Note
REC [4.3A20 or earlier]
The cooperation with REC is not supported in 4.3A20 or earlier version. When creating snapshots on two or more ETERNUS Disk storage systems, configure the disk array unit as REC is disabled in advance.
Note
Multipath Software [4.3A20 or earlier]
When using DM-MP, the cooperation with the Advanced Copy function is not supported. When using the Advanced Copy function with snapshot operations, use ETERNUS Multipath Driver instead of DM-MP.
In a proxy configuration, by working in cooperation with the Advanced Copy functions, EC (including REC for 4.3A30 or later), or OPC (including QuickOPC for 4.3A30 or later) of ETERNUS Disk storage system, the copying between master and proxy can be performed without imposing loads on primary servers or a SAN. In this situation, disk array units carry out copying processes and the processes will continue running even if the server is rebooted.
When the Advanced Copy function is available, it is used for copying between the master and the proxy. However, in the following situations, a soft copy function (a copy function of a GDS driver operating on a server) is used.
The Advanced Copy function is not used when:
Use of soft copy functions was specified explicitly using the sdxproxy command with the -e softcopy option
The master and the proxy belong to a root class. [EFI]
The copy destination volumes are in a mirroring configuration.
Note, however, that even if the master as the copy destination is in a mirroring configuration, OPC is available for copying from the proxy when:
Executing [Operation]:[Proxy Operation]:[Restore] in GDS Management View and selecting "No" to "Rejoin" in the [Restore Master] dialog box. For details see "7.10.1.2 Operation Procedure."
Executing the sdxproxy Restore command. For details see "B.2.1 sdxproxy - Proxy Object Operations."
A lower level group is connected to a group to which master volumes or proxy volumes belong.
The number of concurrent EC or OPC sessions has reached the upper limit defined by the disk array unit.
See
The number of allowed concurrent sessions is either the upper limit within one physical disk (LU) or the upper limit within one disk array unit. For details, see the handbook of the relevant disk array.
Multiple proxy volumes are related to a master volume and the number of proxy volumes with EC sessions has reached the upper limit (16 volumes).
Disks that constitute the master or the proxy were registered with a class before installing the Advanced Copy function on the disk array unit.
In these situations, operations based on OPC functions are impossible. For such operations see "3.18 Instant Snapshot by OPC."
EC is used for synchronization copying from a master to a proxy after joining or rejoining them, copying for maintaining synchronization, and recording the portion updated while a master and a proxy are parted.
OPC is used for synchronization copying, instant snapshot processing, and restoring a master using the proxy data.
If any EC sessions exist between a master and a proxy, OPC cannot be initiated between the master and another proxy.
When both EC and OPC are available as with ETERNUS Disk storage system, EC has precedence over OPC. Once an EC session is stopped, you cannot use the EC function afterwards. EC sessions are stopped in the following situations.
EC sessions are stopped when:
Executing [Operation]:[Proxy Operation]:[Part] in GDS Management View and selecting "Yes" to "Instant Snapshot" in the [Part Proxy] dialog box
Canceling the EC sessions with the sdxproxy Cancel command
Joining a master and a proxy and using a soft copy function with the sdxproxy Join -e softcopy command
Creating instant snapshots with the sdxproxy Part -e instant command
Rejoining a master and a proxy and using a soft copy function with the sdxproxy Rejoin -e softcopy command
To make the EC function available after conducting these operations, break the relationship between the master and the proxy once and rejoin them.
To check the modes of the copying in execution, use either:
The [Copy Type] field of the slice information field in GDS Management View
The CPTYPE field displayed with the sdxinfo command
Additionally, the types and the statuses of sessions between the master and the proxy can be viewed in the FUNC field and the CPSTAT field displayed with the sdxinfo command.
Note
Advanced Copy Control
When the Advanced Copy function is available, executing the sdxproxy command directs GDS to control the Advanced Copy on the master and the proxy. Do not use any other methods other than the sdxproxy command to apply such control on a master and a proxy.
