The following are the incompatible commands of Redundant Line Control function from the previous version.
create/modify sub-command
By specifying "_none _" with the -p option, it is possible to set a not used ping response monitoring of the HUB monitoring.
Before modification
"_none_" cannot be specified for -p option.
After modification
"_none_" can be specified for -p option.
Two monitoring destinations can be specified using -p option for the virtual interface of single physical interface configuration.
Before modification
Only one monitoring destination can be specified using -p option for the virtual interface of single physical interface configuration.
After modification
Up to two monitoring destinations can be specified using -p option for the virtual interface of single physical interface configuration.
modify sub-command
The monitoring destination settings can be changed while the virtual interface remains active.
Before modification
For changing the monitoring destination settings, the virtual interface state must be inactive.
After modification
Monitoring destination settings can be changed while the virtual interface state is active.
print sub-command
When ping response monitoring is not used, "_none_" is displayed in the Hostname parameter.
Before modification
Only the host name or IP address is indicated in the Hostname parameter.
After modification
Host name, IP address or "_none_" is displayed in the Hostname parameter.
# /opt/FJSVhanet/usr/sbin/hanetpoll print
Polling Status = OFF
interval(idle) = 5( 60) sec
time = 5 times
link detection = YES
FAILOVER Status = YES
Name HUB Poll Hostname
+-------+--------+------------------------------------------------------+
sha0 OFF _none_ |
The repair_time parameter will no longer be displayed.
Before modification
The repair_time parameter is displayed.
# /opt/FJSVhanet/usr/sbin/hanetpoll print
Polling Status = OFF
interval(idle) = 5( 60) sec
time = 5 times
repair_time = 5 sec
link detection = YES
FAILOVER Status = YES
Name HUB Poll Hostname
+-------+--------+------------------------------------------------------+
sha0 OFF 192.168.70.100,192.168.70.101 |
After modification
The repair_time parameter is not displayed.
# /opt/FJSVhanet/usr/sbin/hanetpoll print
Polling Status = OFF
interval(idle) = 5( 60) sec
time = 5 times
link detection = YES
FAILOVER Status = YES
Name HUB Poll Hostname
+-------+--------+------------------------------------------------------+
sha0 OFF 192.168.70.100,192.168.70.101 |
on sub-command
When disabling all the monitoring of the HUB monitoring function, message is indicated when the HUB monitoring function is started.
Before modification
All the monitoring of the HUB monitoring function cannot be disabled.
After modification
When disabling all the monitoring of the HUB monitoring function, the message below is displayed during the startup of HUB monitoring function.
hanet: 00100: The virtual interface is excluded from HUB monitoring. |
It is not necessary to stop monitoring by hanetpoll off command when applying the changes of monitoring parameter.
Before modification
It is necessary to stop monitoring by hanetpoll off command when applying the changes of monitoring parameter.
After modification
It is not necessary to stop monitoring by hanetpoll off command when applying the changes of monitoring parameter.
The -b option (recovery monitoring period settings of HUB monitoring) is obsoleted.
Before modification
The not used -b option existed.
After modification
The -b option is obsoleted.
devparam sub-command
The repair_time parameter will no longer be displayed.
Before modification
The repair_time parameter is displayed.
# /opt/FJSVhanet/usr/sbin/hanetpoll devparam
[ Standard Polling Parameter ]
Polling Status = ON
interval(idle) = 5( 60) sec
time = 5 times
repair_time = 5 sec
link detection = YES
FAILOVER Status = YES
[ Polling Parameter of each interface ]
Name intvl idle time repar link Fover
+-------+-----+-----+-----+-----+-----+-----+---------------------------+
sha0 2 60 5 5 YES YES |
After modification
The repair_time parameter is not displayed.
# /opt/FJSVhanet/usr/sbin/hanetpoll devparam
[ Standard Polling Parameter ]
Polling Status = ON
interval(idle) = 5( 60) sec
time = 5 times
link detection = YES
FAILOVER Status = YES
[ Polling Parameter of each interface ]
Name intvl idle time - link Fover
+-------+-----+-----+-----+-----+-----+-----+---------------------------+
sha0 2 60 5 --- YES YES |
[Contents 1]
When not setting the ping response monitoring, "----" will be displayed in the Primary Target/Secondary Target parameter.
[Changes 1]
Before modification
Host name or IP address is displayed in the Primary Target/Secondary Target parameter.
After modification
Host name, IP address or "----" is displayed in the Primary Target/Secondary Target parameter.
# /opt/FJSVhanet/usr/sbin/dsppoll Polling Status = ON interval(idle) = 5( 60) times = 5 link detection = YES FAILOVER Status = YES Status Name Mode Primary Target/Secondary Target HUB-HUB +------+------+----+-------------------------------------------+-------+ ON sha0 d ----(ON)/----(WAIT) OFF |
[Contents 2]
The repair_time parameter will no longer be displayed.
[Changes 2]
Before modification
The repair_time parameter is displayed.
# /opt/FJSVhanet/usr/sbin/dsppoll Polling Status = ON interval(idle) = 5( 60) times = 5 repair_time = 5 link detection = YES FAILOVER Status = YES Status Name Mode Primary Target/Secondary Target HUB-HUB +------+------+----+-------------------------------------------+-------+ ON sha0 d 192.168.70.100(ON)/192.168.70.101(WAIT) ACTIVE |
After modification
The repair_time parameter is not displayed.
# /opt/FJSVhanet/usr/sbin/dsppoll Polling Status = ON interval(idle) = 5( 60) times = 5 link detection = YES FAILOVER Status = YES Status Name Mode Primary Target/Secondary Target HUB-HUB +------+------+----+-------------------------------------------+-------+ ON sha0 d 192.168.70.100(ON)/192.168.70.101(WAIT) ACTIVE |
