Top
Systemwalker Operation Manager  Cluster Setup Guide for UNIX
FUJITSU Software
Chapter 7 Cluster Setup Procedure Specific to Systems Using MC/ServiceGuard > 7.1 Registering Systemwalker Operation Manager with the MC/ServiceGuard System > 7.1.2 Registering package
PreviousNext

7.1.2 Registering package

Use MC/ServiceGuard cluster system commands to register the package and to check that it has been registered correctly.

Refer to the MC/ServiceGuard manual for details on these commands.

Procedure

This section explains the procedure for registering the package and checking that it has been registered correctly.

1) Store the script files

Package configuration scripts can be stored on either the active node or the standby node, but package control scripts and package monitoring scripts must be stored on all nodes (active and standby).

Store the package control script in the location specified in the package configuration file, and save the package monitoring script in the location specified in the package control script, as shown in the following example.

For 1:1 active/standby configurations

For N:1 active/standby configurations (if there are three active nodes)

For dual node mutual standby configurations

2) Verify the package configuration file

Execute the MC/ServiceGuard cmcheckconf command on the node where the package configuration file has been saved to check whether the package configuration file is correct.

# cmcheckconf -P /etc/cmcluster/omgr/omgr.conf

3) Register the package configuration file

Execute the MC/ServiceGuard cmapplyconf command on the node where the package configuration file has been saved to register the package configuration file.

# cmapplyconf -v -P /etc/cmcluster/omgr/omgr.conf

Enter "y" when the "Modify the package configuration ([y]/n)?" message is output.
This completes the package registration.

4) Check the registered information

Use the following command to check whether the information in the package configuration file has been registered correctly.

# cmviewconf

Check the display after "Package information:" to see whether the package name, package control script, package monitoring script, active node, and standby node have been registered correctly.

The following display example is for a 1:1 active/standby configuration.

Package information:
  package ID 56321:
    package name:               omgr

(omitted)

    package run script:         /etc/cmcluster/omgr/omgr.sh
    package run timeout:        (No Timeout)
    package halt script:        /etc/cmcluster/omgr/omgr.sh
    package halt timeout:       (No Timeout)
    package primary node:       hp01
    package alternate node:     hp02

Check the operation status of each node using the following command:

# cmviewcl

Make sure that the "STATUS" and "STATE" of each "NODE" are "up" and "running".

The following display example is for a 1:1 active/standby configuration.

CLUSTER      STATUS       
cluster1     up           

  NODE         STATUS       STATE        
  hp01         up           running      
  hp02         up           running      

    PACKAGE      STATUS       STATE        PKG_SWITCH   NODE  
    omgr         down         halted       disabled     unowned

Check the switch status of each node using the following command:

# cmviewcl -v -p omgr

Check the "Node_Switching_Parameters: " section and make sure that "SWITCHING" is enabled for each "NODE_TYPE ".

The following display example is for a 1:1 active/standby configuration.

    PACKAGE      STATUS       STATE        PKG_SWITCH   NODE  
    omgr         down         halted       disabled     unowned

(omitted)

      Node_Switching_Parameters:
      NODE_TYPE    STATUS       SWITCHING    NAME    
      Primary      up           enabled      hp01    
      Alternate    up           enabled      hp02

Verify the entire cluster system by repeating steps 2) through 4) "N" times for N:1 active/standby configurations and twice for dual node mutual standby configurations on the nodes where the package configuration files have been saved.

PreviousNext
Copyright 1995-2022 FUJITSU LIMITED