SYNOPSIS
sdxfix -C -c class
sdxfix -D -c class -d disk [-e online] [-x Devlabel,NoRdchk]
sdxfix -V -c class {-g group|-d disk} -v volume [-e force] [-x NoRdchk]
DESCRIPTION
Use sdxfix to restore failed objects (excluding shadow objects). Data on restored disks or volume objects may no longer have consistency, and after the restoration, it is necessary to restore consistency using backup data or checking with the "fsck" command. The "sdxfix" command can be executed with superuser access privileges only.
PRIMARY OPTIONS
You can use one of the following options.
Class
Restores closed class to a normal status on the current node.
This command can restore class when the class includes a configuration database normally accessible and:
less than 3 disks in ENABLE status and 1 or more disks normally accessible
three to 5 disks in ENABLE status and 2 or more disks normally accessible
six or more disks in ENABLE status and 3 or more disks normally accessible
After restoration is complete, objects within the class are restored to the previous status. However, if class is a local class, volumes that were in STOP status before the class closure will be in ACTIVE status. Additionally, if class is a shared class, volumes that were in ACTIVE status before the class closure will be in STOP status.
Disk
Restores the state of disk disk that detected an I/O error.
Reads all disk area, and if there's no problem, then clears the error status. Response from the command requires some time depending on the disk size because the entire disk area is read.
For restoring the object status without reading the disk area, specify the sub option -x NoRdchk.
If there's a volume in the highest-level group to which disk belongs, or disk has a single volume, the volume should be stopped or inactive (STOP or INVALID) on all nodes (except when -e online is specified).
When disk is connected to a switch group, restoration fails. To clear an I/O error in a disk connected to a switch group, use the sdxswap -O command to make the disk exchangeable and then use the sdxswap -I command to make the disk useable.
Volume
Restores a slice with invalid data (INVALID) or a not-ready slice (NOUSE) specified by a set of disk and volume or by a set of group and volume to the STOP status to restore the volume with invalid data (INVALID) to the STOP status.
The volume should be stopped or inactive (STOP or INVALID) on all nodes. The slice state specified in the combination of disk and volume, or group and volume should be INVALID or NOUSE.
Reads the entire slice specified in the combination of disk and volume, or group and volume, and if there's no problem, changes the state to STOP, and then changes the state of a stopped slice to INVALID.
SUB OPTIONS
You can use the following sub-options.
Specify a name of the class to which the object belongs.
Specify a name of the disk.
When volume is a mirror volume, specify a name of the disk that is connected to the mirror group to which the volume belongs. This disk should have the INVALID mirror slice that needs to be restored to STOP.
Specify a single disk name when volume is a single volume.
When volume is a switch volume, specify a disk name of the active disk connected to a switch group that includes the volume into disk. Do not set an inactive disk name to disk.
When volume is a netmirror volume, even if the stopped node exists, restoration is performed. You cannot use this option by specifying volumes other than a netmirror volume.
Do not use this option other than the procedure described in this manual.
Restores the object even when the highest level group to which disk belongs or the single disk specified by disk includes an active volume.
When volume is a mirror volume, specify a name of lower-level group that is connected to the mirror group to which the volume belongs. This group should have the INVALID mirror slice that needs to be restored to STOP.
Specify a name of the highest-level stripe group when volume is a stripe volume.
Specify a name of the highest-level concatenation group when volume belongs to the highest-level concatenation group.
Specify a name of the volume.
Restores the device information of the disk used for the mirroring among servers that is specified by disk.
Do not use this option other than the procedure described in this manual.
Does not perform a read check in disk area.
When a read check is not necessary, for example, if a disk enters the I/O error state because the path has been removed, you can shorten the recovery process time.
Use this option only when a read check is clearly unnecessary.
Does not perform a read check of the slice specified by the combination of disk and volume, or the combination of group and volume.
Do not use this option other than the procedure described in this manual.
RETURNED VALUE
When it is normally terminated, "0" is returned.
Otherwise, a non-zero value is returned.
