[Description]
The processing for setting up the environment has started.
[Corrective Measures]
This message simply indicates that the command has started, and no action is required.
[Description]
The processing for setting up the environment has been canceled.
[Corrective Measures]
This message simply indicates that the command has terminated, and no action is required.
[Description]
The processing for setting up the environment has terminated normally.
[Corrective Measures]
This message simply indicates that the command has terminated, and no action is required.
[Description]
The processing for deleting the environment has started.
[Corrective Measures]
This message simply indicates that the command has started, and no action is required.
[Description]
The processing for deleting the environment has been canceled.
[Corrective Measures]
This message simply indicates that the command has terminated, and no action is required.
[Description]
The processing for deleting the environment has terminated normally.
[Corrective Measures]
This message simply indicates that the command has terminated, and no action is required.
[Description]
The processing for updating the environment has started.
[Corrective Measures]
This message simply indicates that the command has started, and no action is required.
[Description]
The processing for updating the environment has been canceled.
[Corrective Measures]
This message simply indicates that the command has terminated, and no action is required.
[Description]
The processing for updating the environment has terminated normally.
[Corrective Measures]
This message simply indicates that the command has terminated, and no action is required.
[Description]
This message asks for confirmation about whether it is OK to start the command processing.
[Parameter]
%1: System name that has already been set up
[System Action]
The system waits for a response to be entered.
[Corrective Measures]
Enter "y" to reset the environment, otherwise enter "n".
[Description]
The environment has not been set up.
[System Action]
The system stops the command processing.
[Corrective Measures]
Execute this command only if the environment has already been set up.
[Description]
The number of arguments or argument keywords specified with the command is invalid.
[Parameter]
%1: Invalid number of arguments or argument keywords
[System Action]
The system stops the command processing.
[Corrective Measures]
Check the synopsis for the command that has been executed, by referring to "swidmg_set_ssoagent (Systemwalker Single Sign-On Agent Setup Command)" in the "Command Reference" section. Execute the command again after specifying the correct number of arguments in accordance with the synopsis.
[Description]
There is an error with an argument specified with the command.
[Parameter]
%1: Specified argument
[System Action]
The system stops the command processing.
[Corrective Measures]
Check the synopsis for the command that has been executed, by referring to "swidmg_set_ssoagent (Systemwalker Single Sign-On Agent Setup Command)" in the "Command Reference" section. 6.1.3 swidmg_set_ssoagent (Systemwalker Single Sign-On Agent Setup Command)Execute the command again after specifying the correct argument in accordance with the synopsis.
[Description]
An argument is specified more than once.
[Parameter]
%1: Duplicate argument
[System Action]
The system stops the command processing.
[Corrective Measures]
Check the synopsis for the command that has been executed, by referring to "swidmg_set_ssoagent (Systemwalker Single Sign-On Agent Setup Command)" in the "Command Reference" section. 6.1.3 swidmg_set_ssoagent (Systemwalker Single Sign-On Agent Setup Command)Execute the command again after eliminating any redundant options.
[Description]
A required argument is not specified.
[Parameter]
%1: Required argument
[System Action]
The system stops the command processing.
[Corrective Measures]
Check the synopsis for the command that has been executed, by referring to "swidmg_set_ssoagent (Systemwalker Single Sign-On Agent Setup Command)" in the "Command Reference" section. 6.1.3 swidmg_set_ssoagent (Systemwalker Single Sign-On Agent Setup Command)Execute the command again after adding the required argument.
[Description]
Only one instance of the Systemwalker Single Sign-On Agent setup command can run at a time. The command could not be started, because another instance of the command was already running.
[System Action]
The system stops the command processing.
[Corrective Measures]
Execute the command again after the command that is currently being executed has completed.
[Description]
You do not have the privileges to execute the Systemwalker Single Sign-on Agent setup command.
[System Action]
The system stops the command processing.
[Corrective Measures]
Execute the command again as a user with the following privileges.
Windows: Administrator privileges
UNIX: System administrator (superuser) privileges
[Description]
The specified password does not match the password specified in the business system setup file.
[System Action]
The system stops the command processing.
[Corrective Measures]
Check the password specified in the business system setup file, and then execute the command again.
[Description]
The processing for setting up the environment has failed.
[System Action]
The system stops the command processing.
[Corrective Measures]
This message indicates that the command has terminated abnormally. Take action based on the messages that were displayed before this message, and then execute the command again.
[Description
The processing for deleting the environment has failed.
[System Action]
The system stops the command processing.
[Corrective Measures]
This message indicates that the command has terminated abnormally. Take action based on the messages that were displayed before this message, and then execute the command again.
[Description]
The processing for updating the environment has failed.
[System Action]
The system stops the command processing.
[Corrective Measures]
This message indicates that the command has terminated abnormally. Take action based on the messages that were displayed before this message, and then execute the command again.
[Description]
Checking the existence of the directory or file indicated in the message has failed.
[Parameter]
%1: Path to the file or directory
[System Action]
The system stops the command processing.
[Corrective Measures]
Execute the command again after specifying the correct file or directory.
[Description]
Reading the definition file has failed.
[Parameter]
%1: File name
%2: Section name
%3: Key
[System Action]
The system stops the command processing.
[Corrective Measures]
Check whether the specified file path is correct, and also check whether the access permissions for the file have been set up.
If the problem still occurs even after the cause of the error has been removed, collect data using the Maintenance Information Collection Tool, and then contact Fujitsu technical support.
Refer to "How to Collect Maintenance Information" for details on how to collect maintenance information.Appendix A How to Collect Maintenance Information
[Description]
Writing the definition file has failed.
[Parameter]
%1: File name
%2: Section name
%3: Key
[System Action]
The system stops the command processing.
[Corrective Measures]
Check whether the specified file path is correct, and also check whether the access permissions for the file have been set up.
If the problem still occurs even after the cause of the error has been removed, collect data using the Maintenance Information Collection Tool, and then contact Fujitsu technical support.
Refer to "How to Collect Maintenance Information" for details on how to collect maintenance information.Appendix A How to Collect Maintenance Information
[Description]
Copying the file failed.
[Parameter]
%1: Source file
%2: Target file
%3: Error details
[System Action]
The system stops the command processing.
[Corrective Measures]
An error occurred while the command was being executed to copy from the source file to the target file.
The cause of the error is output to the "Error" field. Remove the cause of the error, and then execute the command again.
If the cause of the error is unknown, collect maintenance information and contact Fujitsu technical support.
Refer to "How to Collect Maintenance Information" for details on how to collect maintenance information.
[Description]
Setting access permissions for a file has failed.
[Parameter]
%1: File name
[System Action]
The system stops the command processing.
[Corrective Measures]
An error occurred while access permissions for the file were being set up. Check whether the command execution user can access the file indicated in the "File" field, and then execute the command again.
[Description]
Reading the business system setup file has failed.
[Parameter]
%1: File name
%2: Error details
[System Action]
The system stops the command processing.
[Corrective Measures]
Download the business system setup file again, and then execute the command again.
[Description]
The maximum number of business systems that can be set up has been exceeded.
[System Action]
The system stops the command processing.
[Corrective Measures]
Remove any unnecessary business systems, and then execute the command again.
[Description]
The process for obtaining a business system name from the settings file has failed.
[System Action]
The system stops the command processing.
[Corrective Measures]
Download the business system setup file again, and then execute the command again.
[Description]
Memory became insufficient while the Systemwalker Single Sign-On Agent was being set up.
[System Action]
The system stops the command processing.
[Corrective Measures]
Either install additional memory, or stop any unnecessary applications. Then, execute the command again.
[Description]
Reading the settings file has failed.
[Parameter]
%1: File name
%2: Error details
[System Action]
The system failed to read the settings file.
[Corrective Measures]
Download the business system setup file again, and then execute the command again.
[Description]
An internal error occurred during the processing.
[System Action]
The system stops the command processing.
[Corrective Measures]
Check whether the Systemwalker product has been installed correctly. Also, check whether the server has enough memory and disk space for the command to run. If the problem cannot be resolved, collect maintenance information and contact Fujitsu technical support.
Refer to "How to Collect Maintenance Information" for details on how to collect maintenance information.Appendix A How to Collect Maintenance Information
