon
Input the following command to start a SNMP Trap-monitoring daemon
|
# /etc/init.d/sw-trapd start |
How to stop a SNMP Trap-monitoring daemon
Input the following command to stop a SNMP Trap-monitoring daemon.
|
# /etc/init.d/sw-trapd stop |
However, do not stop the daemon unless there is a special reason, for it affects software using snmptrapd (e.g.:PSA, ServerView).
How to check that a SNMP Trap-monitoring daemon has started
Input the following command to check if the process exists.
|
# /bin/ps -ef | grep nwsnmp-trapd | grep -v grep |
[In other cases than the PRIMEQUEST environment]
Starting the SNMP Trap monitoring daemon
Enter the following command to start the SNMP Trap monitoring daemon:
|
# /opt/FJSVswstt/bin/mpnm-trapd start |
Stopping the SNMP Trap monitoring daemon
Enter the following command to stop the SNMP Trap monitoring daemon:
|
# /opt/FJSVswstt/bin/mpnm-trapd stop |
Checking the SNMP Trap monitoring daemon
Enter the following command to confirm if the process exists.
|
# /bin/ps -ef | grep nwsnmp-trapd | grep -v grep |
Start or stop the following daemons in a batch operation:
|
Daemon name |
Admin server daemon SNMP Trap monitoring daemon |
Starting daemons of the administrative server
Enter the following command to start the administrative server:
|
# /opt/FJSVssmgr/sbin/managerctl start |
Stopping daemons of the administrative server
Enter the following command to stop the administrative server:
|
# /opt/FJSVssmgr/sbin/managerctl stop |
A SNMP Trap daemon is not stop in the PRIMEQUEST environment.
This section explains the commands for collecting troubleshooting information.
Function
Collect information on the administrative servers.
Use
rcxmgrsnap is the command used to collect information on administrative server when a problem occurs.
Submit the information to Fujitsu technical staff.
Format
|
# /opt/FJSVssmgr/sbin/managersnap [-dir directory] [-all] |
Parameter
No parameter
The troubleshooting information will be stored on /tmp directory.
- dir
Specify the directory where troubleshooting information is to be stored.
-all
Collects all troubleshooting information on servers. Data includes lots of information, which will increase the size of the data. This option is not necessary for initial investigation.
Example
|
# /opt/FJSVssmgr/sbin/managersnap |
This section explains command operations on the Windows administrative server.
The following sections explain the commands for managing the operating environment.
Function
This command sets administrative login account and perform creation of a CLI encryption key. Only user of OS administrative group can execute this command. This command only can execute when admin server stop.
Use
To create administrator login account.
Execute "rcxcert" command in "administrative-server-program-directory\Manager\opt\FJSVrcxmr\sbin\" directory.
Format
|
# cd administrative-server-program-directory\Manager\opt\FJSVrcxmr\sbin\ administrative-server-program-directory\Manager\opt\FJSVrcxmr\sbin>rcxcert setup |
Parameter
This command set the parameter by the following interface.
|
Input a new CLI crypt key [length:4-56]: any key Are you sure? [y,n,q?] y Input a new user name [length:1-16]: username Input a new password [length:1-16]: password Retype a new password [length:1-16]: password Are you sure? [y,n,q?] y |
CLI encryption key
Please enter the CLI encryption key to be used (between 4 and 56 characters). Double-byte characters, single-byte alphanumerical characters, symbols, and strings composed entirely of single or double-byte characters can be used. Notice that CLI encryption is required for ETERNUS SF Storage Cruiser internal use only, and users don't have to remember the key.
Username
Enter the user name of the login account for administrators (between 1 and 16 characters). The name must start with an alphabetic character, and alphanumerical characters (including underscores, "_", periods, ".", and hyphens, "-") can be used.
Password
Enter the password of the login account for administrators (between 1 and 16 characters). The password is a string of alphanumerical characters and symbols, but can not start with "{".
Password confirmation
For password confirmation, enter the password of the administrator again.
Examples
|
# cd "C:\Program Files\ETERNUS-SSC\Manager\opt\FJSVrcxmr\sbin" C:\Program Files\ETERNUS-SSC\Manager\opt\FJSVrcxmr\sbin>rcxcert setup |
Function
After the IP address of the administrative server is changed, this command deletes from the devices registered with this software product, the old IP address of the administrative server that is the SNMP Trap transmission place address, and then adds the new IP address.
Although the SNMP Trap transmission place setting for a device may be changed with the Management Software on the device, this software product provides this command to facilitate the changing of the transmission place.
Use
Execute the command after changing the IP address of Manager. The command is executed either for all devices managed by this software product or for selected devices.
Devices that can be targets of the command are devices for which SNMP Trap transmission settings can be defined automatically from this software product.
The monitoring status of every target device must be normal.
Format
|
administrative-server-program-directory\Manager\opt\FJSVssmgr\bin\sanadm chtraprcvip [-h / -all / DeviceID] -oldip xxx.xxx.xxx.xxx (-newip yyy.yyy.yyy.yyy) |
Parameter
-h
Displays Help concerning the argument format of the chtraprcvip command.
-all
Makes the SNMP Trap transmission place settings for all devices managed by this software product. Executing the command specified with this argument places device names and execution results in execution order on the standard output. If the administrative server has more than one IP address because, for example, the administrative server is connected to multiple subnets, the correct SNMP Trap transmission place may not be set for a device. After making this setting, therefore, check whether the correct administrative server address is set as the SNMP Trap transmission place address on the device.
DeviceID
Executes SNMP Trap transmission place setting for selected devices. Specify the device type in one of the device recognition methods listed in the table below:
|
Device type |
Device recognition methods (one of which must be specified) |
|
-host |
ip:xxx.xxx.xxx.xxx sysname: SysName name of SNMP set in the device nickname: Device management name that is set by this software. |
-oldip xxx.xxx.xxx.xxx
Specify the old IP address of the administrative server. Delete this IP address from the SNMP transmission place address of managed devices.
-newip yyy.yyy.yyy.yyy
Specify the new IP address of the administrative server. Add this IP address to the SNMP transmission place address of managed devices. If this argument is omitted, the IP address of the new administrative server is automatically specified. Fujitsu recommends that the argument be entered giving consideration to administrative servers having multiple IP addresses.
Examples
Execute SNMP Trap transmission place change processing for all managed devices that can automatically make the SNMP Trap transmission place settings.
|
"C:\Program Files\ETERNUS-SSC\Manager\opt\FJSVssmgr\bin\sanadm" chtraprcvip -all -oldip 100.100.100.100 -newip 200.200.200.200 |
Execute SNMP Trap transmission place change processing for the server node for which sysname is defined in host1.
|
"C:\Program Files\ETERNUS-SSC\Manager\opt\FJSVssmgr\bin\sanadm" chtraprcvip -host sysname:host1 -oldip 100.100.100.100 -newip 200.200.200.200 |
Function
This command checks whether this software product can receive an SNMP Trap correctly, display an event, and cooperate with Systemwalker Centric Manager and Shell.
A simulated Fibre Channel switch SNMP Trap (FC Port fault) is created and issued to the administrative server.
Use
Execute the command by specifying the IP address of a Fibre Channel switch whose trap setting is to be checked.
The target Fibre Channel switch must be a device managed by this software product.
Format
|
administrative-server-program-directory\Manager\opt\FJSVssmgr\bin\swtraptest fibre-channel-switch-ip-address |
Parameter
fibre-channel-switch-ip-address
Specify the IP address of the Fibre Channel switch which is to check the SNMP trap setting by this trap test command.
Example
Executing this command for a Fibre Channel switch whose IP address is 11.11.11.11
|
"C:\Program Files\ETERNUS-SSC\Manager\opt\FJSVssmgr\bin\swtraptest" 11.11.11.11 |
Even the input IP address is not for a FC device, this command can be executed.
In this case, it executes as the event of device which IP address is input.
Function
This command checks whether this software product can receive an SNMP Trap correctly, display an event, and cooperate with Systemwalker Centric Manager and Shell/Bat.
The administrative server internally generates pseudo SNMP traps (FAN fault) of the ETERNUS8000, ETERNUS6000, ETERNUS4000, ETERNUS3000, ETERNUS2000 and GR device, and issues them to the administrative server itself.
Use
Execute the command by specifying the IP address of a storage device whose trap setting is to be checked.
The target storage device must be a device managed by this software product.
Format
|
administrative-server-program-directory\Manager\opt\FJSVssmgr\bin\grtraptest storage-ip-address |
Parameter
storage-ip-address
Specify the IP address of the storage which is to check the SNMP trap setting by this trap test command.
Example
Executing the command for a storage device whose IP address is 12.12.12.12.
|
"C:\Program Files\ETERNUS-SSC\Manager\opt\FJSVssmgr\bin\grtraptest" 12.12.12.12 |
Even the input IP address is other than ETERNUS8000,ETERNUS6000, ETERNUS4000,ETERNUS3000, ETERNUS2000, GR series, and this command can be executed.
In this case, it executes as the event of device which IP address is input.
Function
This command enables the SNMP Trap port to function properly in systems where both ESC Manager and another Administrative software product are operating.
When the SNMP Trap monitor service starts, this command does specification that automatically starts Microsoft SNMP Trap Service.
Whenever Microsoft SNMP Trap Service is started, SNMP trap is received by way of Microsoft SNMP Trap Service.
Use
Execute the mpmsts command in management-server-environment-setup-directory\Manager\opt\FJSVswstt\bin directory.
Please execute this command in the environment with Microsoft SNMP Trap Service, and reboot your system.
Format
|
administrative-server-program-directory\Manager\opt\FJSVswstt\bin\mpmsts ON|OFF |
Parameter
ON:
Start Microsoft SNMP Trap Service automatically when SNMP Trap monitor service is start.
OFF:
Turn OFF the automatic start of Microsoft SNMP Trap Service.
Example
|
"C:\Program Files\ETERNUS-SSC\Manager\opt\FJSVswstt\bin\mpmsts" ON |
Function
This command is used to set/delete/display the storage device host affinity and Fibre Channel switch zoning.
Use
Specify the storage device CA WWPN, affinity group, and WWPN of the set HBA in the command parameter to set/delete the storage device host affinity and Fibre Channel switch zoning. The set host affinity and zoning is also displayed.
The target storage device and Fibre Channel switch must be devices managed by this product.
Format
|
administrative server program directory\Manager\opt\FJSVssmgr\sbin\storageadm zone add -storage cawwpn,affinitygroup -hba hbawwpn administrative server program directory\Manager\opt\FJSVssmgr\sbin\storageadm zone delete -storage cawwpn,affinitygroup -hba hbawwpn administrative server program directory\Manager\opt\FJSVssmgr\sbin\storageadm zone info [-ipaddr ipaddr[,ipaddr,...]] |
Parameter
add
This sets the host affinity and zoning.
delete
This deletes the host affinity and zoning.
info
This displays the host affinity and zoning.
-storage cawwpn,affinitygroup
Specify the storage device CA WWPN and affinity group for which the host affinity is set or deleted.
-hba hbawwpn
Specify the WWPN of the HBA set for host affinity and zoning.
-ipaddr ipaddr[,ipaddr,...]
Displays the host affinity information set in the specified IP address, Fibre Channel switch zoning information, or storage device CA.
To display more than one item of storage device information, specify the IP address using a comma (",").
If this omitted, all the storage device and Fibre Channel switch information registered in this product is displayed.
Examples
Adding the host affinity and zoning
|
"C:\Program Files\ETERNUS-SSC\Manager\opt\FJSVssmgr\sbin\storageadm" zone add -storage 1111111111111111,3 -hba 2222222222222222 |
Deleting the host affinity and zoning
|
"C:\Program Files\ETERNUS-SSC\Manager\opt\FJSVssmgr\sbin\storageadm" zone delete -storage 1111111111111111,3 -hba 2222222222222222 |
Displaying the host affinity and zoning
"C:\Program Files\ETERNUS-SSC\Manager\opt\FJSVssmgr\sbin\storageadm" zone info
<<< FC Switch Zone Information >>>
DEVICE_NAME(IP_ADDRESS) ZONE_NAME ZONE_WWPN
------------------------------ --------------- ---------------------------------
Switch1(10.10.10.10) SNM_0001 1111111111111111;2222222222222222
SNM_0002 3333333333333333;4444444444444444
--------------------------------------------------------------------------------
<<< FC CA Zone Information >>>
DEVICE_NAME(IP_ADDRESS) CA_WWPN AFFINITY_GROUP HBA_WWPN
------------------------------ ---------------- --------------- ----------------
E4000M300(10.10.10.11) 1111111111111111 3 2222222222222222
--------------------------------------------------------------------------------
|
- The storage device and Fibre Channel switch for which set/delete/display is performed must have been registered in this product.
This command cannot be used to register Fibre Channel switches is zoning has not been set. Create a temporary zone and then register the Fibre Channel switch in this product. Refer to "4.2.1.1 Settings" for details on creating temporary zones.
- Please execute this command after confirming the state of the server is below. (When the server where HBA specified for "-hba" option is installed is registered in this product.)- The server had to have started when "Add" option was specified.- The server had to have stopped when "Delete" option was specified.
- Fibre Channel switch zoning is set for the Fibre Channel switch connected to the specified storage device CA.
- The Fibre Channel switch and storage device must be connected using a Fibre Channel cable. If the Fibre Channel cable is not connected, Fibre Channel switch zoning is not set. Connect the Fibre Channel cable, and then re-execute the command.
- Zone settings (creation of the AffinityGroup) must be configured in the ETERNUS disk array device in advance, using Storage Volume Configuration Navigator or ETERNUSmgr.
- Only the SN200 (except for model 250M) and Brocade (except for AP7420) Fibre Channel switch and PRIMERGY BX600 switchblades are supported.
- The following conformation message is output when 'delete' is specified. To continue, enter 'y'. To cancel, enter 'n'.
Are you sure? [y/n]:
This section explains how to start and stop services.
Starting the services
Open "Control Panel"-"Administrative Tools"-"Services", select the service "ETERNUS SF Storage Cruiser Manager" and start it.
Stopping the services
Open "Control Panel"-"Administrative Tools"-"Services", select the service "ETERNUS SF Storage Cruiser Manager" and stop it.
Starting the SNMP Trap monitoring service
Open "Control Panel"-"Administrative Tools"-"Services", select the service " Systemwalker MpWksttr" and start it.
Stopping the SNMP Trap monitoring service
Open "Control Panel"-"Administrative Tools"-"Services", select the service " Systemwalker MpWksttr" and stop it.
Checking the SNMP Trap monitoring service
Open "Control Panel"-"Administrative Tools"-"Services", select the service " Systemwalker MpWksttr" and check it by the status of "start" button.
Function
This command adds the operation item selected from the operation menu in the monitoring window of the Systemwalker Centric Manager administrative client to the popup menu that is displayed by right-clicking a node on the map. For information about the command, see mpaplreg in the Systemwalker Centric manager Reference Manual.
Use
Execute this command to linkage ESC monitor window to Systemwalker Centric manager client window.
Format
|
mpaplreg -a -m application_name -p server_node_name -c command_line mpaplreg -d -m application_name mpaplreg -v -m application_name |
Parameter
-m
Specify a name for the item added to the menu.
Specify "ESC" for example.
-p
Specify the server node name of the managed node for which you want to add the menu item.
Specify the host name of the node registered in Systemwalker Centric Manager.
-c
Specify the command line entry to be executed when the menu item is selected,
Specify the startup command path of the Client.
-v
Displays a registered menu item.
-d
Deletes a registered menu item.
Note the following about executing the command:
Perform this operation each time a storage device is added.
Only a user belonging to the administrator group of the administrative client can perform this operation.
Example
Addition to a menu
|
mpaplreg -a -m ESC -p tama -c "\"C:\Program Files\ETERNUS-SSC\Client\bin\rcxclient.exe\"" |
Deletion from a menu
|
mpaplreg -d -m ESC |
Confirmation of content of menu registration
|
mpaplreg -v -m ESC Modification example: Administrative domain name : melba |
This section explains command operations on Solaris OS Agent machines.
The following sections explain the commands for managing the operating environment.
Function
This command sets user information necessary for database monitoring. Based on the information set with the defusr command, Agent accesses a database and collects information.
User information specified with the defusr command is used only by Agent to access the database and collect information, and it is not related to the user who has started Agent or the user who has logged in to the administrative client machine.
Use
Only users having administrator authority can execute this command to set or reset user information necessary for database monitoring. Up to 63 letters can be specified individually for the key name, user name, and password of the defusr command. However, Japanese characters (double-byte characters) cannot be specified for the key name, user name, and password of the defusr command.
Format
|
# /opt/FJSVssage/bin/defusr -a key-name user-name password # /opt/FJSVssage/bin/defusr -l [key-name] # /opt/FJSVssage/bin/defusr -r key-name user-name password # /opt/FJSVssage/bin/defusr -d key-name |
Format
The following is specified for key name, user name, and password.
|
Monitored object |
Key name |
User name, password |
|---|---|---|
|
Oracle |
Instance name specified in Oracle statement |
User information to access to instance specified by key name |
-a
Registers user information. Up to 255 sets of user information can be registered. An attempt at registration with an existing key results in an error.
-l
Displays user information. The user name defined for a specified key name is displayed. If no key name is specified, all registered user names are displayed.
-r
Changes user information.
-d
Deletes user information.
Examples
Registering user information
|
# /opt/FJSVssage/bin/defusr -a key1 user pass |
Changing user information
|
# /opt/FJSVssage/bin/defusr -r key1 user pass |
Function
This command sets Agent information.
Use
To change the start IP address of Agent, specify an IP address in the command parameter to specify Agent information. The specified Agent start IP address must be the IP address of a server node that can communicate with the administrative server.
Format
|
# /opt/FJSVssage/bin/setagtip [-i IP_address] |
Parameter
Default
Displays the current setting information.
-i
Sets the specified IP address as the start IP address of Agent.
Specify the IP address of the server node that can communicate from the
operation control server.
Examples
Displaying Agent information
|
# /opt/FJSVssage/bin/setagtip |
Setting the Agent IP address to 10.12.13.14
|
# /opt/FJSVssage/bin/setagtip -i 10.12.13.14 |
If the host name cannot be resolved from the specified IP address, the messages shown below is displayed. Check for an error in the specified IP address or network definition (hosts, DNS, etc.), and re-execute the command.
IP Address = IP address: Host's Name is not found.
Function
This command checks whether SNMP Trap is correctly transmitted to a administrative server from a server node agent, display an event, and check the linkage with Shell/Bat. The Centric Manager linkage is not operated by this command.
If the action on SNMP Trap as a test is supposed to be changed, change SNMP Trap XML definition file (1_3_6_1_4_1_211_4_1_3_21_2_2.xml) for the ESC agent. In SNMP Trap as a test, 1 is used for Specific Trap Type number and the action can be changed by changing the definition of the Specific Trap Type number 1 defined in SNMP Trap XML definition file. For SNMP Trap XML definition file, refer to "D.6 SNMP Trap XML Definition File".
Use
From a server node agent, the command which transmits SNMP Trap as a test is executed.
Format
|
# /opt/FJSVssagt/bin/traptest [IP_address] |
Parameter
IP_address
Only in the environment where the host holds two or more IP addresses, a server node's IP (Agent start IP address) address which the ESC manager recognizes is specified to IP_address.
Examples
SNMP Trap is transmitted from the server node agent of IP address 11.11.11.11.
|
# /opt/FJSVssagt/bin/traptest 11.11.11.11 |
If the SNMP Trap destination address is not set to the server node when execute the command, the following results are output.
If the server node that input in the command is not registered in ESC, please re-execute the command after registering the server node.
Please execute the same action in case where the server node is not registered in ESC after deletion of the server node.
|
Target Host Nothing SNMPTrap error |
This command sets Starting and Stopping Agent
Starting Agent
Enter the following command to start Agent.
|
# /opt/FJSVssage/bin/sstorageagt |
Stopping Agent
Enter the following command to stop Agent.
|
# /opt/FJSVssage/bin/pstorageagt |
This section explains the commands for collecting troubleshooting information on agent.
Function
Collect information on the agent.
Use
Collect information on agent when a problem occurs.
Submit the information to Fujitsu technical staff.
Format
|
# /opt/FJSVssage/sys/agentsnap [-dir dir] [-all] |
Parameter
No parameter
The troubleshooting information will be stored on /tmp directory.
- dir
Specify the directory where troubleshooting information is to be stored.
-all
Collects all troubleshooting information on servers. Data includes lots of information, which will increase the size of the data. This option is not necessary for initial investigation.
Examples
|
# /opt/FJSVssage/sys/agentsnap |
This section explains command operations on Windows Agent machines.
The following sections explain the commands for managing the operating environment.
Function
This command sets user information necessary for database monitoring. Based on the information set with the defusr command, Agent accesses a database and collects information. User information specified with the defusr command is used only by Agent to access the database and collect information, but it is not related to the user who has started Agent or the user who has logged in to the Client machine.
Use
Only users having administrator authority can execute this command to set or reset user information necessary for database monitoring. Up to 63 letters can be specified individually for the key name, user name, and password of the defusr command. However, Japanese characters (double-byte characters) cannot be specified for the key name, user name, and password of the defusr command.
Format
|
agent-program-directory\Agent\bin\defusr -a keyname username password agent-program-directory\Agent\bin\defusr -l [keyname] agent-program-directory\Agent\bin\defusr -r keyname username password agent-program-directory\Agent\bin\defusr -d keyname |
Parameter
The following is specified for key name, user name, and password.
|
Monitored object |
Key name |
User name, password |
|---|---|---|
|
Oracle |
Instance name specified in Oracle statement |
User information to access to instance specified by key name |
|
SQL Server |
Arbitrary name (The same name as the key name specified in SQL Server statement) |
User information to access to instance specified by SQL Server statement |
-a
Registers user information. Up to 255 sets of user information can be registered. An attempt at registration with an existing key results in an error.
-l
Displays user information. The user name defined for a specified key name is displayed. If no key name is specified, all registered user names are displayed.
-r
Changes user information.
-d
Deletes user information.
Examples
Registering user information
|
"C:\Program Files\ETERNUS-SSC\Agent\bin\defusr" -a key1 user pass |
Changing user information
|
"C:\Program Files\ETERNUS-SSC\Agent\bin\defusr" -r key1 user pass |
Function
This command sets Agent information.
Use
To change the start IP address of Agent, specify an IP address in the command parameter for this setting.
Format
|
agent-program-directory\Agent\bin\setagtip [-i ip_address] |
Parameter
Default
Displays the current setting information.
-i
Sets a specified IP address as the start IP address of Agent.
Specify the IP address of the server node that can communicate from the
operation control server.
Examples
Displaying Agent information
|
"C:\Program Files\ETERNUS-SSC\Agent\bin\setagtip" |
Setting the Agent IP address to 10.12.13.14
|
"C:\Program Files\ETERNUS-SSC\Agent\bin\setagtip" -i 10.12.13.14 |
If the host name cannot be resolved from the specified IP address, the messages shown below is displayed. Check for an error in the specified IP address or network definition (hosts, DNS, etc.), and re-execute the command.
IP Address = IP address: Host's Name is not found.
Function
This command checks whether SNMP Trap is correctly transmitted to a administrative server from a server node agent, display an event, and check the linkage with Shell/Bat. The Centric Manager linkage is not operated by this command.
If the action on SNMP Trap as a test is supposed to be changed, change SNMP Trap XML definition file (1_3_6_1_4_1_211_4_1_3_21_2_2.xml) for the ESC agent. In SNMP Trap as a test, 1 is used for Specific Trap Type number and the action can be changed by changing the definition of the Specific Trap Type number 1 defined in SNMP Trap XML definition file. For SNMP Trap XML definition file, refer to "D.6 SNMP Trap XML Definition File".
Use
From a server node agent, the command which transmits SNMP Trap as a test is executed.
Format
|
agent-installation-directory\Agent\bin\traptest [IP_address] |
Parameter
IP_address:
Only in the environment where the server node holds two or more IP addresses, a server node's IP (Agent start IP address) address which the ESC manager recognizes is specified to IP_address.
Examples
SNMP Trap is transmitted from the server node agent of IP address 11.11.11.11.
|
"C:\Program Files\ETERNUS-SSC\Agent\bin\traptest" 11.11.11.11 |
If the SNMP Trap destination address is not set to the server node when execute the command, the following results are output.
If the server node that input in the command is not registered in ESC, please re-execute the command after registering the server node.
Please execute the same action in case where the server node is not registered in ESC after deletion of the server node.
|
Target Host Nothing SNMPTrap error |
This section explains the commands for starting and stopping services.
Starting the service
Open "Services" from "Management Tool" of "Control Panel" and select ETERNUS SF Storage Cruiser Agent to start the service.
Stopping the CIMOM service
Open "Services" from "Management Tool" of "Control Panel" and select ETERNUS SF Storage Cruiser Agent to stop the service.
This section explains command operations on Linux OS Agent machines.
The following sections explain the commands for managing the operating environment.
Function
This command sets user information required for database monitoring. Based on the user information set by the defusr command, Agent accesses the database and collects information.
The user information set by the defusr command is used only by Agent to access the database to collect information and has nothing to do with the Agent start user and the login user of an administrative client.
Use
A user with administrator authority executes this command to set or delete user information required for database monitoring. Each of the key name, user name, and password in the defusr command can be specified using up to 63 characters. Two-byte characters cannot be used.
Format
|
# /opt/FJSVssage/bin/defusr -a keyname username password # /opt/FJSVssage/bin/defusr -l [keyname] # /opt/FJSVssage/bin/defusr -r keyname username password # /opt/FJSVssage/bin/defusr -d keyname |
Parameter
|
Monitoring target |
Key name |
User name and password |
|---|---|---|
|
Oracle |
Instance name specified in the Oracle statement |
User information needed to access the instance specified for the key name |
-a
Adds user information. Up to 255 pieces of user information can be stored. An attempt to add user information to a key for which user information has already been stored causes an error.
-l
Displays user information. The user name defined for the specified key name is displayed. If the key name is not specified, all user names that have been registered are displayed.
-r
Modifies user information.
-d
Deletes user information.
Examples
Adding user information
|
# /opt/FJSVssage/bin/defusr -a key1 user pass |
Modifying user information
|
# /opt/FJSVssage/bin/defusr -r key1 user pass |
Function
This command sets Agent information.
Use
To change the start IP address of Agent, specify an IP address in the command parameter to specify Agent information. The specified Agent start IP address must be the IP address of a server node that can communicate with the administrative server.
Format
|
# /opt/FJSVssage/bin/setagtip [-i ip_address] |
Parameter
Default
Displays the current setting information.
-i
Sets the specified IP address as the start IP address of Agent.
Specify the IP address of the server node that can communicate from the
operation control server.
Examples
Displaying Agent information
|
# /opt/FJSVssage/bin/setagtip |
Setting the Agent IP address to 10.12.13.14
|
# /opt/FJSVssage/bin/setagtip -i 10.12.13.14 |
If the host name cannot be resolved from the specified IP address, the messages shown below is displayed. Check for an error in the specified IP address or network definition (hosts, DNS, etc.), and re-execute the command.
IP Address = IP address: Host's Name is not found.
Function
This command checks whether SNMP Trap is correctly transmitted to a administrative server from a server node agent, display an event, and check the linkage with Shell/Bat. The Centric Manager linkage is not operated by this command.
If the action on SNMP Trap as a test is supposed to be changed, change SNMP Trap XML definition file (1_3_6_1_4_1_211_4_1_3_21_2_2.xml) for the ESC agent. In SNMP Trap as a test, 1 is used for Specific Trap Type number and the action can be changed by changing the definition of the Specific Trap Type number 1 defined in SNMP Trap XML definition file. For SNMP Trap XML definition file, refer to "D.6 SNMP Trap XML Definition File".
Use
From a server node agent, the command which transmits SNMP Trap as a test is executed.
Format
|
# /opt/FJSVssagt/bin/traptest [IP_address] |
Parameter
IP_address:
Only in the environment where the host holds two or more IP addresses, a server node's IP (Agent start IP address) address which the ESC manager recognizes is specified to IP_address.
Examples
SNMP Trap is transmitted from the server node agent of IP address 11.11.11.11.
|
# /opt/FJSVssagt/bin/traptest 11.11.11.11 |
If the SNMP Trap destination address is not set to the server node when execute the command, the following results are output.
If the server node that input in the command is not registered in ESC, please re-execute the command after registering the server node.
Please execute the same action in case where the server node is not registered in ESC after deletion of the server node.
|
Target Host Nothing SNMPTrap error |
This section explains the commands for starting and stopping agent.
Starting Agent
Enter the following command to start Agent.
|
# /opt/FJSVssage/bin/sstorageagt |
Stopping Agent
Enter the following command to stop Agent.
|
# /opt/FJSVssage/bin/pstorageagt |
This section explains the commands for troubleshooting information on agent.
Function
Collect information on the agent.
Use
Collect information on agent when a problem occurs.
Submit the information to Fujitsu technical staff.
Format
|
# /opt/FJSVssage/sys/agentsnap [-dir dir][-all] |
Parameter
No parameter
The troubleshooting information will be stored on /tmp directory.
- dir
Specify the directory where troubleshooting information is to be stored.
-all
Collects all troubleshooting information on servers. Data includes lots of information, which will increase the size of the data. This option is not necessary for initial investigation.
Examples
|
# /opt/FJSVssage/sys/agentsnap |
This section explains the command operations on HP-UX Agent machines.
The following sections explain the commands for managing the operating environment.
Function
This command sets the Agent information.
Use
To change the start of the IP address of Agent, specify an IP address in the command parameter for this setting.
The specified Agent start IP address must be the IP address of a server node that can communicate with the administrative server.
Format
|
# /opt/FJSVssage/bin/setagtip [-i IP_address] |
Parameter
Default
Displays the current setting information.
-i
Sets the specified IP address as the start IP address of Agent.
Specify the IP address of the server node that can communicate from the
operation control server.
Examples
Displaying Agent information
|
# /opt/FJSVssage/bin/setagtip |
Setting the Agent IP address to 10.12.13.14.
|
# /opt/FJSVssage/bin/setagtip -i 10.12.13.14 |
If the host name cannot be resolved from the specified IP address, the message shown below is displayed. Check for an error in the specified IP address or network definition (hosts, DNS, etc.), and re-execute the command.
IP Address = IP address : Host's Name is not found.
Function
This command checks whether SNMP Trap is correctly transmitted to a administrative server from a server node agent, display an event, and check the linkage with Shell/Bat. The Centric Manager linkage is not operated by this command.
If the action on SNMP Trap as a test is supposed to be changed, change SNMP Trap XML definition file (1_3_6_1_4_1_211_4_1_3_21_2_2.xml) for the ESC agent. In SNMP Trap as a test, 1 is used for Specific Trap Type number and the action can be changed by changing the definition of the Specific Trap Type number 1 defined in SNMP Trap XML definition file. For SNMP Trap XML definition file, refer to "D.6 SNMP Trap XML Definition File".
Use
From a server node agent, the command which transmits SNMP Trap as a test is executed.
Format
|
# /opt/FJSVssagt/bin/traptest [IP_address] |
Parameter
IP_address:
Only in the environment where the host holds two or more IP addresses, a server node's IP (Agent start IP address) address which the ESC manager recognizes is specified to IP_address.
Command input examples
SNMP Trap is transmitted from the server node agent of IP address 11.11.11.11.
|
# /opt/FJSVssagt/bin/traptest 11.11.11.11 |
If the SNMP Trap destination address is not set to the server node when execute the command, the following results are output.
If the server node that input in the command is not registered in ESC, please re-execute the command after registering the server node.
Please execute the same action in case where the server node is not registered in ESC after deletion of the server node.
|
Target Host Nothing SNMPTrap error |
This section explains the commands for starting and stopping agent.
Starting Agent
Execute the following command to start Agent.
|
# /opt/FJSVssage/bin/sstorageagt |
Stopping Agent
Execute the following command to stop Agent.
|
# /opt/FJSVssage/bin/pstorageagt |
|
Contents
Index
|