Event traps are messages reported from a device. If you have any questions about the message contents, refer to the instruction manual for hardware to take corrective actions.
Depending on the event level, the corresponding icon may turn red (Error) or yellow (Warning).
(In case of the level "Information," the icon color is not changed.)
Failure event | Level | Event display |
|---|---|---|
Library hardware error | Error | Library system failed. Use the Remote Panel to check the error contents (FSC=xxxx, Sensekey=xxxx). |
Barcode reader error | Warning | Barcode reader in robot#number failed. |
CM error | Warning | An error occurred in media error(CM fail).(Barcode Label=xxxx) |
CAS cell error | Warning | CAS unit number error occurred. |
Cell error | Warning | Cell unit failed.(Barcode Label=xxxxx) |
CIC sensor error | Warning | CIC sensor in robot #number failed. |
Battery alarm | Warning | Battery unit in LCT#number failed. |
Shelf 0 fan alarm | Warning | Shelf FAN in LCT#0 failed. |
Shelf 1 fan alarm | Warning | Shelf FAN in LCT#1 failed. |
CAS open error | Warning | An open error occurred in CAS unit number |
FC/SCSI adapter card error | Warning | Adapter#number failed. |
Firmware BOOTUP alarm | Warning | The LCT#number bootup alarm occurred. |
EEPROM error | Warning | EEPROM failed. |
ROBOT PSU alarm | Warning | PSU unit in robot robot#number failed. |
ROBOT PSU power off alarm | Warning | Power-off occurred in PSU unit in robot#number. |
ROBOT PSU FAN alarm | Warning | PSU unit FAN in robot#number failed. |
Temperature alarm | Warning | The temperature in the library is abnormal.(temperature degree C). |
Temperature abnormality error | Error | Tape library temperature increased abnormally (temperature degrees C), leading to a library system fail. |
Vibration alarm | Warning | Library system detected an abnormal vibration. |
Humidity alarm | Warning | Tape library humidity (humidity %) is abnormal. |
LCT failover alarm | Warning | Failover occurred in LCT#number. |
LCT cutoff alarm | Warning | Cutoff occurred in LCT#number. |
ROBOT Down alarm | Warning | Robot#number failed. |
Front door open (during operation) | Warning | Front door of the library system was opened. |
Nearing no cleaning tape | Warning | The installed cleaning cartridges will reach a limit soon. |
Expired deadline for cleaning | Warning | Maximum number of uses of cleaning cell#number (barcode label: xxxx) was reached. |
Cleaning cartridge none | Warning | Cleaning cartridge is not available. |
ROBOT Serdes alarm | Warning | Serdes in robot#number failed. |
Power control card alarm | Warning | Power control card in LCT#number failed. |
LCD power off alarm | Warning | Power-off occurred in operation panel. |
Drive hardware error | Error | An error occurred in drive#number. Use the remote panel to check the error contents (FSC=xxxx, Sensekey=xxxxxx). |
Media error | Warning | An Error occurred in media error (barcode label:xxxxxx). |
Fan alarm | Warning | A FAN alarm occurred in drive #number. |
Cleaning request | Warning | Drive#number needs cleaning. Perform cleaning. |
Cluster PSU0 power off alarm | Warning | Power-off occurred in PSU0 in drive cluster#number. |
Cluster PSU1 power off alarm | Warning | Power-off occurred in PSU1 in drive cluster#number. |
Cluster PSU0 alarm | Warning | PSU0 in drive cluster#number failed. |
Cluster PSU1 alarm | Warning | PSU1 in drive cluster#number failed. |
LCT/DCT0 IF failure | Warning | Interface between LCT#number and DCI#0 (drive cluster#number) failed. |
LCT/DCT1 IF failure | Warning | Interface between LCT#number and DCI#1 (drive cluster#number) failed. |
DCT0 failure | Warning | DCI#number in drive cluster#number failed. |
DCT1 failure | Warning | DCI#number in drive cluster#number failed. |
Nearing Media Life | Warning | Media soon will be end of life (Barcode Label:xxxxx). |
Reach Media Life | Warning | Media reached at the end of life (Barcode Label:xxxxx). |
Reach ROBOT life | Warning | Robot#number reached at the end of life. |
Reach Drive Life | Warning | Drive#number reached at the end of life. |
