This section describes the messages generated by the Server Link Common command and Client Link Common command. And these messages are common with the following commands:
File Control Command
Application Execution Command
Client Power Control Command
[Description]
The disk runs out of space.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify disk space availability.
[Target Commands]
Server Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
End other applications.
[Target Commands]
Server Link Common Command
[Description]
Cannot start the Server Task Link engine (Systemwalker MpNjsosv service) is in the process of stopping.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Wait till the Server Task Link engine is restarted, and then re-execute.
[Target Commands]
Server Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be error in registry information.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Startup process of thread failed.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to create a temporary file for the management file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be error in registry information.
[Parameter]
YYY: System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
The requested process cannot be started as the schedule process is initializing.
[Parameter]
YYY: System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Wait for a moment and carry out the process again.
[Target Commands]
Server Link Common Command
[Description]
Failed to create a temporary file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check free space on the install directory of this software.
[Target Commands]
Server Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to create the thread for executing the requested process.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to open the temporary file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Server Link Common Command
[Description]
Failed to write to the temporary file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Server Link Common Command
[Description]
Failed to read the temporary file.
[Parameter]
YYY : System error code notified by the Task Link command.
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Server Link Common Command
[Description]
Failed to open the log information output file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Server Link Common Command
[Description]
Failed to write to the log information output file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Server Link Common Command
[Description]
Failed to read the log information output file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Server Link Common Command
[Description]
Failed to load message resource module "F3csjmsc.dll".
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
[Target Commands]
Server Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Aborted the process of command request by canceling the command during processing in the server Task Link engine (Systemwalker MpNjsosv service).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check the network setting.
[Target Commands]
Server Link Common Command
[Description]
There is insufficient heap space.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Process interrupts.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to generate the thread.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Startup process of thread failed.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There is insufficient heap space.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
A failure may have occurred in network devices.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Version in the Task Link command differs from that of the Server Task Link engine (Systemwalker MpNjsosv service).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Version level in the Task Link command differs from that of the Server Task Link engine (Systemwalker MpNjsosv service).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to acquire socket (SOCK_STREAM).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check the installation status of network.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to acquire socket (SOCK_STREAM).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to create the heap space.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to free the file search handle.
[Parameter]
YYY : System error code notified by the Task Link command.
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to free the file creation handle.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There is insufficient heap space.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to free memory from local heap.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
A failure may have occurred in network devices.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Version in the Task Link command differs from that of Server Task Link engine (Systemwalker MpNjsosv service).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Version level in the Task Link command differs from that of Server Task Link engine (Systemwalker MpNjsosv service).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Received invalid data (packet).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
A failure may have occurred in network devices.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Received invalid data (packet).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
A failure may have occurred in network devices.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Different users have attempted to simultaneously access the same computer running Windows operating systems.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Use the same user name when connecting to the computer running Windows operating systems. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Investigate the jobs that are running concurrently, and check whether users with different user names attempt to connect to the same computer running Windows operating systems.
[Target Commands]
Server Link Common Command
[Description]
The specified path/directory is invalid. Check the specified path.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
A file/directory path specified in the parameter of Task Link command is invalid. Set an existing path correctly in the parameter, and then execute the command again.
[Target Commands]
Server Link Common Command
[Description]
The specified file is not found.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
A file specified in the parameter of Task Link command cannot be found. Set an existing file/directory path correctly in the parameter, and then execute the command again.
[Target Commands]
Server Link Common Command
[Description]
The specified directory is not found.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
A directory specified in the parameter of Task Link command cannot be found. Set an existing directory path correctly in the parameter, and then execute the command again.
[Target Commands]
Server Link Common Command
[Description]
The specified directory already exists.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
A directory specified in the parameter of Task Link command already exists. Choose another directory, and then execute the command again.
[Target Commands]
Server Link Common Command
[Description]
The specified file already exists.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
With the file rename, set the file name again so that the file with the same name does not exist as the destination file name, and then execute the command again.
[Target Commands]
Server Link Common Command
[Description]
The file specified by the path does not exist.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
The path name specified in the parameter of Task Link command is not a file name. Set the path name in the parameter so that it is a file name, and then execute the command again.
[Target Commands]
Server Link Common Command
[Description]
The directory specified by the path does not exist.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
The path name specified in the parameter of Task Link command is not a directory name. Set the path name in the parameter so that it is a directory name, and then execute the command again.
[Target Commands]
Server Link Common Command
[Description]
Failed to get the information of transfer source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of transfer source file. If this symptom occurs randomly, contact your system administrator.
[System Administrator Response]
In case of local drive, check the settings of permissions.
In case of network drive, check the network status.
If the symptom occurs randomly, check the DNS status during periods of failure. Also check if other job or application is simultaneously gaining access to that computer through other user.
If you cannot determine the cause, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to get the information of the transfer destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of the transfer destination file. If the symptom occurs randomly, contact your system administrator.
[System Administrator Response]
In case of local drive, check the settings of permissions.
In case of network drive, check the network status.
If the symptom occurs randomly, check the DNS status during periods of failure. Also check if other job or application running simultaneously is gaining access to that computer through other user.
If you cannot determine the cause, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to read the transfer source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of transfer source file.
[Target Commands]
Server Link Common Command
[Description]
Failed to read the transfer destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of transfer destination file.
[Target Commands]
Server Link Common Command
[Description]
Failed to search the specified path.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check specified path.
[Target Commands]
Server Link Common Command
[Description]
Failed to connect to the shared directory.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check a shared name, user name, and password. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check the network status. If the symptom occurs randomly, check the DNS status during periods of failure and if other job or application running simultaneously is gaining access to that computer through other user.
If you cannot determine the cause, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to transfer file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified transfer source and destination path.
[Target Commands]
Server Link Common Command
[Description]
Failed to delete the file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified file path.
[Target Commands]
Server Link Common Command
[Description]
Failed to rename the file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified file path.
[Target Commands]
Server Link Common Command
[Description]
Failed to create directory.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified directory path.
[Target Commands]
Server Link Common Command
[Description]
Failed to delete the directory.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified directory path.
[Target Commands]
Server Link Common Command
[Description]
Failed to start application on the server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified file path.
[Target Commands]
Server Link Common Command
[Description]
The heap area runs out of disk space because the maximum limit of files that can be handled by the Task Link command at one time has been reached.
The maximum number of files that can be handled by the Task Link command at one time is as follow:
For the Server Task Link
It is up to 500 files, which includes the files handled by other Server Task Link command that is concurrently running.
For the Client Task Link
It is up to 500 files within the same client, which includes the files handled by the Client Task Link command that is concurrently running.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Perform one of the following actions or both of actions so that the maximum number of files that can be handled by the Task Link command is less than or equal to 500, and then execute again.
Divide the number of files that you handle by using the Task Link command to multiple times.
If there are files to be concurrently handled by other Task Link command, stagger the timing of handling process by other Task Link command.
[System Administrator Response]
Restart the system.
If the problem is not resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to open the transfer source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of transfer source file.
[Target Commands]
Server Link Common Command
[Description]
Failed to open the transfer destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of transfer destination file.
[Target Commands]
Server Link Common Command
[Description]
Failed to write to the transfer destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of transfer destination file.
[Target Commands]
Server Link Common Command
[Description]
Failed to load DLL required for RAS control.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
[Target Commands]
Server Link Common Command
[Description]
Failed to unload DLL required for RAS control.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to log on to the computer.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified user name/password. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check whether right of "logon as service" is set for user specified by server application start command.
[Target Commands]
Server Link Common Command
[Description]
Failed to connect to the Internet while operating FTP file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Failed to log on to the FTP server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check FTP server name/user name/password. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check the following:
The status of the FTP server
The firewall settings (whether the connection passes through a firewall)
The login settings for the FTP server (whether settings, such as user lock settings, have been made so that the specified user cannot log in to the FTP server)
Note that the user name and the name of the FTP server can be checked using the messages that are output at the same time as this message.
[Target Commands]
Server Link Common Command
[Description]
Failed to create a directory on the FTP server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified directory path. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check if access limits are set for the directory specified on the FTP server.
[Target Commands]
Server Link Common Command
[Description]
Failed to delete a directory on the FTP server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified directory path. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check if access limits are set for the directory specified on the FTP server.
[Target Commands]
Server Link Common Command
[Description]
Failed to delete a file on the FTP server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified file path. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check if access limits are set for the file or directory specified on the FTP server.
[Target Commands]
Server Link Common Command
[Description]
Failed to send a file to the FTP server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified transfer source path or transfer destination path. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check if access limits are set for the file or directory specified on the FTP server.
[Target Commands]
Server Link Common Command
[Description]
Failed to receive file from FTP server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified transfer source path or transfer destination path. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check if access limits are set for the file or directory specified on the FTP server.
[Target Commands]
Server Link Common Command
[Description]
Cannot start the requested process because the communication controller section of the Server Task Link engine (Systemwalker MpNjsosv service) has started the stop process.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Wait till the Sever Task Link engine is restarted, and then re-execute.
[Target Commands]
Server Link Common Command
[Description]
Forcibly terminated the process in the communication control section of the Server Task Link engine (Systemwalker MpNjsosv service).
[Parameter]
YYY : System error code notified by the Task Link command
[Target Commands]
Server Link Common Command
[Description]
Memory required for file compression/decompression process is not enough.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
End other applications.
[Target Commands]
Server Link Common Command
[Description]
Memory required for file compression/expansion process is not enough.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
End other applications on the client system specified in the parameter of Server Task Link command.
[Target Commands]
Client Link Common Command
[Description]
Failed to create a temporary file for file compression/expansion process.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the drive specified for the compression/decompression destination is available, or the drive has sufficient space. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check the drive's status specified as the compression/expansion destination.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Failed to read temporary file in the process of file compression/expansion.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the drive specified for the compression/expansion destination is available, or the drive has sufficient space. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check the drive's status specified for the compression/expansion destination.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Failed to write to the temporary file in the process of file compression/expansion.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the drive specified for the compression/expansion destination is available, or the drive has sufficient space.
If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check the drive's status specified as the compression/expansion destination.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Check the compression source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the file specified to be compressed is correct or it is not being used by other application.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Check compression source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Check compression source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Server Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Restart the client system specified in the parameter of Server Task Link command.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Check the compression destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the file specified to be compressed is correct or it is not being used by other applications.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Check the compression destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the compression destination file is writable or it is not being used by other applications.
[Target Commands]
Server Link Common Command
Client Link Common Command
[Description]
Check compression destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Check the expansion source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the file specified to be expanded is correct or it is not being used by other applications.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Check the expansion source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the file specified to be expanded is correct or it is not being used by other applications.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Check the expansion source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Check the expansion source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Server Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
File that cannot be expanded is specified.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the source file to be expanded was correctly compressed by the compression program.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Expansion process could not be carried out as the file to be expanded is destroyed.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the source file to be expanded was correctly compressed by compression program.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Check the expanded file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the file specified to be expanded is correct or if it is not being used by other applications.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Check expansion destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the file specified to be expanded is not write protected or if it is not being used by other applications.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Check the expansion destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command (Windows only)
Client Link Common Command
[Description]
Forcibly terminated the process in the link library of the Server Task Link engine (Systemwalker MpNjsosv service).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[Target Commands]
Server Link Common Command
[Description]
Forcibly terminated the process in the link library of the Client Task Link engine (Systemwalker MpNjsosv service).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check network installation.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the Client Task Link function running on the client specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Check the network installation on each terminal having the Operation Manager server and the Client Task Link service installed.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check network installation.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check the network installation on each terminal having the Operation Manager server and the Client Task Link service installed.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Insufficient heap area
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Insufficient heap
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the Client Task Link function running on the client specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Restart the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be some error in registry information.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Registry information may be abnormal.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall the Client Task Link on the client specified in the parameter of Client Task Link command.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Restart the server-target client.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Restart the server-target client.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to connect to Server Task Link engine.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Verify that the Systemwalker MpNjsosv service is active. If not, start the service. Verify the network settings are correct. Also check if there is a TCP/IP port conflict between other applications.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Client Task Link is not active on the client specified in the parameter of Client Task Link command or there may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check that the Client Task Link is active on the client specified in the parameter of Client Task Link command. Also check that the network settings are correct or there is a TCP/IP port conflict between other applications.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Server Task Link engine (Systemwalker MpNjsosv service) may be in the process of ending, or may have ended.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-execute the command after restarting Server Task Link engine (Systemwalker MpNjsosv service).
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
The Client Task Link engine may be in the process of ending, or may have ended.
[Parameter]
YYY : System error code notified by the Task Link command.
[System Action]
Terminates the process.
[User Response]
Re-execute the command after restarting the Client Task Link engine.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command.
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Restart the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Restart the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
The Server Task Link engine (Systemwalker MpNjsosv service) may not be working normally or there may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check that the Server Task Link engine is working normally. Also, check the installation status of network.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
The Client Task Link may not be active on the client specified in the parameter of Client Task Link command, or there may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the Client Task Link on the client specified in the parameter of Client Task Link command. Contact the System Administrator if the problem is not resolved.
[System Administrator Response]
Restart the client specified in the parameter of Client Task Link command. And then, start the Client Task Link. Also, check the installation status of the client's network.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
The Client Task Link engine may not be working normally.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check that the Client Task Link engine is working normally. Also, check the installation status of the client's network.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
The Server Task Link engine (Systemwalker MpNjsosv service) is not working normally, or there may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check that the Server Task Link engine (Systemwalker MpNjsosv service) is working normally. Check the network installation status.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
The Client Task Link is not active on the client specified in the parameter of Client Task Link command, or there may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the Client Task Link on the client specified in the parameter of Client Task Link command. Contact System Administrator if the problem is not resolved.
[System Administrator Response]
Restart the client specified in the parameter of Client Task Link command. And then, start the Client Task Link. Also, check the installation status of the client's network.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
The Client Task Link may not be working normally, or there may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command.
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check that the Client Task Link is working normally. Also, check the installation status of the client's network.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command.
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Restart the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Re-execute the Task Link command. Contact System Administrator if the problem is not resolved.
[System Administrator Response]
Check that Server Task Link engine (Systemwalker MpNjsosv service) is working normally. Also, check the network installation status.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check that the Server Task Link engine (Systemwalker MpNjsosv service) is working normally. Also check the installation status of the client's network.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your System Administrator.
[System Administrator Response]
Check that the Client Task Link is working normally. Also, check the installation status of the client's network.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact the System Administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact the System Administrator.
[System Administrator Response]
Restart the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There is insufficient heap space.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There is insufficient heap space.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Restart the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command.
[System Action]
Terminates the process.
[User Response]
Close unneeded programs on the server. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Close unneeded programs on the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be an error in the registry information.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software on the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be an error in the registry information.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall this software on the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be an error in the registry information.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Re-install this software.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There may be an error in the registry information.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall this software on the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Restart the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Restart the server.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Process was stopped by aborting the command.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[Target Commands]
Server Link Common Command
[Description]
In response to the user's request, the process is suspended.
[Parameter]
YYY : System error code notifying the Task Link command
[System Action]
Process is stopped.
[Target Commands]
Client Link Common Command
[Description]
Parameter is invalid for the requested process.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check whether parameter characters are correct. Also, check whether the specified entry name is the same as the name registered in the system.
[Target Commands]
Server Link Common Command
[Description]
Unsupported option is specified.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
A command of different version level has been installed. Re-install this software.
[Target Commands]
Server Link Common Command
[Description]
RAS control runs out of local heap.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
Dialup network service is not installed.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Install the dialup network service.
[Target Commands]
Server Link Common Command
[Description]
Failed to unload "RASAPI32.DLL" in RAS control.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
With RAS connection, a line connection failed or a connection was rejected.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that an entry name/user name/password/domain name is correct.
Check the telephone number if /PN: or /CN: is specified.
Set the retry if the line is being used.
If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Verify that the telephone number specified in the entry can be used normally.
Verify that a proper modem is selected for the entry or remote access server
Check the setting of user and call back that was specified on the remote access server of connection destination computer.
Check the protocol setting in the entry or on the remote access server of connection destination computer.
[Target Commands]
Server Link Common Command
[Description]
Failed to disconnect RAS connection. It may be already disconnected.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check that a RAS connection is specified in the entry. Or check that it is disconnected by other job or application.
[Target Commands]
Server Link Common Command
[Description]
The RAS control runs out of memory.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Server Link Common Command
[Description]
RAS connection being invalid cannot be disconnected.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the RAS connection is used according the specified entry. Also, check that the RAS connection is disconnected by other job or application.
[Target Commands]
Server Link Common Command
[Description]
Disconnecting a RAS connection was requested, but the RAS connection cannot be found.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the RAS connection is used according the specified entry. Also, check that the RAS connection is disconnected by other job or application.
[Target Commands]
Server Link Common Command
[Description]
The disk runs out of space.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Terminates the process.
[System Administrator Response]
Verify disk space availability.
[Target Commands]
Client Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
End other applications.
[Target Commands]
Client Link Common Command
[Description]
Cannot start the requested process as the Client Task Link engine is in the process of stopping.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Start the Client Task Link on the client system specified in the parameter of Client Task Link command, and then re-execute the command.
[Target Commands]
Client Link Common Command
[Description]
Cannot start the requested process as the Client Task Link engine is in the process of stopping.
[Parameter]
YYY :System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Start the Client Task Link on the client system specified in the parameter of Client Task Link command, and then re-execute the command.
[Target Commands]
Client Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be an error in the registry information.
[Parameter]
System error code notified by the Task Link command.
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall the Client Task Link service on the client specified in the parameter of Client Task Link command.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to start the thread.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to create a temporary file for the manager file.
[Parameter]
YYY :System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall the Client Task Link on the client specified in the parameter of Client Task Link command.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be an error in the registry information.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall the Client Task Link on the client specified in the parameter of Client Task Link command.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be an error in the registry information.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall the Client Task Link on the client specified in the parameter of Client Task Link command.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
The requested process cannot be started as the schedule process is initializing.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Wait for a moment and carry out the process again.
[Target Commands]
Client Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to create the thread for executing the requested process.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to open a temporary file
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Client Link Common Command
[Description]
Failed to write to the temporary file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Client Link Common Command
[Description]
Failed to read a temporary file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Client Link Common Command
[Description]
Failed to open the log information output file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Client Link Common Command
[Description]
Failed to write to the log information output file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Client Link Common Command
[Description]
Failed to read the log information output file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check if access limits are set for the installation directory of this software.
[Target Commands]
Client Link Common Command
[Description]
Aborted the process of command request by canceling the command during processing in the Client Task Link.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check the network setting.
[Target Commands]
Client Link Common Command
[Description]
There is insufficient heap space.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to create the thread.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu systems engineer.
[Target Commands]
Client Link Common Command
[Description]
Failed to create the thread.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu system engineer.
[Target Commands]
Client Link Common Command
[Description]
Failed to start the thread.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu systems engineer.
[Target Commands]
Client Link Common Command
[Description]
Failed to start the thread.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu system engineer.
[Target Commands]
Client Link Common Command
[Description]
Heap is exhausted.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu systems engineer.
[Target Commands]
Client Link Common Command
[Description]
Heap is exhausted.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu systems engineer.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu system engineer.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu systems engineer.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu systems engineer.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu systems engineer.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu systems engineer.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the object client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Contact your Fujitsu systems engineer.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check the network status. Contact the Fujitsu's Engineer if the problem is not resolved.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check the network status. Contact the Fujitsu's Engineer if the problem is not resolved.
[Target Commands]
Client Link Common Command
[Description]
The version of Task Link command and Client Task Link engine differs.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall the Client Task Link in the object client. Contact your Fujitsu systems engineer if the problem is not resolved.
[Target Commands]
Client Link Common Command
[Description]
The version of Task Link command and Client Task Link engine differs.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall the Client Task Link in the object client. Contact your Fujitsu systems engineer if the problem is not resolved.
[Target Commands]
Client Link Common Command
[Description]
Version level of the Task Link command and Client Task Link engine differs.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall the Client Task Link in the object client. Contact your Fujitsu systems engineer if the problem is not resolved.
[Target Commands]
Client Link Common Command
[Description]
Version level of the Task Link command and Client Task Link engine differs.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall the Client Task Link in the object client. Contact your Fujitsu systems engineer if the problem is not resolved.
[Target Commands]
Client Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to get the socket (SOCK_STREAM).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Check the network installation status of the client system, which is specified in the parameter of Client Task Link command.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to get the socket (SOCK_STREAM).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to create the heap space.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to release the file search handle.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to release the file search handle.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There is insufficient heap space.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to release the memory for the local heap.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There is not enough memory available.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not solved, contact your system administrator.
[System Administrator Response]
Collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
There may be a network problem.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
A failure may have occurred in network devices.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
The version differs in the Task Link command and the Client Task Link.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall the Client Task Link on the client system specified in the parameter of Client Task Link command.
If the problem is not resolved, contact your Fujitsu systems engineer.
[Target Commands]
Client Link Common Command
[Description]
The version level differs in the Task Link command and the Client Task Link.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Reinstall the Client Task Link on the client system specified in the parameter of Client Task Link command.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Received invalid data (packet).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
A failure may have occurred in network devices.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Received invalid data (packet).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
A failure may have occurred in network devices.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Different users have attempted to simultaneously access the same computer running Windows operating systems.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Use the same user name when connecting to the computer running Windows operating systems. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
Investigate the jobs that are working concurrently, and verify that a user with different user name may connect to the same computer running Windows operating systems.
[Target Commands]
Client Link Common Command
[Description]
The specified file/directory path is invalid.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
A file/directory path specified in the parameter of Task Link command is invalid. Set an existing path correctly in the parameter, and then execute the command again.
[Target Commands]
Client Link Common Command
[Description]
Specified file cannot be found.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
A file specified in the parameter of Task Link command cannot be found. Set an existing file/directory path correctly in the parameter, and then execute the command again.
[Target Commands]
Client Link Common Command
[Description]
The specified directory cannot be found.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
A directory specified in the parameter of Task Link command cannot be found. Set an existing directory path correctly in the parameter, and then execute the command again.
[Target Commands]
Client Link Common Command
[Description]
The specified directory already exists.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
A directory specified in the parameter of Task Link command already exists. Choose another directory, and then execute the command again.
[Target Commands]
Client Link Common Command
[Description]
Specified file already exists.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
With the file rename, set the file name again so that the file with the same name does not exist as the destination file name, and then execute the command again.
[Target Commands]
Client Link Common Command
[Description]
The specified path name is not the file name.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
The path name specified in the parameter of Task Link command is not a file name. Set the path name in the parameter so that it is a file name, and then execute the command again.
[Target Commands]
Client Link Common Command
[Description]
Specified path name is not the directory name.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
The path name specified in the parameter of Task Link command is not a directory name. Set the path name in the parameter so that it is a directory name, and then execute the command again.
[Target Commands]
Client Link Common Command
[Description]
Failed to get the information of the transfer source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of transfer source file. If this symptom occurs randomly, contact your system administrator.
[System Administrator Response]
In case of local drive, check the settings of permissions.
In case of network drive, check the network status.
If the symptom occurs randomly, check the DNS status during periods of failure. Also check if other job or application is simultaneously gaining access to that computer through other user.
If you cannot determine the cause, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to get the information of transfer destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of transfer destination file. If this symptom occurs randomly, contact your system administrator.
[System Administrator Response]
In case of local drive, check the settings of permissions.
In case of network drive, check the network status.
If the symptom occurs randomly, check the DNS status during periods of failure. Also check if other job or application is simultaneously gaining access to that computer through other user.
If you cannot determine the cause, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to read the transfer source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of transfer source file.
[Target Commands]
Client Link Common Command
[Description]
Failed to read the transfer destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of transfer destination file.
[Target Commands]
Client Link Common Command
[Description]
Failed to search the specified path.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified path.
[Target Commands]
Client Link Common Command
[Description]
Failed to connect to the shared directory.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check a shared name, user name, and password. If the problem is not resolved, contact your system administrator.
[System Administrator Response]
A failure may have occurred in network devices.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to transfer the file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified transfer source path or transfer destination path.
[Target Commands]
Client Link Common Command
[Description]
Failed to delete the file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified file path.
[Target Commands]
Client Link Common Command
[Description]
Failed to rename a file name.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified file path.
[Target Commands]
Client Link Common Command
[Description]
Failed to create a directory.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified directory path.
[Target Commands]
Client Link Common Command
[Description]
Failed to delete a directory.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified directory path.
[Target Commands]
Client Link Common Command
[Description]
Failed to start an application.
[Parameter]
YYY : Error code of system notified by Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified file path.
Specify an executable application file (with an extension of exe or bat) in the /ae parameter.
Files with extension txt or wsf are executed by an application that is associated with the extension by Windows.
The name of the executable application is notepad.exe with files with extension txt and WScript.exe with files with extension wsf.
To start c:\data\data1.txt of client "hostname" using Notepad:
#/opt/FJSVsnjss/bin/execacli hostname /ae:c:\\windows\\notepad.exe c:\\data\\data1.txt
In this case, the current directory during execution is c:\windows.
[Target Commands]
Client Link Common Command
[Description]
There may be a time difference between the server setting and client setting.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Review the time setting of the client. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Review the time setting of the server.
[Target Commands]
Client Link Common Command
[Description]
The specified application process did not end within the timeout (seconds) specified in the "/we:" option of application startup command (execacli).
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Increase the value specified in the /we: option.
Verify that the application process can be completed within the specified timeout.
Delete the option setting in "/we:" if it is specified for the application operations, such as including screen operation, which may take an arbitrary time to complete.
[Target Commands]
Client Link Common Command
[Description]
There is insufficient heap space to create the tree information used for file operations.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Divide the entire process of the file that is processed at one time, into several processes, and execute again.
[System Administrator Response]
Restart the system.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
The computer that requested the process cannot be found.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Verify that the target client name is specified correctly.
Verify that the client Task Link on the relevant client is active.
Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Check if the target host name is registered in the HOSTS file of the server running DNS or jobs.
[Target Commands]
Client Link Common Command
[Description]
Failed to open the transfer source file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of the transfer source file.
[Target Commands]
Client Link Common Command
[Description]
Failed to open the transfer destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of the transfer destination file.
[Target Commands]
Client Link Common Command
[Description]
Failed to write to the transfer destination file.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the status of the transfer destination file.
[Target Commands]
Client Link Common Command
[Description]
Failed to connect to Internet during FTP file operations.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Contact your system administrator.
[System Administrator Response]
Restart the client system specified in the parameter of Client Task Link command. If the problem is not resolved, contact your system administrator.
If the problem cannot be resolved, collect the data of the following functions by using Maintenance Information Collection tool, and contact your Fujitsu systems engineer.
Server Task Link
Client Task Link
Depending on the options you selected during installation, one of the above functions may not exist. In that case, collect only the data of function that you can select.
[Target Commands]
Client Link Common Command
[Description]
Failed to log on to the FTP server
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the FTP server name/user name/password. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Check the following:
The status of the FTP server
The firewall settings (whether the connection passes through a firewall)
The login settings for the FTP server (whether settings, such as user lock settings, have been made so that the specified user cannot log in to the FTP server)
Note that the user name and the name of the FTP server can be checked using the messages that are output at the same time as this message.
[Target Commands]
Client Link Common Command
[Description]
Failed to create a directory on the FTP server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified directory path. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Check if access limits are set for the directory specified on the FTP server.
[Target Commands]
Client Link Common Command
[Description]
Failed to delete a directory on the FTP server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified directory path. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Check if access limits are set for the directory specified on the FTP server.
[Target Commands]
Client Link Common Command
[Description]
Failed to delete a file on the FTP server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified file path. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Check if access limits are set for the directory specified on the FTP server.
[Target Commands]
Client Link Common Command
[Description]
Failed to send a file to the FTP server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified send source path and send destination path. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Check if access limits are set for the file or directory specified on the FTP server.
[Target Commands]
Client Link Common Command
[Description]
Failed to receive a file from the FTP server.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified send source path and send destination path. Contact your system administrator if the problem is not resolved.
[System Administrator Response]
Check if access limits are set for the file or directory specified on the FTP server.
[Target Commands]
Client Link Common Command
[Description]
Need to have shutdown privilege.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Log on again as a user with shutdown privilege on the target client.
[Target Commands]
Client Link Common Command
[Description]
Check the status of the computer to be shut down.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check if a message asking if saving the active program data is displayed on the client. If it is unnecessary to wait for the active program data to be saved, specify /EF option.
[Target Commands]
Client Link Common Command
[Description]
Cannot start the requested process because the communication controller section of the Client Task Link has started the stop process.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Start the Client Task Link on the target client, and then re-execute.
[Target Commands]
Client Link Common Command
[Description]
Aborted the process of command request by canceling the command during processing in the communication control section of the Client Task Link.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[Target Commands]
Client Link Common Command
[Description]
There is an error in the application name specified in the /AE option.
[Parameter]
YYY : System error code notified by the Task Link command
[System Action]
Terminates the process.
[User Response]
Check the specified application name. If a space is included in the application name that you start, enclose the application name in double quotation marks ("").
[Target Commands]
Client Link Common Command
