| ETERNUS SF AdvancedCopy Manager Message Guide 13.0 -Microsoft(R) Windows(R) 2000/Microsoft(R) Windows Sever(TM) 2003-, -Solaris-, -HP-UX-, -Linux-, -AIX- |
|
Contents
Index
|
This chapter explains the messages produced by the AdvancedCopy Manager cluster operation.
The cluster setup of the primary node has been completed. Next, create the cluster environment of the secondary node.
The cluster setup of the primary node has been completed.
The system ends processing.
In accordance with the procedure for creating a cluster environment, perform the next step.
The cluster setup of the secondary node has been completed.
The cluster setup of the secondary node has been completed.
The system ends processing.
In accordance with the procedure for creating a cluster environment, perform the next step.
The cluster deletion of the primary node has been completed.
The cluster deletion of the primary node has been completed.
The system ends processing.
In accordance with the procedure for deleting a cluster environment, perform the next step.
The cluster deletion of the secondary node has been completed. Next, delete the cluster environment of the primary node.
The cluster deletion of the secondary node has been completed.
The system ends processing.
In accordance with the procedure for deleting a cluster environment, perform the next step.
The cluster setup command or cluster unsetup command is already running.
The cluster setup command or cluster unsetup command is already running.
The system interrupts processing.
Verify that no other cluster setup command or cluster deletion command is running.
Failed to acquire information from the cluster file. Error Code = code, File Name = filename
Failed to acquire information from the cluster file.
code: Error code
filename: Cluster file name
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
No cluster environment setting file exists. File Name = filename
No cluster environment setting file exists.
filename: Cluster environment setting file name
The system interrupts processing.
[Solaris version]
[HP-UX version]
[Linux version]
[AIX version]
Verify that a correct mount point name is used for the shared disk.
Check the mount status of the shared disk.
[Windows version]
Contact a Fujitsu systems engineer.
The cluster setup has been completed.
The cluster setup has been completed.
The system interrupts processing.
Verify that the AdvancedCopy Manager logical node name or job name (service name) is not duplicated.
Verify that a AdvancedCopy Manager shared disk used in another cluster is not mounted.
Failed to acquire information from the registry information file. Error Code = code, File Name = filename
Failed to acquire information from the registry information file.
code: Error code
filename: Registry information file name
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
The processing was canceled.
The processing was canceled.
The system interrupts processing.
None.
A cluster system environment has been created in clustersystem.
A cluster system environment was already created in another cluster system.
clustersystem: Name of cluster system that has been created
SAFE: SynfinityCluster or PRIMECLUSTER
MSCS: MSCS
MCSG: MC/ServiceGuard
VCS : VERITAS Cluster Server
PRM : PRIMECLUSTER
HACM : High Availability Cluster Multi-Processing
The system interrupts processing.
Use the cluster setup command that supports the existing cluster system to create a cluster environment.
The number of nodes that can be registered is exceeded. Maximum Number of Nodes=number
The number of nodes that can be registered is exceeded.
number: Maximum number of cluster environments that can be registered
The system interrupts processing.
Unsetup other cluster environments and re-execute processing.
If no other cluster environments can be unsetuped, contact a Fujitsu systems engineer.
The cluster setup tool does not support this version of AdvancedCopy Manager.
The cluster setup tool does not support this version of AdvancedCopy Manager.
The system interrupts processing.
Check the version of AdvancedCopy Manager.
Failed to create a cluster environment on a shared disk. Error Code=code1-code2
Failed to create a cluster environment on a shared disk.
code1: Error code 1
code2: Error code 2
The system interrupts processing.
Verify that the shared disk can be used on the execution node.
The cluster environment creation command terminated with an error. Error Code = code1-code2, Package Name = name
The cluster environment creation command terminated with an error.
code1: Error code 1
code2: Error code 2
name: Package name of the command that terminated with an error
The system interrupts processing.
Set up the environment in accordance with an instruction for the package that terminated with an error.
For information on an instruction for the package, refer to the following:
[Solaris version]
[HP-UX version]
[Linux version]
[AIX version]
- Other: Message that was output before this message was output
[Windows version]
- FJSVswstf: work-directory\var\clset\clset_FJSVswstf.log
- FJSVswsts: work-directory\var\clset\clset_FJSVswsts.log
- FJSVswsrp: work-directory\var\clset\clset_FJSVswsrp.log
- FJSVswssc: work-directory\var\clset\clset_FJSVswssc.log
- PortServ: A message box that was output before this message was output
- DBSetUp: Contact a Fujitsu systems engineer.
- IISSetUp: work-directory\var\trc\alias.log
Failed to read the command definition file for creating a cluster environment.
Failed to read the command definition file for creating a cluster environment.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to set up information in the cluster file. Error Code = code1, File Name = filename
Failed to set up information in the cluster file.
code: Error code
filename: Cluster file name
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
The service name is already used in another cluster environment (nodename).
The service name (job name) was already being used in another cluster environment.
nodename: Name of AdvancedCopy Manager logical node that uses the service name (job name)
The system interrupts processing.
Check the service name
Failed to create a registry information file. Error Code = code1-code2
Failed to create a registry information file.
code1 :Error code
code2 :Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
The node name is in an invalid format.
The node name is in an invalid format.
The system interrupts processing.
Check the AdvancedCopy Manager logical node name.
The Storage management server has been constructed with another node name (nodename).
The Storage management server has been constructed with another AdvancedCopy Manager logical node name.
nodename: Name of AdvancedCopy Manager logical node constructed as a Storage management server service
The system interrupts processing.
Check the construction status of the Storage management server service.
The primary node has an environment constructed with another cluster system (cluster).
The primary node has an environment constructed with another cluster system.
cluster: Cluster system of the primary node
The system interrupts processing.
Construct an environment using the same command as that for the cluster system of the primary node.
The primary node has an environment constructed with another server type (servertype).
The primary node has an environment constructed with another server type.
servertype: Server type of the primary node
1: Storage management server
2: Storage server
The system interrupts processing.
Check the Storage server type.
The primary node has an environment constructed with another language (Language).
The primary node has an environment constructed with another language.
Language: Language type of the primary node
JAPANESE: Japanese version
ENGLISH: English version
The system interrupts processing.
Check the AdvancedCopy Manager language type.
The primary node has an environment constructed with another code (code).
The primary node has an environment constructed with another code.
code: Code of the primary node
The system interrupts processing.
Check the AdvancedCopy Manager code.
The primary node does not have a cluster environment.
The primary node does not have a cluster environment.
The system interrupts processing.
Construct a cluster environment for the primary node.
Verify that the mount point or disk resource is correct.
The primary node has an environment constructed with another version (version).
The primary node has an environment constructed with another version.
version: Version of the primary node
The system interrupts processing.
Check the AdvancedCopy Manager version.
The primary node has an environment constructed with another AFS type (AFSType).
The primary node has an environment constructed with another AFS type.
AFSType: AFS type
1: Non-AFS
2: AFS
The system interrupts processing.
Check the AdvancedCopy Manager AFS type.
No cluster environment has been created.
No cluster environment has been created.
The system interrupts processing.
Verify that a AdvancedCopy Manager cluster environment was created.
The command for unsetup the cluster environment terminated with an error. Error Code = code1-code2, Package Name = name
The command for unsetup the cluster environment terminated with an error.
code1: Error code 1
code2: Error code 2
name: Package name of the command that terminated with an error
The system interrupts processing.
Set up the environment in accordance with an instruction for the package that terminated with an error.
For information on an instruction for the package, refer to the following:
[Solaris version]
[HP-UX version]
[Linux version]
[AIX version]
- Other: A message that was output before this message was output
[Windows version]
- FJSVswstf: work-directory\var\clset\clset_FJSVswstf.log
- FJSVswsts: work-directory\var\clset\clset_FJSVswsts.log
- FJSVswsrp: work-directory\var\clset\clset_FJSVswsrp.log
- FJSVswssc: work-directory\var\clset\clset_FJSVswssc.log
- PortServ: A message box that was output before this message was output
- DBSetUp: Contact a Fujitsu systems engineer.
- IISSetUp: work-directory\var\trc\alias.log
The cluster environment of the secondary node has not been deleted.
The cluster environment of the secondary node has not been deleted.
The system interrupts processing.
After deleting the cluster environment of the secondary node, re-execute processing.
Execute processing after deleting the cluster environment of all secondary nodes in cluster operation.
Failed to clear the cluster file. Error Code = code, File Name = path
Failed to clear the cluster file.
code: Error code
path: Cluster file path
The system continues processing.
Although the cluster environment was deleted, refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to delete the cluster file. Error Code = code1-code2, File Name = path
Failed to delete the cluster file.
code1: Error code 1
code2: Error code 2
path: Cluster file path
The system continues processing.
Although the cluster environment was deleted, refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Deletion of the cluster in forced mode has been completed.
Deletion of the cluster in forced mode has been completed.
The system ends processing.
In accordance with the procedure for deleting a cluster environment, perform the next step.
No cluster environment with the node name (name) has been created.
No cluster environment with the node name (name) has been created.
name: Specified AdvancedCopy Manager logical node name
The system interrupts processing.
Check the AdvancedCopy Manager logical node name.
The node was not deleted.
The node was not deleted.
The system interrupts processing.
After deleting the node, reexecute processing.
The cluster file does not exist. File Name = path
The cluster file does not exist.
path: Cluster file pathname
The system interrupts processing.
[Solaris version]
[HP-UX version]
[Linux version]
[AIX version]
Check the mount status of the shared disk.
[Windows version]
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to restore the registry information file. Error Code = code
Failed to restore the registry information file.
code: Error code
The system continues processing.
Although the cluster environment was deleted, refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
The secondary node has a cluster environment.
The secondary node has a cluster environment.
The system interrupts processing.
Verify that the mount point or disk resource is correct.
The primary node has a cluster environment constructed with the logical node (node).
The primary node has a cluster environment constructed with the logical node.
node: AdvancedCopy Manager logical node name
The system interrupts processing.
Verify that the mount point or disk resource or shared disk is correct.
The cluster deletion of the secondary node has been completed. Next, delete the cluster environment of the another secondary node.
The cluster deletion of the secondary node has been completed. Next, delete the cluster environment of the another secondary node.
The system ends processing.
In accordance with the procedure for deleting a cluster environment, perform the next step.
An internal inconsistency occurred.
An internal inconsistency occurred.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
val1 or val2 must be specified in option.
Value1 or value2 must be specified in option.
option: Option
val1: Specifiable value 1
val2: Specifiable value 2
The system interrupts processing.
Re-execute processing using correct values.
val must be specified in option.
Value must be specified in option.
option: Option
val: Specifiable value
The system interrupts processing.
Re-execute processing using correct values.
Failed to start the command. Error Code = code1-code2, Command Name = name
Failed to start the command.
code1: Error code 1
code2: Error code 2
name: Command name
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
The command was started by someone else than the root user.
The command was started by someone else than the root user.
The system interrupts processing.
The root user must invoke the command.
The -f option cannot be specified on the Storage server.
The -f option cannot be specified on the Storage server.
The system interrupts processing.
If the installed Storage server type is Manager, verify that the Storage management server service has not already been constructed.
Execute the command without the -f option.
The IP address was in an invalid format.
The IP address was in an invalid format.
The system interrupts processing.
Check the IP address.
A reserved word was specified as the node name.
A reserved word was specified as the node name.
The system interrupts processing.
Check the AdvancedCopy Manager logical node name.
Data different from the previous time was specified. Option = option, Data = data
Data different from the previous time was specified.
option: Option
data: Data previously specified
The system interrupts processing.
Check the option value.
Do not mount the shared disk.
Do not mount the shared disk.
The system interrupts processing.
Check the mount state of the shared disk for AdvancedCopy Manager share data.
When the Storage management server transactions, also check the mount state of DB file system.
Failed to start the mount check command.
Failed to start the mount check command.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
An error occurs though the cluster environment of AdvancedCopy Manager was removed. Carry out treatment corresponding to the message being output.
An error occurs though the cluster environment of AdvancedCopy Manager was removed. Carry out treatment corresponding to the message being output.
The system stops.
Respond to the message that system administrator immediately before this message.
The shared disk for another service is mounted. node=nodename.
The shared disk for another service is mounted.
The system interrupts processing.
Check whether the mounted shared disk is also object transactions.
The subnet was in an invalid format.
The subnet was in an invalid format.
The system interrupts processing.
Check the form of a subnetwork.
Failed in the acquisition of the device information.
Failed in the acquisition of the device information.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
A device is different. The last device=device1, This device=device2
The device has changed.
device1: The device mounted to the mount point of the shared disk for AdvancedCopy Manager share data when a command was executed last time.
device2: The device mounted to the mount point of the shared disk for current AdvancedCopy Manager share data.
The system interrupts processing.
Mount the last time used device and re-execute processing.
The service is not offline.
The service is not offline.
The system interrupts processing.
Stops the transactions and re-execute a command.
AdvancedCopy Manager has not been installed.
AdvancedCopy Manager has not been installed.
The system interrupts processing.
Verify that AdvancedCopy Manager has been correctly installed.
The IP address or subnet mask was incorrect.
The IP address or subnet mask was incorrect.
The system interrupts processing.
Check the IP address or subnet mask.
Failed to connect to the service control manager. Error Code = code
Failed to connect to the service control manager.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to open the service. Service Name: service, Error Code = code
Failed to open the service.
service: Service name
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to acquire the service status. Service Name: service, Error Code = code
Failed to acquire the service status.
service: Service name
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to wait for a thread. Error Code = error
Failed to wait for a thread.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to stop the service. Service Name: service, Error Code = code
Failed to stop the service.
service: Service name
code: Error code
The system interrupts processing.
Manually stop the service and re-execute processing.
Failed to stop the service (timeout). Service Name: service
Failed to stop the service due to a timeout.
service: Service name
The system interrupts processing.
Manually stop the service and re-execute processing.
The program will not be correctly installed if you cancel the setup now. Do you want to cancel the setup?
The program will not be correctly installed if you cancel the setup now. Do you want to cancel the setup?
The system interrupts processing if Yes is clicked.
Select "Yes" to cancel setup.
Select "No" to continue setup.
No parameter was entered.
No parameter was entered.
The system interrupts processing.
Enter parameters that were not entered.
The free space was not sufficient for the setup.
The free space was not sufficient for the setup.
The system interrupts processing.
Secure necessary free space.
Verify that you have the ownership for the selected disk.
Check the status of the selected disk.
An invalid subnet mask was used.
An invalid subnet mask was used.
The system interrupts processing.
Check the IP address or subnet mask.
Failed to create a directory. Directory = path
Failed to create a directory.
path: Directory path
The system interrupts processing.
After creating a directory, re-execute processing.
Failed to set up registry information.
Failed to set up registry information.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
[Windows version]
Chapter 10.2.2, "Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
The cluster environment will not be released if you cancel the unsetup now. Do you want to cancel the unsetup?
The cluster environment will not be released if you cancel the unsetup now. Do you want to cancel the unsetup?
The system interrupts processing if Yes is clicked.
Select "Yes" to cancel unsetup.
Select "No" to continue unsetup.
No logical node name was selected.
No logical node name was selected.
The system interrupts processing.
Select a logical node name.
Failed to create a thread. Error Code = code
Failed to create a thread.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Are you sure the cluster environment may be forcibly released?
Are you sure the cluster environment may be forcibly released?
The cluster environment is forcibly released if Yes is clicked.
Select "Yes" to continue forcibly unsetup.
Select "No" to cancel forcibly unsetup.
Usage: stgclset_safe -k NodeType -m MountPoint -n NodeName -s Service] [[-i IPAddress -f mgr]
An invalid option was specified.
The system interrupts processing.
After checking the command, re-execute processing.
For the primary node, specify an IP address, node name, and service name.
For the primary node, specify an IP address, node name, and service name (job name).
The system interrupts processing.
After checking the command, re-execute processing.
For the secondary node, no node type, or mount point can be specified.
For the secondary node, no node type, or mount point can be specified.
The system interrupts processing.
After checking the command, re-execute processing.
Failed to register the status transition procedure. Error Code = code1-code2
Failed to register the status transition procedure.
code1: Error code1
code2: Error code2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
SynfinityCluster or PRIMECLUSTER has not been installed.
SynfinityCluster or PRIMECLUSTER has not been installed.
The system interrupts processing.
Check the SynfinityCluster or PRIMECLUSTER environment.
Usage: stgclunset_safe -n NodeName [-f]
An invalid option was specified.
The system interrupts processing.
After checking the command, re-execute processing.
Failed to delete the status transition procedure. Error Code = code1-code2
Failed to delete the status transition procedure.
code1: Error code1
code2: Error code2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
For the Storage management server transaction, specify an IP Address.
For the Storage management server transaction, specify an IP Address.
The system interrupts processing.
Re-execute after checking a command.
For the Storage server transaction, no IP Address can be specified.
For the Storage server transaction, no IP Address can be specified.
The system interrupts processing.
Re-execute after checking a command.
A parameter was specified.
A parameter was specified.
The system interrupts processing.
Execute the command without specifying a parameter.
Cluster Service was not started.
Cluster Service was not started.
The system interrupts processing.
Check the MSCS or cluster service environment.
MSCS has not been installed.
MSCS has not been installed.
The system interrupts processing.
Check the MSCS or cluster service environment.
Failed to acquire the drive name from the physical disk resource.
Failed to acquire the drive name from the physical disk resource.
The system interrupts processing.
Check the MSCS or cluster service environment.
The usage of the IP address was not specified.
The usage of the IP address was not specified.
The system interrupts processing.
Specify the usage of the IP address.
Failed to acquire the quorum disk name. Error Code = code
Failed to acquire the quorum disk name.
Code: Error code
The system interrupts processing.
Verify that the quorum disk is operating normally.
Failed to acquire the quorum disk information.
Failed to acquire the quorum disk information.
The system interrupts processing.
Acquire the ownership of the quorum disk.
Failed to acquire the quorum disk information. Error Code = code
Failed to acquire the quorum disk information.
Code: Error code
The system interrupts processing.
Verify that the quorum disk is operating normally.
Failed to acquire the primary node name. Error Code = code
Failed to acquire the primary node name.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to check the cluster group. Error Code = code
Failed to check the cluster group.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to create a cluster group. Error Code = code
Failed to create a cluster group.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to set up the property information of the cluster group. Error Code = code
Failed to set up the property information of the cluster group.
code: Error code
The system interrupts processing.
Verify that the cluster name is correct.
Check whether group group1 exists. Error Code = code
Check whether group exists.
group1: Cluster group name
code: Error code
The system interrupts processing.
Verify that the group exists.
Failed to create a cluster resource. Error Code = code
Failed to create a cluster resource.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to set up the property information of the cluster resource. Error Code = code
Failed to set up the property information of the cluster resource.
code: Error code
The system interrupts processing.
Check whether the network name for external connection is right.
Check whether the network name overlaps others.
Check whether the IP address overlaps others.
Failed to add a cluster dependence relationship. Error Code = code
Failed to add a cluster dependence relationship.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to copy registry registry1. Resource Name = resource
Failed to replicate the registry.
registry1: Registry
resource: Resource name
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to set up the priority ownership. Error Code = code
Failed to set up the priority ownership.
code: Error code
The system interrupts processing.
It checks whether the cluster group specified by the service name (job name) in the cluster administrator is created. When there is a cluster group, the property of a cluster group is opened and it checks whether priority ownership is set up.
There is a cluster group, and when priority ownership is set up, a cluster setting command is executed again.
When there is no cluster group, the cluster group of a service name (job name) is created and a cluster setting command is executed again.
When priority ownership is not set up, priority ownership is set up and a cluster setting command is executed again.
Failed to acquire the local node name. Error Code = code
Failed to acquire the local node name.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Acquire the ownership of group group1.
Acquire the ownership of the group.
group1: Cluster group name
The system interrupts processing.
Acquire the ownership of the cluster group.
Failed to check the ownership of the group. Error Code = code
Failed to check the ownership of the group.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to place resource offline. Error Code = code1-code2
Failed to place the resource offline.
resource: Resource name
code1: Error code 1
code2: Error code 2
The system interrupts processing.
After manually placing the resource offline, re-execute processing.
Failed to delete the resource. Resource Name = resource, Error Code = code
Failed to delete the resource.
resource: Resource name
code: Error code
The system continues processing.
Manually delete the resource.
Failed to move the group. Error Code = code
Failed to move the group.
code: Error code
The system continues processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to find the cluster file. File Name = filename
Failed to find the cluster file.
filename = Cluster file name
The system interrupts processing.
Verify that the shared disk is online.
Usage : stgclset_mcsg -k NodeType -m MountPoint [-n NodeName -s Service -v VolumeGroup -i IPAddress -u Subnet]
Invalid option is specified.
The system interrupts processing.
Re-execute after checking a command.
For the primary node, specify all options.
For the primary node, specify all options.
The system interrupts processing.
Re-execute after checking a command.
For the secondary node, no node name or mount point can be specified.
For the secondary node, no node name or mount point can be specified.
The system interrupts processing.
Re-execute after checking a command.
Usage : stgclunset_mcsg -n NodeName [-f]
Invalid option is specified.
The system interrupts processing.
Re-execute after checking a command.
Failed in the preparation of the AdvancedCopy Manager start/stop command for the package.
Failed in the preparation of the AdvancedCopy Manager start/stop command for the package.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed in the deletion of the AdvancedCopy Manager start/stop command for the package.
Failed in the deletion of the AdvancedCopy Manager start/stop command for the package.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed in the preparation of the sample control script for the package.
Failed in the preparation of the sample control script for the package.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Usage : stgclset_vcs -k NodeType -m MountPoint [ -n NodeName -s Service] [-i IPAddress -f mgr]
An invalid option was specified.
The system interrupts processing.
After checking the command, reexecute processing.
For the primary node, specify a node name, service name.
For the primary node, specify a node name, service name.
The system interrupts processing.
After checking the command, reexecute processing.
VERITAS Cluster Server has not been installed.
VERITAS Cluster Server has not been installed.
The system interrupts processing.
Check the environment of VERITAS Cluster Server.
Usage: stgclunset_vcs -n NodeName [-f]
An invalid option was specified.
The system interrupts processing.
After checking the command, reexecute processing.
Failed to create the AdvancedCopy Manager application. Error Code = code1-code2
Failed to make the AdvancedCopy Manager application.
code1: Error code 1
code2: Error code 2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
For the secondary node, it can not be specified except for node type and mount point.
For the secondary node, it can not be specified except for node type and mount point.
The system interrupts processing.
Re-execute after checking a command.
For the Storage management server transaction, specify an IP address.
For the Storage management server transaction, specify an IP address.
The system interrupts processing.
Re-execute after checking a command.
For the Storage server transaction, no IP address can be specified.
For the Storage server transaction, no IP address can be specified.
The system interrupts processing.
Re-execute after checking a command.
Failed to delete the AdvancedCopy Manager application. Error Code = code1-code2
Failed to delete the AdvancedCopy Manager application.
code1: Error code 1
code2: Error code 2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Usage: stgclset_lxprm -k NodeType -m MountPoint [-n NodeName -s Service] [-i IPAddress -f mgr]
An invalid option was specified.
The system interrupts processing.
After checking the command, re-execute processing.
For the primary node, specify a node name and service name.
For the primary node, specify a node name and service name.
The system interrupts processing.
After checking the command, re-execute processing.
For the secondary node, it can not be specified except for node type and mount point.
For the secondary node, it can not be specified except for node type and mount point.
The system interrupts processing.
After checking the command, re-execute processing.
Failed to register the status transition procedure. Error Code = code1-code2
Failed to register the status transition procedure.
code1: Error code1
code2: Error code2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
PRIMECLUSTER has not been installed.
PRIMECLUSTER has not been installed.
The system interrupts processing.
Check the PRIMECLUSTER environment.
Usage: stgclunset_lxprm -n NodeName [-f]
An invalid option was specified.
The system interrupts processing.
After checking the command, re-execute processing.
Failed to delete the status transition procedure. Error Code = code1-code2
Failed to delete the status transition procedure.
code1: Error code1
code2: Error code2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
For the Storage management server transaction, specify an IP address.
For the Storage management server transaction, specify an IP Address.
The system interrupts processing.
Re-execute after checking a command.
For the Storage server transaction, no IP address can be specified.
For the Storage server transaction, no IP Address can be specified.
The system interrupts processing.
Re-execute after checking a command.
An internal inconsistency occurred.
An internal inconsistency occurred.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
No port number was entered.
No port number was entered.
The system interrupts processing.
Enter the port number.
The same port number was entered.
The same port number was entered.
The system interrupts processing.
Check the port number.
Check whether a port number is right. Please perform by the port number which is not used by others.
Port number specified in service1 has already been specified.
Service that uses the port number=service2
The port number which had already been registered was specified.
service1: Service name
service2: The registered service name
The system interrupts processing.
Check the port number.
An error occurred in searching port number information.
An error occurred in searching port number information.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Port number specified in service1 has been set up with a different number.
Port number specified has been set up with a different number.
Service1: Service name
The system interrupts processing.
Check the port number.
When you change a port number, please change manually the port number of the business-use communication service (stgxfws_logic node name) indicated by Windows installation directory \system32\drivers\etc\services, and re-perform it.
Failed to register service service1.
Failed to register service.
Service1: Service name
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to delete service service1.
Failed to delete service.
Service1: Service name
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to acquire an account of AdvancedCopy Manager.
Failed to acquire an account of AdvancedCopy Manager.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to register to the port number management file. Error=code
Failed to register to the port number management file.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to read the port number management file. Error=code
Failed to read the port number management file.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to write the port number. Error=code
Failed to write the port number.
code: Error code
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Failed to acquire machine information.
Failed to acquire machine information.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
An invalid password was entered.
An invalid password was entered.
The system interrupts processing.
Check the password.
Failed to write the linefeed.
Failed to write the linefeed.
The system interrupts processing.
Start a new line for the last of a Windows installation directory \system32\drivers\etc\services file manually, and perform again.
Failed to confirm the linefeed.
Failed to confirm the linefeed.
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
This command arguments are incorrect.
The command arguments are incorrect.
The system interrupts processing.
Do not execute this command. Execute the cluster unsetup command to unsetup the cluster setting.
Failed to open the cluster environment setting file. Filename=[FILE NAME]
The cluster environment setting file(clsetup.ini) could not be opened.
FILE NAME: File name
The system interrupts processing.
Check for the presence of the file and the access permission and execute the command again.
Failed to read the cluster environment setting file. Filename=[FILE NAME], Section=[SECTION], Key=[KEY]
The cluster environment setting file(clsetup.ini) could not be read.
FILE NAME: File name
SECTION: Section name
KEY: Key name
The system interrupts processing.
Check the access permission and the correctness of the file data and execute the command again.
Failed to open the registry. Registry=[REGISTRY], Key=[KEY], Error=[ERROR]
The registry could not be opened.
REGISTRY: Registry
KEY: Key name
ERROR: Error code
The system interrupts processing.
Recover registry information by using the OS standard function.
Failed to read the registry. Registry=[REGISTRY], Key=[KEY], Value=[ERROR], Error=[ERROR]
The registry could not be read.
REGISTRY: Registry
KEY: Key name
VALUE: Value name
ERROR: Error code
The system interrupts processing.
Recover registry information by using the OS standard function.
Failed to open the cluster setting definition file. Filename=[FILE NAME]
The cluster setting define file could not be opened.
FILE NAME: File name
The system interrupts processing.
Check for the presence of the cluster setting definition file [FILE NAME] and the access permission and execute the command again.
Failed to read the cluster setting definition file. Filename=[FILE NAME], Line=[LINE], Value=[VALUE]
The cluster setting definition file could not be read.
FILE NAME: File name
LINE: Line number
VALUE: Data
The system interrupts processing.
The cluster setting definition file [FILE NAME] may be corrupt. Replace the cluster setting definition file with the file installed and execute the command again.
The directory does not exist. Directory=[DIRECTORY]
The directory could not be found.
DIRECTORY: Directory
The system interrupts processing.
Check for the presence of the directory and the access permission and execute the command again.
Failed to copy the directory. Source Directory=[DIRECTORY], Target Directory=[TARGET DIRECTRY]
The directory could not be copied.
SOURCE DIRECTORY: Source directory for copying
TARGET DIRECTORY: Target directory for copying
The system interrupts processing.
Check for the presence of the directory, the access permission, and the free disk space and execute the command again.
Failed to delete the directory. Directory=[DIRECTORY]
The directory could not be deleted.
DIRECTORY: Directory
The system interrupts processing.
Check for the presence of the directory and the access permission and execute the command again.
Failed to move the directory. Source Directory=[SOURCE DIRECTORY], Target Directory=[TARGET DIRECTORY]
The file could not be moved.
SOURCE DIRECTORY: Source directory for moving
TARGET DIRECTORY: Target directory for moving
The system interrupts processing.
Check for the presence of the directory, the access permission, and the free disk space and execute the command again.
Failed to create a directory. Directory=[DIRECTORY]
The directory could not be created.
DIRECTORY: Directory name
The system interrupts processing.
Check the access permission and the free disk space and execute the command again.
Failed to copy the file. Source Filename=[SOURCE FILE], Target Filename=[TARGET FILE]
The file could not be copied.
SOURCE FILE: Source file for copying
TARGET FILE: Target file for copying
The system interrupts processing.
Check for the presence of the file and the access permission and execute the command again.
Failed to delete the file. Filename=[FILE NAME]
The file could not be deleted.
FILE NAME: File name
The system interrupts processing.
Check for the presence of the file and the access permission and execute the command again.
Failed to move the file. Source Filename=[SOURCE FILE], Target Filename=[TARGET FILE]
The file could not be moved.
SOURCE FILE: Source file for moving
TARGET FILE: Target file for moving
The system interrupts processing.
Check for the presence of the directory, the access permission, and the free disk space and execute the command again.
Failed to create a link. Source Path=[SOURCE PATH], Target Path=[TARGET PATH]
The link could not be created.
SOURCE PATH: Link source
TARGET PATH: Link target
The system interrupts processing.
Check for the presence of the directory, the access permission, and the free disk space and execute the command again.
The command could not be called or the command failed. Command Line=[COMMANDLINE]
The command could not be executed or command failed.
COMMANDLINE: Command line
The system interrupts processing.
Check for the presence of the [COMMANDLINE] command.
If [COMMANDLINE] is the smcvtenv command, collect the following file, then contact a Fujitsu systems engineer.
[Solaris version]
[HP version]
[Linux version]
/var/opt/FJSVswssc/log/swclsetup.log
[Windows version]
Work-directory\var\security\log\swclsetup.log
Usage : swtgclset_hacmp -k NodeType -m MountPoint [-n NodeName -s Service]
An invalid option was specified.
The system interrupts processing.
After checking the command, reexecute processing.
For the primary node, specify a node name, service name.
For the primary node, specify a node name, service name.
The system interrupts processing.
After checking the command, reexecute processing.
High Availability Cluster Multi-Processing has not been installed.
High Availability Cluster Multi-Processing has not been installed.
The system interrupts processing.
Check the environment of High Availability Cluster Multi-Processing.
Usage : stgclunset_hacmp -n NodeName [-f]
An invalid option was specified.
The system interrupts processing.
After checking the command, reexecute processing.
Failed to create the AdvancedCopy Manager application. Error Code = code1-code2
Failed to make the AdvancedCopy Manager application.
code1: Error code 1
code2: Error code 2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
For the secondary node, it can not be specified except for node type and mount point.
For the secondary node, it can not be specified except for node type and mount point.
The system interrupts processing.
Re-execute after checking a command.
Failed to delete the AdvancedCopy Manager application. Error Code = code1-code2
Failed to delete the AdvancedCopy Manager application. Error Code = code1-code2
code1: Error code 1
code2: Error code 2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Usage : stgclset_aixvcs -k NodeType -m MountPoint [ -n NodeName -s Service]
An invalid option was specified.
The system interrupts processing.
After checking the command, reexecute processing.
For the primary node, specify a node name, service name.
For the primary node, specify a node name, service name.
The system interrupts processing.
After checking the command, reexecute processing.
VERITAS Cluster Server has not been installed.
VERITAS Cluster Server has not been installed.
The system interrupts processing.
Check the environment of VERITAS Cluster Server.
Usage: stgclunset_aixvcs -n NodeName [-f]
An invalid option was specified.
The system interrupts processing.
After checking the command, reexecute processing.
Failed to create the AdvancedCopy Manager application. Error Code = code1-code2
Failed to make the AdvancedCopy Manager application.
code1: Error code 1
code2: Error code 2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
For the secondary node, it can not be specified except for node type and mount point.
For the secondary node, it can not be specified except for node type and mount point.
The system interrupts processing.
Re-execute after checking a command.
Failed to delete the AdvancedCopy Manager application. Error Code = code1-code2
Failed to delete the AdvancedCopy Manager application. Error Code = code1-code2
code1: Error code 1
code2: Error code 2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
Usage : stgclset_hpvcs -k NodeType -m MountPoint [ -n NodeName -s Service]
An invalid option was specified.
The system interrupts processing.
After checking the command, reexecute processing.
For the primary node, specify a node name, service name.
For the primary node, specify a node name, service name.
The system interrupts processing.
After checking the command, reexecute processing.
VERITAS Cluster Server has not been installed.
VERITAS Cluster Server has not been installed.
The system interrupts processing.
Check the environment of VERITAS Cluster Server.
Usage: stgclunset_hpvcs -n NodeName [-f]
An invalid option was specified.
The system interrupts processing.
After checking the command, reexecute processing.
Failed to create the AdvancedCopy Manager application. Error Code = code1-code2
Failed to make the AdvancedCopy Manager application.
code1: Error code 1
code2: Error code 2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
For the secondary node, it can not be specified except for node type and mount point.
For the secondary node, it can not be specified except for node type and mount point.
The system interrupts processing.
Re-execute after checking a command.
Failed to delete the AdvancedCopy Manager application. Error Code = code1-code2
Failed to delete the AdvancedCopy Manager application. Error Code = code1-code2
code1: Error code 1
code2: Error code 2
The system interrupts processing.
Refer to the following manual and collect the data necessary to solve the error, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the ETERNUS SF AdvancedCopy Manager Operator's Guide
|
Contents
Index
|