The table below lists and describes the error messages (code type 2) output to the command prompt.
Message ID | Message Text | Meaning | User Response |
|---|---|---|---|
20000 | The command was executed by a user other than an administrator. | The command was executed by a user who is not a member of the "Administrators" group. | Log in as a member of the "Administrators" group, then execute the command. |
20001 | The number of defined virtual network adapters exceeds the maximum limit. | The number of virtual adapters defined by the -n option of the hanetconfig command exceeds the maximum allowed value. | Check the number of defined virtual adapters. The maximum number of virtual adapters that you can specify is 16. |
20002 | The specified physical network adapter does not exist. | The physical adapter specified in the option of the command cannot be found. | Check that the adapter name is correct and try again. If necessary, link the adapter to TCP/IP and try again. Else, if you have specified an adapter that is bundled in a currently active virtual adapter, deactivate that virtual adapter and try again. |
20003 | The specified virtual network adapter name is already in use. | You cannot specify this name for the virtual adapter because a virtual adapter of the same name already exists. | Check that the name is correct, then try again. |
20004 | The specified virtual adapter name does not exist. | No virtual adapter of the specified name exists. The operation cannot be executed. | Check that the name is correct, then try again. |
20005 | The specified VLAN ID is incorrect. | Check that the VLAN ID is correct and try again. For more details, refer to "1.3 System Requirements for GLS." | |
20006 | The specified physical network adapter is already in a partial share with another virtual network adapter. | The specified physical adapter is already in a partial share with another virtual adapter. | Specify a different physical adapter. |
20007 | An identical physical network adapter was specified. | The specified physical adapter is already specified for this virtual adapter. | You cannot bundle identical physical adapters in a virtual adapter. Specify a different physical adapter. |
20008 | A virtual network adapter with the same VLAN ID is already configured. | Set a unique VLAN ID for the virtual adapter to be additionally defined, then try again. | |
20009 | Cannot start the operation because configuration is not complete. | Cannot start the operation because configuration is not complete. | Finish making settings using the hanetconfig command, then try again. |
20010 | Cannot start the operation because GLS is already installed. | Cannot start the operation because GLS is already installed. | - |
20011 | Cannot start the operation because the virtual network adapter is being activated. | You cannot execute this operation because the virtual adapter is being activated. | Deactivate the virtual adapter using the stphanet command, then try again. |
20012 | The specified parameter value is incorrect. | The specified parameter value is incorrect. | Refer to "Chapter 6 Command Reference," then try again. |
20013 | Failed to communicate with the driver. | Failed to communicate with the GLS driver. | Check that the GLS driver is installed and try again. |
20014 | Failed to get information from the registry. | Failed to get GLS setting information from the registry. | Try again. If the error repeats, delete the GLS settings then try again. |
20015 | Failed to write to the registry. | Failed to write GLS settings to the registry. | Try again. If the error repeats, delete the GLS settings then try again. |
20016 | Cannot start the operation because the virtual adapter is activated. | You cannot execute this operation because the virtual adapter is being activated. | Deactivate the virtual adapter using the stphanet command, then try again. |
20017 | Cannot start the operation because the virtual adapter is being deactivated. | You cannot execute this operation because the virtual adapter is deactivated. | Deactivate the virtual adapter using the stphanet command, then try again. |
20018 | Failed to activate. Execute the stphanet command. | Failed to activate. Execute the stphanet command. | Deactivate the virtual adapter using the stphanet command, then try again. |
20019 | Failed to deactivate. Re-execute the stphanet command. | Failed to deactivate. Re-execute the stphanet command. | Try again. |
20020 | Failed to activate. Re-execute the strhanet command. | Failed to activate. | Retry activation. |
20021 | Some virtual network adapter is activated. | You cannot execute this operation because some virtual adapters are activated. | Deactivate the virtual adapters using the stphanet command, then try again. |
20022 | The specified mac address is already in use. | You cannot specify this MAC address for the virtual adapter because another virtual adapter is already using the same MAC address. | Check the MAC address setting by executing the print subcommand of the hanetconfig command, then specify a different MAC address. |
20023 | The ping monitoring is not configured. | No settings have been made for ping monitoring. | Make the required settings using the hanetpoll command. |
20024 | The ping monitoring is already executed. | Ping monitoring is already started. | - |
20025 | The ping monitoring is already stopped. | Ping monitoring is already stopped. | - |
20026 | The specified IP address is invalid. | The specified IP address is invalid. | Specify a valid IP address. |
20027 | The specified ping monitoring target is already configured. | The specified ping monitoring target has already been specified. | Specify a different ping monitoring target. |
20028 | The specified ping monitoring target does not exist. | The specified ping monitoring target does not exist. | Check if the specified ping monitoring target is already specified by executing the print subcommand of the hanetpoll command. |
20029 | The product of the interval and the number of times to monitor exceeds 300 seconds. | The product of the ping interval and the number of pings exceeds 300. | Change the ping interval and the number of pings settings so that their product does not exceed 300. |
20030 | Cannot change settings while the ping monitor function is running. | You cannot change ping monitor settings while the ping monitor function is running. | Stop the ping monitor function by executing the hanetpoll command, then change the settings. |
20031 | The number of IP addresses to be monitored for a physical adapter exceeds the maximum limit of 3. | The number of IP addresses set within the same IP address list exceeds the maximum. | The number of ping target IP addresses that can be set within the same IP address list is limited to 3. Revise the ping target settings so that this maximum is not exceeded. |
20032 | The number of IP address lists to be monitored for a physical adapter exceeds the maximum limit of 3. | The number of IP address lists set for the same physical adapter exceeds the maximum. | The number of IP address lists that can be set per physical adapter is limited to 3. Revise the ping target settings so that this maximum is not exceeded. |
20033 | The adapter was switched because the ping monitor detected a failure. | The adapter was switched because the ping monitor function detected a network failure. | Execute the dsphanet command to check the status of the monitor target in which the failure was detected. |
20034 | The ping monitor detected a failure. | The ping monitor function detected a network failure. | Execute the dsphanet command to check the status of the monitor target in which the failure was detected. |
20035 | The adapter was restored. | The adapter is restored. | - |
20036 | Cannot operate the specified file. | Cannot operate the specified file. | Make sure that the specified file exists, then try again. |
20037 | The specified backup file is invalid. | The specified backup file is invalid. | Specify the backup file with the hanetbackup command, then try again. |
20038 | The primary adapter and the secondary adapter are the same. | The primary adapter and the secondary adapter are the same. | Specify different primary and secondary adapters, then try again. |
20039 | The number of bundled physical adapter exceeds the maximum limit. | The number of bundled physical adapter s exceeds the maximum limit. | Specify no more than two physical adapters to be bundled in a virtual adapter. |
20040 | Cannot switch adapter because virtual adapter bundles only one adapter. | Cannot switch adapters because virtual adapter bundles only one physical adapter. | Check the amount of defined physical adapters. |
20041 | Cannot switch adapter because standby adapter does not exist. | Cannot switch adapters because there is no standby adapter. | Run the dsphanet command to check physical adapter statuses. |
20042 | Cannot delete settings while the ping monitor function is configured. | Cannot delete settings while ping monitoring is active. | Deactivate ping monitoring before you can delete the settings. |
20043 | The service does not exist. | The service does not exist. | Check that the GLS service is displayed on the service screen of the administrator tool. |
20044 | Failed to control the service. | Failure of the service controller. | Check the Service screen of the administrator tool for the GLS service status. Then, try to run the command again. |
20045 | The service is not running. | The service is not running. | Retry after starting the GLS service. |
20046 | Failed to communicate with the service. | Failure in data communication with the service. | Check the Service screen of the administrator tool for the GLS service status. Then, try to run the command again. |
20047 | Failed to install the driver. | Failed to install the driver. | Close the Local Area Connection Properties screen, and then try to run the command again. |
20048 | Failed to uninstall the driver. | Failed to uninstall the driver. | Check that the driver is installed on the Local Area Connection Properties screen. Then, close the Properties screen and try to run the command again. |
20049 | The specified file does not exist. | The specified file does not exist. | Specify another file and try again. |
20050 | The specified directory does not exist. | The specified directory does not exist. | Specify another directory and try again. |
20051 | The virtual adapter is not configured. | The virtual adapter is not configured. | Make settings for the virtual adapter and try again. |
20052 | The ping monitor configuration is incomplete. | The ping monitor function could not be started, because the corresponding configuration data are incomplete. | Check the ping monitor configuration data using the hanetpoll command, and make ping monitor settings for all physical adapters before you try again. |
20053 | The specified physical network adapter is already used by other virtual network adapters. | The specified physical network adapter is already used by other virtual network adapters. | Specify another physical adapter. Note that a virtual adapter for Hyper-V cannot be shared with physical driver that is bundled by other virtual adapter. |
20054 | Virtual adapter for Hyper-V is not supported on this platform. | Virtual adapter for Hyper-V is not supported in this environment. | Create a virtual adapter other than virtual adapter for Hyper-V. Hyper-V supported environment is required to use commands and options for GLS' Hyper-V. |
20055 | The number of mac addresses exceeds the maximum limit. | The number of MAC addresses which can be specified exceeds the maximum limit. | The number of MAC addresses which can be specified at one time is limited to 128. Revise the settings so that this maximum is not exceeded. |
20056 | This command is not supported on this platform. | This command is not supported in this environment. | Check the environment. |
20057 | Cannot start the operation because operational adapter does not exist. | Cannot start the operation because operational adapter does not exist. | Run the dsphanet command to check physical adapter statuses. |
20058 | Cannot delete the specified physical adapter because it is not bundled in the virtual adapter. | Cannot start the operation because the specified physical adapter is not bundled in the virtual adapter. | Check that the physical adapter specified with the -t option is bundled in the virtual adapter specified with the -n option, referring to a result displayed by executing the print subcommand of the hanetconfig command. |
20059 | Cannot delete the physical adapter. | Cannot delete the specified physical adapter. | When the virtual adapter bundles one physical adapter, you cannot delete the physical adapter. Check the number of physical adapters bundled in the virtual adapter, referring to a result displayed by executing the print subcommand of the hanetconfig command. |
20060 | Cannot delete the specified physical adapter because it is operational. | Cannot delete an operational physical adapter. | For deleting an operational physical adapter, change the status of the adapter to standby with the change subcommand of the hanetnic command and then delete the adapter. |
20061 | Failed to add the physical adapter. Re-execute the hanetnic add command. | Failed to add the physical adapter to the virtual adapter. | Try again. |
20062 | Failed to delete the physical adapter. Re-execute the hanetnic delete command. | Failed to delete the physical adapter from the virtual adapter. | Try again. |
20063 | Cannot continue the process because the status of the virtual adapter is failure. | Cannot continue the process because the status of the virtual adapter is failure. | Deactivate the virtual adapter by executing the stphanet command, then try again. |
20064 | Failed to execute the command due to an internal error. | Failed to execute the command due to an internal error. | Try again. If the error repeats, restart the operating system, and then try again. |
20065 | Failed to add the physical adapter. Execute the hanetnic delete command. | Failed to add the physical adapter to the virtual adapter. | Delete the physical adapter from the virtual adapter with the delete subcommand of the hanetnic command, then try to add the physical adapter. |
29998 | Failed to communicate between components. | Failed to communicate between components. | Collect materials for examination of GLS, and tell Fujitsu SE an error message. For details on collecting diagnostic data, refer to "6.4.1 hanet_snap." |
29999 | An internal API failed. | An internal API failed. | Execute the stphanet command to forcibly stop the virtual adapter. |
