Dynamic Reconfiguration User's Guide I/O device edition - for Solaris (TM) Operating System -

5.1.8 Network driver configuration changing

• In case of configuring parameters in driver.conf(4) file and replacing or expanding the system board by using DR, the PCI card on the replaced or expanded system board, their parameters which configured in driver.conf(4) file may not be valid.

  To change the initial parameters of the PCI card on the replaced or expanded system board by using DR, please refer to the solution of each PCI card shown below. (Each PCI card manual(*1) has the description of setting by the ndd command. Please refer it.)

  Product ID (Functions)	Software of driver (driver name)	Resolution
  X1033A-U X1033A-X and Onboard LAN interface (*2) (10/100BASE-T)	Solaris (hme)	Please make a setting by the ndd command. Or please reboot a system after changing the /kernel/drv/hme.conf file.
  PW008FE1 (10/100BASE-T)	FUJITSU PCI 10/100 Ethernet 1.0 or later (supplied with a PCI card)	Please make a setting by the ndd command. Or please reboot a system after changing the /kernel/drv/fjfe.conf file.
  PW008QE1 (10/100BASE-T x4)	FUJITSU PCI Quad 10/100 Ethernet 1.0 or later (supplied with a PCI card)	Please make a setting by the ndd command. Or please reboot a system after changing the /kernel/drv/fjqe.conf file,
  PW008QE2 (10/100BASE-T x4)	FUJITSU PCI Quad 10/100 Ethernet 1.1 or later (supplied with a PCI card)	Please make a setting by the ndd command. Or please reboot a system after changing the /kernel/drv/fjqe.conf file.
  PP028GE1U PP028GE1X (1000BASE-SX)	FUJITSU PCI Gigabit Ethernet 1.4.1 or later (supplied with a PCI card)	The ndd command is not supported. Please reboot a system after changing the /kernel/drv/fjge.conf file.
  PW008GE1U PW008GE1X (1000BASE-T)	FUJITSU PCI Gigabit Ethernet 1.4.1 or later (supplied with a PCI card)	The ndd command is not supported. Please reboot a system after changing the /kernel/drv/fjge.conf file.
  PW008GE4 (1000BASE-SX)	FUJITSU PCI Gigabit Ethernet 2.0 or later (supplied with a PCI card)	Please make a setting by the ndd command. Or please reboot a system after changing the /platform/sun4us/kernel/drv/fjgi.conf file.
  PW008GE5 (10/100/1000BASE-T)	FUJITSU PCI Gigabit Ethernet 2.0 or later (supplied with a PCI card)	Please make a setting by the ndd command. Or please reboot a system after changing the /platform/sun4us/kernel/drv/fjgi.conf file.
  PW008QG1 (10/100/1000BASE-T x4)	FUJITSU PCI Gigabit Ethernet 2.3 or later (supplied with a PCI card)	Please make a setting by the ndd command. Or please reboot a system after changing the /platform/sun4us/kernel/drv/fjgi.conf file.

  (*1) In case of X1033A-U(-X), please refer to Sun Microsystems, Inc web page about "Platform Notes: The hme FastEthernet Device Driver" and ndd(1M) man page etc..

  (*2) The below machines have an Onboard LAN interface (hme).
  - PRIMEPOWER 800/1000/2000, 900/1500/2500

• In case of using the JumboFrame feature of "FUJITSU PCI Gigabit Ethernet 1.4.1" or "FUJITSU PCI Gigabit Ethernet 2.0" or later, TCP/IP MTU size configured in "/etc/fjmtu.fjgeX" file or "/etc/fjmtu.fjgiX" file is not set to the interface of the PCI card on the replaced or expanded system board after replacing or expanding the system board by using DR feature.
  
  Please configure the TCP/IP MTU size of that interface using by either following procedure.
  • Configure the TCP/IP MTU size by ifconfig(1M) command.
    Following example configures the MTU size of fjgi0 to 1500.

    # ifconfig fjgi0 mtu 1500 <RETURN>

    
    
  • Reboot the system after configuration of the "/etc/fjmtu.fjgeX" file or "/etc/fjmtu.fjgiX" file.
  
  
• In case of configuring MAC local address on Netcompo FNA-LAN, replacement and extension of PCI card are not supported.
  Please reboot the system after configuration of the "/etc/opt/FSUNnet/mactool/macaddr.conf" file. Please refer to the "Netcompo FNA-LAN User's Guide" for details of the configuration of MAC local address.