This section describes the operation on Model upgrade for ETERNUS Disk storage system on the Web Console.
Before Applying | After Applying | Operation |
|---|---|---|
ETERNUS DX60 | ETERNUS DX80 | |
ETERNUS DX80 S2 | ETERNUS DX90 S2 | |
ETERNUS DX410 S2 | ETERNUS DX440 S2 | |
ETERNUS DX80 S2/DX90 S2 | ETERNUS DX410 S2/DX440 S2 | Refer to "Operation on Model Upgrade for ETERNUS DX80 S2/DX90 S2 to DX410 S2/DX440 S2". |
ETERNUS DX60 S3 | ETERNUS DX100 S3 | |
ETERNUS DX100 S3 | ETERNUS DX200 S3 | |
ETERNUS DX500 S3 | ETERNUS DX600 S3 | |
ETERNUS DX8700 S3 | ETERNUS DX8900 S3 |
Operation on Model Upgrade for ETERNUS DX60 to DX80, for ETERNUS DX80 S2 to DX90 S2, for ETERNUS DX410 S2 to DX440 S2
Use the following procedure for applying Model upgrade options:
If Advanced Copy is in progress, stop Advanced Copy processing.
Apply Model upgrade options for ETERNUS Disk storage system.
Perform the following steps on the Web Console:
Reload the latest information about ETERNUS Disk storage system. Refer to "7.1.9 Reload ETERNUS Disk Storage System Configuration Information" for details.
Delete the license registered with ETERNUS Disk storage system. Refer to "7.7.3 Delete License" for details.
Register the license with ETERNUS Disk storage system. Refer to "7.7.1 Register License" for details.
Note
The device model name after applying Model upgrade options is displayed as "nameAfterApplyingModelUpgradeOptions"/"nameBeforeApplyingModelUpgradeOptions".
When you reload configuration information of the device which is applied Model upgrade options to ETERNUS DX440 S2, make sure that the license of the old device is registered.
In the following cases, you cannot reload configuration information.
When all of the licenses for the device which is applied Model upgrade options to ETERNUS DX440 S2 are deleted.
When no license is registered with the device which is applied Model upgrade options to ETERNUS DX440 S2.
When you cannot reload configuration information since all of the licenses are deleted, provisionally register the license of the old device. Then, reload configuration information of the device.
Operation on Model Upgrade for ETERNUS DX80 S2/DX90 S2 to DX410 S2/DX440 S2
Use the following procedure for applying Model upgrade options:
If Advanced Copy is in progress, stop Advanced Copy processing.
If Automated Storage Tiering has already been started for Tier pools, stop it for all the Tier pools. If a Tier pool with two or more layers exists, record the Tiering policy name for the Tier pool and the values set for level of each sub-pool in the Tier pool.
Perform the following steps on the Web Console:
Delete the license registered with ETERNUS Disk storage system. Refer to "7.7.3 Delete License" for details.
Delete ETERNUS Disk storage system. Refer to "7.1.3 Delete ETERNUS Disk Storage System" for details.
Apply Model upgrade options for ETERNUS Disk storage system.
Perform the following steps on the Web Console:
Register the upgraded ETERNUS Disk storage system. Refer to "7.1.1 Register ETERNUS Disk Storage System" for details.
Register the license with the upgraded ETERNUS Disk storage system. Refer to "7.7.1 Register License" for details.
If you have used the Advanced Copy function before applying Model upgrade options, reconfigure the connection type for ETERNUS Disk storage system. Refer to "7.11.2 Configure Connection Type for ETERNUS Disk Storage System" for details.
If you used Automated Storage Tiering, refer to "Recycling of Tier Pool Made in Storage Device" in the ETERNUS SF Storage Cruiser Operation Guide for Optimization Function to recycle Tier pools that exist in the ETERNUS Disk storage system. For the Tiering policy name and level of sub-pools for the Tier pool, specify the same values as those recorded in step 2. On completion of settings, start Automated Storage Tiering for the Tier pool.
Note
A serial number of ETERNUS Disk storage system may change after applying Model upgrade options. If you apply Model upgrade options without deleting ETERNUS Disk storage system, ETERNUS SF may not recognize the new ETERNUS Disk storage system.
In this case, delete the new ETERNUS Disk storage system and re-register it.
If you apply Model upgrade options for ETERNUS Disk storage system without deleting the license, the screen displays the license list for the old device. To display the license list for the new device, delete all of the registered licenses and update the screen.
Register the license after displaying the license list for the new device.
Operation on Model Upgrade for ETERNUS DX60 S3 to DX100 S3, for ETERNUS DX100 S3 to DX200 S3, for ETERNUS DX500 S3 to DX600 S3, for ETERNUS DX8700 S3 to DX8900 S3
Use the following procedure for applying Model upgrade options:
If Advanced Copy is in progress, stop Advanced Copy processing.
Apply Model upgrade options for ETERNUS Disk storage system.
Perform the following steps on the Web Console:
Reload the latest information about ETERNUS Disk storage system. Refer to "7.1.9 Reload ETERNUS Disk Storage System Configuration Information" for details.
Delete the license registered with ETERNUS Disk storage system. Refer to "7.7.3 Delete License" for details.
Register the license with ETERNUS Disk storage system. Refer to "7.7.1 Register License" for details.
Note
The device model name after applying Model upgrade options is displayed as "nameAfterApplyingModelUpgradeOptions"/"nameBeforeApplyingModelUpgradeOptions".
When you reload configuration information of the device which is applied Model upgrade options, make sure that the license for the device model before applying Model upgrade options is registered.
In the following cases, you cannot reload configuration information.
When all of the licenses for the device which is applied Model upgrade options are deleted.
When no license is registered with the device which is applied Model upgrade options.
When you cannot reload configuration information since all of the licenses are deleted, provisionally register the license of the old device. Then, reload configuration information of the device.
