Machine Administration Guide 2.6

4.38 setrci (1M)

Name

setrci - RCI-related setting command

Format

/usr/sbin/FJSVmadm/setrci subcommand

Function

Makes the hardware settings for a device that requires RCI-related settings.
This command also displays a list of RCI devices that this main unit recognizes.

Subcommands

The subcommands are:

• stat
• init
• set host_no
• mainte
• initconfig
• config

The init and set subcommands are not supported by PRIMEPOWER250/450/650/850.

stat

Function

Displays the RCI status of the main unit and the addresses and the statuses of the devices connected to the RCI.

Displayed item

The following information is displayed as the RCI information for the main unit.

RCI address

The RCI address of the main unit.

Status

The RCI status. The messages corresponding to the individual status are:

Active : RCI is active.
Mainte : RCI is in maintenance mode.
Configuring : The RCI network is being constructed.
ConfigError(reason) : RCI network construction error.

In (reason), one of the following reasons is displayed.

Reason	Reason for the status
"Self Host Address Conflict"	Local address duplication error
"Host Address Contradict"	Host number or host address inconsistency
"RCI Address Contradict"	RCI address inconsistency
"Can't assign new Address"	New registration unacceptable
"Error in Configuring"	Error in incorporation
"Self configuration RCI Address Conflict"	Locally constructed RCI address duplication error
"RCI Hardware Error"	RCI hardware error

The following information is displayed for each RCI-connected unit.

Address: RCI Address

Use this information to specify a device for hot swapping of fans or power supply units.

Pwr: Power supply status

Status	Definition
ON	Power-on status
OFF	Power-off state

Alm: Alarm out status

Status	Definition
ALM	Alarm out status
-	No alarm

I/F: Interface status

Status	Definition
ACT	Active status
INACT	Inactive status

sys-phase: OS status

Status	Definition
power-off	Power-off state
panic	Panic status
shdwn-start	Shutting down
shdwn-cmplt	Shutdown completed
dump-cmplt	Dump completed
OBP/POST	Initial diagnosis in progress
booting	Booting
running	Running

Ctgry: Category

Category	Definition
host	Main unit
rcic	External power supply unit
disk	Disk unit
lnsw	Line switch
other	Other device

dev-cls: device class

Four digits in hexadecimal format.

sub-cls: subclass

Two digits in hexadecimal format.

tm-out: Monitoring time of no-communication-timeouts

The monitoring time of no-communication-timeouts of monitoring of the RCI unit is displayed.

For devices not supported, "-" is displayed.

Display example

The following is a display example:

# /usr/sbin/FJSVmadm/setrci stat

HOST

 address 000101ff

 Active

LIST

 address  pwr alm I/F   sys-phase   ctgry dev-cls sub-cls tm-out

 000101ff ON  -   ACT   running     host  0001    04      -

 000102ff ON  -   ACT   running     host  0001    04      -

 000103ff ON  -   ACT   running     host  0001    04      -

 000104ff ON  -   ACT   running     host  0001    04      -

 000105ff ON  -   ACT   running     host  0001    04      -

 000106ff ON  -   ACT   running     host  0001    04      -

 003001ff ON  -   ACT   -           rcic  0200    02      40

 003002ff ON  -   ACT   -           rcic  0200    02      40

 003003ff OFF ALM ACT   -           disk  0400    02      40

 003004ff ON  -   ACT   -           disk  0400    05      180

 002009ff ON  -   ACT   -           lnsw  0800    01      40

init

Function

Sets the RCI address to the default value.

set host_no

Function

Sets the RCI address of the host.

Option

The options are:

host_no

Specify the RCI host address in the following form:
0x0001**ff
Specify host_no in the part indicated by **.
The range of settings is 01 to 20.

mainte

Function

Displays the settings of the RCI maintenance mode.
In maintenance mode, the system performs general monitoring processing but it does not report errors. This mode is used for maintenance of RCI-connected units.
You can set the maintenance mode using the mode switch located on the front panel of the main unit.
This command displays the mode of the current RCI network.

Display example

The following is a display example:

# /usr/sbin/FJSVmadm/setrci mainte

RCI Maintenance Mode: enable

initconfig

Function

Instructs initial incorporation of an RCI device.
For reconfiguration of an RCI, issue the instruction for its incorporation.

config

Function

Instructs incorporation of an RCI device.
For reconfiguration of an RCI after addition or reduction of RCI devices, issue the instruction for its incorporation.

End status

The end status can be:
0: Normal end
Other than 0: Error