自動リカバリの動作対象とするイベント(SNMP Trap)は、以下のとおりです。
MIB-OID: 1.3.6.1.4.1.231.2.10.2 (SERVER-CONTROL-MIB)
specific trap type message 601 Fan failed 603 Temperature warning 604 Temperature critical 606 AC failed, on battery 609 Controller selftest error 612 UPS not detected 615 SE's missing 622 Fan will fail 626 Power supply failed 628 Power supply critical 630 Temperature sensor broken 632 AC failed 633 Duplicate cabinet ID 638 Uncorrectable memory error 640 Uncorrectable memory error 642 Uncorrectable memory error 644 Uncorrectable memory error 648 Redundant fan failed 649 Redundant power supply failed 651 Voltage too low 652 Voltage too high 666 Boot retry counter zero 668 Memory module prefailure 669 Memory module failing 670 Memory module replaced 673 CPU prefailure 674 Power failed 675 Critical BIOS selftest error 676 BIOS selftest watchdog expired 677 Voltage out of range 678 Battery failure predicted 679 The system was restarted after a severe problem 750 SMART predicted disk failure 1101 Customer self service warning 1102 Customer self service fail 2004 Controller selftest error 2005 Critical BIOS selftest error 2006 The system was restarted after a severe problem 2013 Fan failure predicted 2014 Fan failed 2015 Redundant fan failed 2021 Temperature warning 2022 Temperature critical 2024 Temperature sensor broken 2033 Power supply critical 2034 Power supply failed 2035 Redundant power supply failed 2040 AC failed 2041 Power failed 2042 AC failed, on battery 2051 Voltage too low 2052 Voltage too high 2053 Voltage out of range 2054 Battery failure predicted 2061 Uncorrectable memory error 2063 Uncorrectable memory error 2065 Uncorrectable memory error 2067 Uncorrectable memory error 2068 Memory module prefailure 2069 Memory module failing 2070 Memory module replaced 2073 Memory module replaced 2074 Memory redundancy lost 2081 CPU prefailure 2095 Boot retry counter zero 2102 Error in message log 2110 Front door or housing opened 2112 Front door or housing opened/closed 2113 PCI bus system/parity error
MIB-OID: 1.3.6.1.4.1.231.2.10.2.2.10.20 (SERVER-CONTROL2-MIB)
specific trap type message 2004 Controller selftest error 2005 Critical BIOS selftest error 2006 The system was restarted after a severe problem 2013 Fan failure predicted 2014 Fan failed 2015 Redundant fan failed 2021 Temperature warning, type %s 2022 Temperature critical, type %s 2024 Temperature sensor broken 2033 Power supply critical 2034 Power supply failed 2035 Redundant power supply failed 2040 AC failed 2041 Power failed 2042 AC failed, on battery 2051 Voltage too low 2052 Voltage too high 2053 Voltage out of range 2054 Battery failure predicted 2061 Uncorrectable memory error 2063 Uncorrectable memory error 2065 Uncorrectable memory error 2067 Uncorrectable memory error 2068 Memory module prefailure 2069 Memory module failing 2070 Memory module replaced 2073 Memory module replaced 2074 Memory redundancy lost 2081 CPU prefailure 2095 Boot retry counter zero 2102 Error in message log 2113 PCI bus system/parity error 2120 Customer self service warning 2121 Customer self service fail 2122 Customer self service warning 2123 Customer self service fail
MIB-OID:1.3.6.1.4.1.231.2.49.2 (FSC-RAID-MIB)
specific trap type message 10003 Battery Temperature out of Range 10004 Battery Temperature unstable 10005 Battery Temperature above threshold 10006 Battery Voltage out of Range 10007 Battery Voltage unstable 10008 Battery Voltage below threshold 10009 Battery Communication Error 10013 Battery failed 10014 Battery Fast Charging failed 10022 Physical Disk marked offline 10023 Physical Disk timed out 10030 Rebuild on Physical Disk failed 10031 Bad Block on Physical Disk detected 10036 Bad Sector on Physical Disk detected 10037 COD I/O Error on Physical Disk 10038 Error on Physical Disk detected 10040 Retry I/O on Physical Disk 10041 ECC Error on Physical Disk 10043 Media Error on Physical Disk 10046 Bad Physical Disk inserted in Enclosure 10047 Enclosure powered down 10049 Fan in Enclosure failed 10050 Temperature Sensor in Enclosure above Threshold 10051 Power Supply in Enclosure failed 10052 3.3V Power failed for Physical Disk 10053 5.0V Power failed for Physical Disk 10054 12V Power failed for Physical Disk 10057 Rebuild failed on Logical Drive 10062 Consistency Check failed on Logical Drive 10066 Consistency Check finished with Errors on Logical Drive 10067 Inconsistency detected on Logical Drive 10070 Migration failed on Logical Drive 10078 Logical Drive degraded 10079 Logical Drive failed 10083 Logical Drive Error on Physical Disk 10084 Logical Drive: Bad Block detected 10093 Hotspare Operation on Logical Drive failed 10094 Logical Drive forced from failed to degraded 10151 BBU Voltage Problem detected 10152 BBU Temperature Problem detected 10154 BBU failed 10170 Reboot required 10195 Unable to recover cache data from TBBU 10197 Cluster down; communication with peer lost 10201 Unable to recover cache data 10204 Fatal firmware error 10206 Flash downloaded image corrupt 10207 Flash erase error 10208 Flash timeout during erase 10209 Flash error 10212 Flash programming error 10213 Flash timeout during programming 10215 Flash command set unknown 10216 Flash verify failure 10221 Multi-bit ECC error 10222 Single-bit ECC error 10223 Not enough controller memory 10231 Background Initialization completed with uncorrectable errors 10232 Background Initialization detected uncorrectable double medium errors 10233 Background Initialization failed 10237 Consistency Check found inconsistent parity 10240 Initialization failed 10245 Reconstruct detected uncorrectable double medium errors 10248 Reconstruction resume failed 10251 Clear failed 10255 Error on Physical Drive 10258 Hot Spare S.M.A.R.T. polling failed 10259 Physical Disk not supported 10262 Patrol Read found an uncorrectable medium error 10264 Puncturing bad block 10271 Rebuild stopped 10272 Reassign write operation failed 10273 Unrecoverable medium error during rebuild 10275 Unrecoverable medium error during recovery 10279 Redundant path broken 10294 Unable to access Physical Disk 10320 Enclosure fan removed 10321 Enclosure EMM failed 10323 Enclosure EMM removed 10327 Enclosure sensor bad 10376 Enclosure Firmware download failed 10388 Logical Drive is PARTIALLY DEGRADED 10398 MDC finished with Errors on Logical Drive 10408 MDC failed on Logical Drive 10412 State change from operational to degraded 10413 State change from operational to partially degraded 10414 State change from operational to failed 10416 State change from degraded to degraded 10417 State change from degraded to partially degraded 10418 State change from degraded to failed 10420 State change from partially degraded to degraded 10421 State change from partially degraded to partially degraded 10422 State change from partially degraded to failed 10424 State change from failed to degraded 10425 State change from failed to partially degraded 10426 State change from failed to failed 10427 State change by user from available to failed 10432 State change by user from failed to failed 10437 State change by user from hotspare to failed 10442 State change by user from rebuild to failed 10447 State change by user from operational to failed 10451 State change from available to failed 10456 State change from failed to failed 10461 State change from hotspare to failed 10466 State change from rebuild to failed 10471 State change from operational to failed 10475 MDC detected uncorrectable multiple medium errors on Logical Drive 10476 Physical drive missing after reboot 10477 Logical drive missing after reboot 10480 Puncture enabled 10481 Puncture disabled 10482 Enclosure EMM not installed 10490 State change by user from offline to failed 10500 State change from offline to failed 10508 Data in cache not flushed during power up 10512 Logical drive error on disk media 10514 Consistency check finished with errors on logical drive 10515 Error on logical drive detected 10516 Disk forced from failed to online 10518 SAS port lost link 10526 Adapter missing after reboot 10529 Consistency check finished with correctable errors on logical drive 10530 Consistency check finished with uncorrectable errors on logical drive 10532 MDC finished with uncorrectable errors on logical drive 10539 Bad block table on logical drive is full 10540 Uncorrectable medium error logged for logical drive 10544 Adapter needs replacement, faulty IOP detected 10551 Copyback failed on disk 10570 Copyback aborted on hot spare 10572 Cache discarded for logical drive (missing or offline) 10575 Redundancy building failed on disk 10616 Security subsystem problems detected for disk 10617 Adapter cache pinned for missing or offline logical drive 10618 Adapter cache pinned for missing or offline logical drives 10626 Internal hardware error 10627 Internal hardware error during POST 10630 Disk failed due to bad block table overflow 10631 Disk failure detected during POST 10632 Failure detected during POST 10633 Multiple failure on disk detected 10635 Disk failure detected by Patrol Read 10636 Disk failure detected after successfully building redundancy 10637 Disk failure detected after aborting building redundancy 10638 Disk failed 10639 Disk failed 10662 Copyback on logical drive aborted due to bad block table overflow 10663 Redundant copy on logical drive aborted due to bad block table overflow 10685 Internal hardware error 10686 Disk bad block table overflow error 10688 Multiple failure on disk detected during POST 10689 Disk failed due to SAS/SATA interface error rate too high 10694 Logical drive degraded due to bad block table overflow 10695 Disk failed due to write error detection by driver 10700 Internal PCI hardware error 10711 Disk failed since it never entered ready state 10717 Firmware initialization failed 10718 Firmware recovery failed 10734 Task for object cannot be started. The scheduler has disabled the task 10736 SAS topology error
MIB-OID:1.3.6.1.4.1.1597 (DPT-SCSI-MIB)
specific trap type message 400 Very high temperature on controller 401 Array failed 300 5V Voltage outside range on controller 302 Controller detected an ECC RAM error that could not be corrected 303 Array degraded 304 Serious: Request sense data received. 305 Array data inconsistency found. 306 controller error found. 307 Unprotected drive has failed. 308 SMART failure reported. 309 Auxiliary voltage outside range on controller 310 5V Voltage outside range on controller 311 Auxiliary voltage outside range on controller
MIB-OID:1.3.6.1.4.1.1608 (MYLEXRAID-MIB)
specific trap type message 3 Physical disk error found. 4 Physical disk PFA condition found; this disk may fail soon. 9 Rebuild stopped with error. 10 Rebuild stopped with error. New physical disk failed. 11 Rebuild stopped because logical drive failed. 12 A physical disk has failed. 18 Expand Capacity Stopped with error. 19 SCSI command timeout on physical device. 20 SCSI command abort on physical disk. 22 Parity error found. 28 Request Sense Data available. 31 Initialization failed. 32 Initialization canceled. 33 A physical disk failed because write recovery failed. 34 A physical disk failed because SCSI bus reset failed. 35 A physical disk failed because double check condition occured. 36 A physical disk failed because device is missing. 37 A physical disk failed because of gross error on SCSI processor. 38 A physical disk failed because of invalid tag. 39 A physical disk failed because a command timed out. 40 A physical disk failed because of the system reset. 41 A physical disk failed because of busy status or parity error. 42 A physical disk set to failed state by host. 43 A physical disk failed because access to the device met with a selection time out. 44 A physical disk failed because of a sequence error in the SCSI bus phase handling. 45 A physical disk failed because device returned an unknown status. 46 A physical disk failed because device is not ready. 47 A physical disk failed because device was not found on start up. 48 A physical disk failed because write operation of the 'Configuration On Disk' failed. 49 A physical disk failed because write operation of 'Bad Data Table' failed. 50 Physical disk status changed to offline. 52 Physical disk status changed to rebuild. 54 Physical disk failed to start. 57 Physical disk missing on startup. 58 Rebuild startup failed due to lower physical disk capacity. 59 Physical disk is switching from one channel to the other channel. 60 Temporary-Dead physical disk is automatically made online. 64 A storage access path has been lost. 65 A storage access path has shifted to the alternate path. 67 Physical Disk found on only one disk channel. 69 Physical disk has acquired an inappropriate loop ID. Enclosure disk-slot operations are disabled while this condition persists. 70 Physical disk port has failed or cannot operate at the configured channel speed. 71 Mirror Race recovery failed for logical drive. 72 Controller parameters checksum verification failed - restored default. 75 Online firmware upgrade has failed. 78 Battery backup unit charger error. 79 Battery will not hold a charge. 80 Firmware entered unexpected state at run-time. 82 Check Consistency stopped on controller failure. 83 Foreground Init stopped on controller failure. 90 Channel is suspended due to some faults. 96 Device loop ID conflict (soft addressing) detected. 130 Consistency check is cancelled. 131 Consistency check on logical drive error. 132 Consistency check on logical drive failed. 133 Consistency check failed due to physical disk failure. 134 Logical drive has been made offline. 135 Logical drive is critical. 140 Rebuild on logical drive is cancelled. 141 Rebuild stopped with error. 142 Rebuild stopped with error. New physical disk failed. 143 Rebuild stopped because logical drive failed. 146 Logical drive initialization cancelled. 147 Logical drive initialization failed. 152 Expand capacity stopped with error. 153 Bad Blocks found. 156 Bad data blocks found. Possible data loss. 158 Attempt to read data from block that is marked in Bad Data Table. 159 Data for Disk Block has been lost due to Logical Drive problem. 160 Temporary-Offline RAID5/RAID3 array is available to the user again with the possibility of data loss in the array. 161 Temporary-Offline RAID0+1/RAID1/RAID0/JBOD array is available to the user again. 180 Logical drive background initialization failed. 182 Low battery charge level. Logical drive may have lost data. 183 Inconsistent data found during consistency check. 256 Fan failure. 258 Fan failure. 272 Power supply failure. 274 Power supply failure. 288 Over temperature. Temperature is above 70 degrees Celsius. 291 Over temperature. 304 Storage Works enclosure reported failure state. 305 Storage Works enclosure reported critical state. 309 Uninterruptible power supply battery low. 310 Uninterruptible power supply failed. 320 Fan failure. 323 Power supply failure. 326 Temperature is over safe limit. Failure imminent. 327 Temperature is above working limit. 330 Enclosure access critical. 332 Enclosure access is offline. 333 Enclosure soft addressing detected. 338 Physical disks in enclosure being spundown. 339 Temperature is below working limit. 340 Temperature is under safe limit. Failure imminent. 385 Write back error. 388 Controller is dead. System is disconnecting from this controller. 391 Controller is gone. System is disconnecting from this controller. 393 Battery is bad. 395 Controller is gone. System is disconnecting from this controller. 398 Controller is gone. System is disconnecting from this controller. 403 Installation aborted. 404 Controller firmware mismatch. 405 The Battery Backup Unit is removed. 406 WARM BOOT failed. 410 Battery is not present. 414 Soft ECC error corrected. 415 Hard ECC error corrected. 418 BBU out of service. 423 Disabled partner. 425 Controller boot ROM image needs to be reloaded. 426 Controller is using default non-unique world-wide name. 427 Mirror Race recovery failed. 428 Mirror Race on critical logical drive. 431 Controller improperly shutdown! Data may have been lost. 433 Dual-active negotiation failed jumpers. 434 Dual-active negotiation failed IDs. 435 Dual-active negotiation failed board types. 436 Dual-active negotiation failed disk channels. 437 Dual-active negotiation failed host ports. 438 Dual-active negotiation failed memory size. 439 Dual-active negotiation failed cache memory size. 440 Error in Mirror Race Table. 441 A replacement controller attempted to stop the surviving controller. 447 Data in Cache not flushed during power up. 517 Lost connection to server, or server is down. 522 Battery test failed - battery bad 642 Back end SCSI bus dead. 644 Back end fibre dead. 896 Internal controller hung. 897 Internal controller firmware breakpoint. 898 Firmware internal Exception condition. 912 Internal controller i960 processor error. 928 Internal controller Strong-ARM processor error. 944 Internal Controller Backend Hardware Error.
MIB-OID:1.3.6.1.4.1.1608.1.1.1.9.1 (MYLEXRAID-MIB)
specific trap type message 3 Physical disk error found. 4 Physical disk PFA condition found; this disk may fail soon. 9 Rebuild stopped with error. 10 Rebuild stopped with error. New physical disk failed. 11 Rebuild stopped because logical drive failed. 12 A physical disk has failed. 18 Expand Capacity Stopped with error. 19 SCSI command timeout on physical device. 20 SCSI command abort on physical disk. 22 Parity error found. 28 Request Sense Data available. 31 Initialization failed. 32 Initialization canceled. 33 A physical disk failed because write recovery failed. 34 A physical disk failed because SCSI bus reset failed. 35 A physical disk failed because double check condition occured. 36 A physical disk failed because device is missing. 37 A physical disk failed because of gross error on SCSI processor. 38 A physical disk failed because of invalid tag. 39 A physical disk failed because a command timed out. 40 A physical disk failed because of the system reset. 41 A physical disk failed because of busy status or parity error. 42 A physical disk set to failed state by host. 43 A physical disk failed because access to the device met with a selection time out. 44 A physical disk failed because of a sequence error in the SCSI bus phase handling. 45 A physical disk failed because device returned an unknown status. 46 A physical disk failed because device is not ready. 47 A physical disk failed because device was not found on start up. 48 A physical disk failed because write operation of the 'Configuration On Disk' failed. 49 A physical disk failed because write operation of 'Bad Data Table' failed. 50 Physical disk status changed to offline. 52 Physical disk status changed to rebuild. 54 Physical disk failed to start. 57 Physical disk missing on startup. 58 Rebuild startup failed due to lower physical disk capacity. 59 Physical disk is switching from one channel to the other channel. 60 Temporary-Dead physical disk is automatically made online. 64 A storage access path has been lost. 65 A storage access path has shifted to the alternate path. 67 Physical Disk found on only one disk channel. 69 Physical disk has acquired an inappropriate loop ID. Enclosure disk-slot operations are disabled while this condition persists. 70 Physical disk port has failed or cannot operate at the configured channel speed. 71 Mirror Race recovery failed for logical drive. 72 Controller parameters checksum verification failed - restored default. 75 Online firmware upgrade has failed. 78 Battery backup unit charger error. 79 Battery will not hold a charge. 80 Firmware entered unexpected state at run-time. 82 Check Consistency stopped on controller failure. 83 Foreground Init stopped on controller failure. 90 Channel is suspended due to some faults. 96 Device loop ID conflict (soft addressing) detected. 98 PD Clear failed. 101 Error. 102 Hot Spare SMART polling failed. 104 Reassign write operation failed. 105 Unrecoverable medium error during rebuild. 107 Unrecoverable medium error during recovery. 121 Bad block table on PD is full; unable to log blocks. 130 Consistency check / Make Data Consistent is cancelled. 131 Consistency check on logical drive error. 132 Consistency check / Make Data Consistent on logical drive failed. 133 Consistency check failed due to physical disk failure. 134 Logical drive has been made offline. 135 Logical drive is critical. 140 Rebuild on logical drive is cancelled. 141 Rebuild stopped with error. 142 Rebuild stopped with error. New physical disk failed. 143 Rebuild stopped because logical drive failed. 146 Logical drive initialization cancelled. 147 Logical drive initialization failed. 152 Expand capacity stopped with error. 153 Bad Blocks found. 156 Bad data blocks found. Possible data loss. 158 Attempt to read data from block that is marked in Bad Data Table. 159 Data for Disk Block has been lost due to Logical Drive problem. 160 Temporary-Offline RAID5/RAID3 array is available to the user again with the possibility of data loss in the array. 161 Temporary-Offline RAID0+1/RAID1/RAID0/JBOD array is available to the user again. 163 Reconstruct detected uncorrectable double medium errors. 165 Reconstuction resume failed due to configuration mismatch. 167 Marking LD inconsistent due to active writes at shutdown. 180 Logical drive background initialization failed. 182 Low battery charge level. Logical drive may have lost data. 183 Inconsistent data found during consistency check. 256 Fan failure. 258 Fan failure. 272 Power supply failure. 274 Power supply failure. 288 Over temperature. Temperature is above 70 degrees Celsius. 291 Over temperature. 304 Storage Works enclosure reported failure state. 305 Storage Works enclosure reported critical state. 309 Uninterruptible power supply battery low. 310 Uninterruptible power supply failed. 320 Fan failure. 323 Power supply failure. 326 Temperature is over safe limit. Failure imminent. 327 Temperature is above working limit. 330 Enclosure access critical. 332 Enclosure access is offline. 333 Enclosure soft addressing detected. 338 Physical disks in enclosure being spundown. 339 Temperature is below working limit. 340 Temperature is under safe limit. Failure imminent. 343 SIM failure. 346 Enclosure not supported; too many enclosures connected to port. 347 Enclosure firmware mismatch. 348 Sensor bad. 349 Enclosure phy bad. 350 SAS/SATA mixing not supported in enclosure; PD disabled. 385 Write back error. 388 Controller is dead. System is disconnecting from this controller. 391 Controller is gone. System is disconnecting from this controller. 393 Battery is bad. 395 Controller is gone. System is disconnecting from this controller. 398 Controller is gone. System is disconnecting from this controller. 403 Installation aborted. 404 Controller firmware mismatch. 405 The Battery Backup Unit is removed. 406 WARM BOOT failed. 410 Battery is not present. 414 Soft ECC error corrected. 415 Hard ECC error corrected. 418 BBU out of service. 423 Disabled partner. 425 Controller boot ROM image needs to be reloaded. 426 Controller is using default non-unique world-wide name. 427 Mirror Race recovery failed. 428 Mirror Race on critical logical drive. 431 Controller improperly shutdown! Data may have been lost. 433 Dual-active negotiation failed jumpers. 434 Dual-active negotiation failed IDs. 435 Dual-active negotiation failed board types. 436 Dual-active negotiation failed disk channels. 437 Dual-active negotiation failed host ports. 438 Dual-active negotiation failed memory size. 439 Dual-active negotiation failed cache memory size. 440 Error in Mirror Race Table. 441 A replacement controller attempted to stop the surviving controller. 447 Data in Cache not flushed during power up. 454 Cluster down; communication with peer lost. 457 Unable to recover cache data due to configuration mismatch. 464 Not enough controller memory. 470 Battery temperature is high. 473 Battery needs to be replaced. 474 Battery relearn timed out. 517 Lost connection to server, or server is down. 522 Battery test failed - battery bad 642 Back end SCSI bus dead. 644 Back end fibre dead. 811 Unable to recover cache data from TBBU. 960 SAS topology error: Loop detected. 961 SAS topology error: Unaddressable device. 962 SAS topology error: Multiple ports to the same SAS address. 963 SAS topology error: Expander error. 964 SAS topology error: SMP timeout. 965 SAS topology error: Out of route entries. 966 SAS topology error: Index not found. 967 SAS topology error: SMP function failed. 968 SAS topology error: SMP CRC error. 969 SAS topology error: Multiple subtractive. 970 SAS topology error: Table to table. 971 SAS topology error: Multiple paths.
MIB-OID:1.3.6.1.4.1.3183.1.1 (PET-MIB)
specific trap type message 65792 Temp Low Warning (OK -> Warning): (lower non Critical going low). 65794 Temp Low Critical(Warning -> Critical): (lower Critical going low). 65795 Temp Low Warning (Critical -> Warning): (lower Critical going high). 65796 Temp Low Critical(Critical -> NonRecover) (lower non recover going low). 65797 Temp Low Critical(NonRecover -> Critical) (lower non recover going high). 65799 Temp High Warning (OK -> Warning): (upper non Critical going high). 65800 Temp High Warning (Critical -> Warning): (upper Critical going low). 65801 Temp High Critical(Warning -> Critical): (upper Critical going high). 65802 Temp High Critical(NonRecover -> Critical): (upper non recover going low). 65803 Temp High Critical(Critical -> NonRecover): (upper non recover going high). 65921 Temp Low Warning (OK -> Warning): (lower non Critical going high). 65922 Temp Low Warning (Critical -> Warning): (lower Critical going low). 65923 Temp Low Critical(Warn -> Critical): (lower Critical going high). 65924 Temp Low Critical(NonRecover -> Critical) (lower non recover going low). 65925 Temp Low Critical(Critical -> NonRecover) (lower non recover going high). 65926 Temp High Warning (OK -> Warning): (upper non Critical going low). 65928 Temp High Critical(Warning -> Critical): (upper Critical going low). 65929 Temp High Warning (Critical -> Warning): (upper Critical going high). 65930 Temp High Critical(Critical -> NonRecover): (upper non recover going low). 65931 Temp High Critical(NonRecover -> Critical): (upper non recover going high). 66049 Thermal trip. 131328 Voltage Low - Warning (OK -> Warning): (lower non Critical going low). 131330 Voltage Low - Critical(Warning -> Critical): (lower Critical going low). 131332 Voltage Low - Critical(Critical -> NonRecover) (lower non recover going low). 131333 Voltage Low - Critical(NonRecover -> Critical) (lower non recover going high). 131335 Voltage High - Warning (OK -> Warning): (upper non Critical going high). 131337 Voltage High - Critical(Warning -> Critical): (upper Critical going high). 131338 Voltage High - Critical(NonRecover -> Critical): (upper non recover going low). 131339 Voltage High - Critical(Critical -> NonRecover): (upper non recover going high). 131457 Voltage Low - Warning (OK -> Warning): (lower non Critical going high). 131459 Voltage Low - Critical(Warning -> Critical): (lower Critical going high). 131460 Voltage Low - Critical(NonRecover -> Critical) (lower non recover going low). 131461 Voltage Low - Critical(Critical -> NonRecover) (lower non recover going high). 131462 Voltage High - Warning (OK -> Warning): (upper non Critical going low). 131464 Voltage High - Critical(Warning -> Critical): (upper Critical going low). 131466 Voltage High - Critical(Critical -> NonRecover): (upper non recover going low). 131467 Voltage High - Critical(NonRecover -> Critical): (upper non recover going high). 131841 Voltage Failed (digital assert sensor). 132097 Voltage Failed (digital predictive sensor). 132352 Voltage within limit. 132353 Voltage limit exceeded. 132609 Voltage performance lags. 196864 Current Low Warning (lower non Critical going low). 196866 Current Critical Low (lower Critical going low). 196868 Current Low Damage (lower non recover going low). 196869 Current no longer Damage but Critical Low (lower non recover going high). 196871 Current High Warning (upper non Critical going high). 196873 Current High Critical (upper Critical going high). 196874 Current no longer Damage but Critical High (upper non recover going low). 196875 Current High Damage (upper non recover going high). 196993 Current Low Warning (lower non Critical going high). 196995 Current Critical Low (lower Critical going high). 196996 Current no longer Damage but Critical Low (lower non recover going low). 196997 Current Low Damage (lower non recover going high). 196998 Current High Warning (upper non Critical going low). 197000 Current Critical High (upper Critical going low). 197002 Current High Damage (upper non recover going low). 197003 Current no longer Damage but Critical High (upper non recover going high). 197377 Current Failed. 197633 Current predictive Fail. 197888 Current within limit. 197889 Current limit exceeded. 198145 Current performance lags. 262400 Fan Pre-Fail (OK -> Warn): (lower non Critical going low). 262402 Fan Failed (Warn -> Critical): (lower Critical going low). 262403 Fan Pre-Fail(Critical -> Warn): (lower Critical going high). 262404 Fan Failed (Critical -> NonRecover) (lower non recover going low). 262405 Fan Failed (NonRecover -> Critical) (lower non recover going high). 262529 Fan Pre-Fail(OK -> Warn): (lower non Critical going high). 262530 Fan Pre-Fail(Critical -> Warn): (lower Critical going low). 262531 Fan Failed (Warn -> Critical): (lower Critical going high). 262532 Fan Failed (NonRecover -> Critical) (lower non recover going low). 262533 Fan Failed (Critical -> NonRecover) (lower non recover going high). 262913 Fan Failed. 263169 Fan predictive failure asserted. 263681 Fan performance lags. 356096 Chassis Intrusion (opened). 459777 CPU Predictive Failure. 487168 CPU internal error. 487169 CPU thermal trip failure. 487170 CPU failed built-in selftest; disabled (FRB1). 487171 CPU hung during POST; disabled (FRB2). 487172 CPU startup/initialization failure; disabled (FRB3). 487173 CPU configuration error. 487174 Uncorrectable CPU-complex error. 487178 CPU throttled (start). 552705 Power supply Aux/DC power fail. 552706 Power supply predictive failure asserted. 552707 Power supply input lost (AC/DC). 552708 Power supply input lost or out-of-range. 552709 Power supply input out-of-range, but present. 552710 Power supply configuration error. 592641 Power unit redundancy lost. 592645 Power unit: insufficient resources. 618244 Power Unit - A/C lost. 618245 Power Unit - Soft Power Control failure. 618246 Power Unit failure. 618247 Power Unit predictive failure. 787457 Memory - PDA event Module. 789249 Memory: Redundancy lost. 789253 Memory: Non-redundant: insufficient resources. 814849 Memory - Multi-bit error. 814850 Memory - Parity error. 814853 Memory - error logging limit reached. 814855 Memory - configuration error. 880385 DiskDrive: Drive Fault. 880386 DiskDrive: Predictive Failure. 880389 DiskDrive: In Critical Array . 880390 DiskDrive: In Failed Array. 884485 DiskDrive: Offline. 884486 DiskDrive: Failed. 884487 DiskDrive: Dead. 884489 DiskDrive: Prefail. 945920 POST - Memory Resized/Config changed. 1011456 POST - Error. 1011457 POST - System Firmware HANG. 1142529 Watchdog: OS Watchdog Reset. 1142530 Watchdog: OS Watchdog Shutdown. 1142531 Watchdog: OS Watchdog Power Down. 1142532 Watchdog: OS Watchdog Power Cycle. 1142533 Watchdog: OS Watchdog NMI/Diagnostic Int.. 1142534 Watchdog: OS Watchdog Status Expired. 1208066 Undetermined system hardware failure. 1273600 Front Panel NMI / Diagnostic Interrupt. 1273601 Bus timeout. 1273602 I/O channel check NMI. 1273603 Software NMI. 1273604 PCI PERR. 1273605 PCI SERR. 1273606 EISA Failsafe timer expired. 1273607 Correctable bus error. 1273608 Uncorrectable bus error. 1273609 Fatal NMI (Port 61h Bit 7). 1772038 PCI Interconnect: Slot Degraded. 1772040 PCI Interconnect: Slot Install Error. 2125568 Stop during OS load / initialization. 2125569 Run-time Stop. 2125570 OS Graceful Critical Stop. 2191104 PCI Hot Plug Slot fault asserted. 2191111 PCI Hot Plug Slot Interlock asserted (latch not closed). 2322176 Watchdog: Timer Expired. 2322177 Watchdog: Hard Reset. 2322178 Watchdog: Power Down. 2322179 Watchdog: Power Cycle. 2322180 Watchdog: Hardware Watchdog expired. 2322184 Watchdog: Timer Interrupt. 2649857 Controller access degraded or unavailable. 2649858 Management Controller off-line. 2649859 Management Controller unavailable. 2715393 Battery failed. 2719490 BBU on RAID Ctrl. battery low. 2719493 BBU on RAID Ctrl. failed. 14577411 Memory module error. 14577412 Memory module failed. 14577413 Memory module prefailure. 14746625 Memory: Predictive Failure (PDA) Module. 14774017 FSC: Memory module replaced. 14774018 FSC: Fatal general memory error. 14774022 FSC: Fatal CRC memory error. 14774024 FSC: Fatal thermal memory error. 14905090 FSC: No usable CPU. 14970624 FSC: System configuration Data error. 14970625 FSC: Resource Conflict. 14970626 FSC: IRQ not configured. 14970627 FSC: Device node allocation error. 14970628 FSC: Expansion ROM Slot not initialized. 15101697 FSC: Fan failed. 15101698 FSC: Fan pre-failure. 15101699 FSC: Redundant fan failed. 15232770 FSC: Redundant power supply Failed. 15232771 FSC: Redundant power supply AC fail. 15232772 FSC: Redundant power supply DC fail. 15232773 FSC: Redundant power supply Critical. Temp.. 15298432 FSC: Power supply redundancy lost.
MIB-OID:1.3.6.1.4.1.7933 (FASTTRAK.MIB)
specific trap type message 2 ECC Error on Disk 3 Disk Set Down by Driver 4 Disk Offline 10 Array Offline 11 Array Critical 14 Media Error on Disk 16 Rebuild Aborted 17 Sync. Aborted 18 ECC Fix Failed
