3.5.1 Creation of Tier Pool

The items which can be specified to the Tier pool are as follows.

Basic Configuration Items of Tier Pool

Item	Specification (*1)	Explanation
Tier Pool Name	Required	This is a name of the Tier pool to be created. This name must be unique across all the ETERNUS Disk storage system registered in Storage Cruiser. Any alphanumeric character (1 - 16 characters), a hyphen (-), an underscore (_), and a pound symbol (#) may be specified. The letters to be specified are not case sensitive.
Policy Name	Optional	Specify the Tiering policy to associate with the Tier pool that is being created. Make a selection from the Tiering policies that have been defined and are displayed in the pull-down list. (*2)
Warning Threshold of Pool	Optional	To monitor the available capacity of the Tier pool, specify a threshold (%) of the usage rate of the Tier pool as a decimal figure in the range of 5 - 99. The default setting is "90". Specify a value that is greater than Caution Threshold of Pool. When this threshold is exceeded, a warning is notified by the SNMP Trap. When the usage rate of the Tier pool exceeds 90 %, the Tier pool can be used but evaluation and relocation cannot be completed properly.
Caution Threshold of Pool	Optional	To monitor the available capacity of the Tier pool, specify a threshold (%) of the usage rate of the Tier pool as 0 or as a decimal figure in the range of 5 - 80. The default setting is "75". Specify a value that is less than Warning Threshold of Pool. When this threshold is exceeded, a caution is notified by the SNMP Trap. When "0" is specified or the Set no Caution Threshold of pool checkbox is checked on, the value of this item is disabled.
Encryption Status	Required	Specify whether to make the Tier pool being created an encrypted Tier pool. The default setting is "No" (do not encrypt). When setting this as an encrypted Tier pool, select "Yes".
Specify Assigned CM	Optional	As needed, specify the CM which takes charge of the Tier pool being created. The checkbox is not checked by default (a CM in charge is not specified). To specify a CM which takes charge of the Tier pool, check the checkbox. All of the CMs present on the storage device are displayed, make a selection from these.
Number of Layers	Optional	Specify the number of layers of the Tier pool that is being created. 2 or 3 may be selected. The default setting is "2". (*2)
Disk Selection	Optional	Specify the disk selection method for configuring the sub-pool. "Auto" (automatic selection) or "Manual" (manual selection) can be selected. The default setting is "Auto". If "Auto" is selected, in the screen for configuring the Low sub-pool, the Middle sub-pool, and the High sub-pool, the required minimum capacity must be specified for each sub-pool. If "Manual" is selected, in the screen for configuring the Low sub-pool, the Middle sub-pool, and the High sub-pool, the disks for configuring each sub-pool must be specified.

*1: When a specification is omitted for the item of which specification is "Optional", a default value is configured.
*2: This cannot be specified when creating a one layer Tier pool.

Configuration Items of Sub-Pool

If "Auto" is selected for Disk Selection in "Basic Configuration Items of Tier Pool":

Item	Specification (*1)	Explanation
FTSP Name	Optional	Specify a name (that is unique within the ETERNUS SF system) for the sub-pool. Any alphanumeric character (1 - 16 characters), a hyphen (-), an underscore (_), and a pound symbol (#) may be specified. The letters to be specified are not case sensitive.
Disk Type	Required	Specify the type of disk for configuring the sub-pool. Make a selection from the disk types (Online, Nearline, SSD, SED-SAS, Online SED, Nearline SED, and SSD SED) that are displayed in the pull-down list.
Reliability	Required	Specify the RAID level of the sub-pool. Make a selection from one of the following that are displayed in the pull-down list: High Performance(RAID1+0) High Capacity(RAID5) High Reliability(RAID6) High Reliability(RAID6-FR) Mirroring(RAID1) Striping(RAID0)
Select Disks	Optional	When "High Reliability (RAID6-FR)" is selected for Reliability, specify one of the following methods for automatically selecting RAID group disks for configuring the sub-pool: Minimize number of using disks Prioritize rebuild rate When a level other than "High Reliability (RAID6-FR)" is selected for Reliability, this item does not need to be specified.
Minimum Required Capacity	Required	Specify the minimum capacity required for the sub-pool. A capacity of 1 MB or more may be specified. It is also possible to enter a decimal value. A drive is automatically selected in accordance with the RAID group specification and a sub-pool greater than or equal to the specified capacity is created. If the firmware version of the storage device is V10L70 or later The maximum capacity that can be created for the sub-pool is displayed in the format "(MAX: maximumCapacityToBeCreated)". For example, if the maximum capacity that can be created for the sub-pool is 2 PB, this is displayed as "(MAX: 2PB)". Specify a value less than or equal to the displayed capacity for this item.
Specify Assigned CM	Optional	Only when a CM in charge has been specified for Specify Assigned CM of "Basic Configuration Items of Tier Pool", as needed, specify the CM which takes charge of the RAID group configuring the sub-pool. The checkbox is not checked by default (a CM in charge is not specified). Any CM in charge can be configured from the CM in charge specified to the Tier pool. To specify a CM in charge, check the checkbox. All of the CMs specified for Specify Assigned CM of "Basic Configuration Items of Tier Pool" are displayed, make a selection from these. Up to 2 CMs may be specified.

*1: When a specification is omitted for the item of which specification is "Optional", a default value is configured.

If "Manual" is selected for Disk Selection in "Basic Configuration Items of Tier Pool":

Item	Specification (*1)	Explanation
FTSP Name	Optional	Specify a name (that is unique within the ETERNUS SF system) for the sub-pool. Any alphanumeric character (1 - 16 characters), a hyphen (-), an underscore (_), and a pound symbol (#) may be specified. The letters to be specified are not case sensitive.
Disk Type	Required	Specify the type of disk for configuring the sub-pool. Make a selection from the disk types (Online, Nearline, SSD, SED-SAS, Online SED, Nearline SED, and SSD SED) that are displayed in the pull-down list.
Reliability	Required	Specify the RAID level of the sub-pool. Make a selection from one of the following that are displayed in the pull-down list: High Performance(RAID1+0) High Capacity(RAID5) High Reliability(RAID6) High Reliability(RAID6-FR) Mirroring(RAID1) Striping(RAID0)
Fast Recovery Configuration	Optional	When selecting "High Reliability(RAID6-FR)" for Reliability, select Fast Recovery configuration. Creating RAID groups based on the number of disks for the specified configuration is required. When a level other than "High Reliability(RAID6-FR)" is selected for Reliability, this item does not need to be specified.
Disk	Required	Specify the disk of the RAID group that configures the sub-pool. The number of disks required differs depending on the reliability and Fast Recovery configuration of the RAID group.
Stripe Depth	Optional	Specify the size (KB) per disk in 1 stripe of the RAID group configuring the sub-pool. The default setting is "64". The stripe depth that can be specified depends on Reliability and the number of disks of the RAID group. High Performance(RAID1+0): 64/128/256/512/1024 High Capacity(RAID5) (from 2D+1P to 4D+1P): 64/128/256/512 High Capacity(RAID5) (from 5D+1P to 8D+1P): 64/128/256 High Capacity(RAID5) (from 9D+1P to 15D+1P): 64/128 High Reliability(RAID6): 64 High Reliability(RAID6-FR): 64 Mirroring(RAID1): Cannot be specified Striping(RAID0): 64/128/256/512/1024
Specify Assigned CM	Optional	Only when a CM in charge has been specified for Specify Assigned CM of "Basic Configuration Items of Tier Pool", as needed, specify the CM which takes charge of the RAID group configuring the sub-pool. The checkbox is not checked by default (a CM in charge is not specified). Any CM in charge can be configured from the CM in charge specified to the Tier pool. To specify a CM in charge, check the checkbox. All of the CMs specified for Specify Assigned CM of "Basic Configuration Items of Tier Pool" are displayed, make a selection from these. Up to 2 CMs may be specified.

*1: When a specification is omitted for the item of which specification is "Optional", a default value is configured.

Refer to "Create Tier Pool" in the ETERNUS SF Web Console Guide for information on how to create a Tier pool.

Point

Multiple Tier pools can be created in one ETERNUS SF system.
Only one Tiering policy can be configured to one Tier pool.
The chunk size that is set for a Tier pool is determined based on the maximum pool capacity of a storage device.
The chunk size of the Tier pools that have already been created cannot be changed.

It is also possible to recycle the made Tier pool having registered the storage device. Refer to "3.5.2 Recycling of Tier Pool Made in Storage Device" for details.