Appendix C Required Disk Space for Performance Management

This appendix explains the required disk space for the performance management with ETERNUS SF Manager.

When the performance management is being performed, based on the fibre channel switch used to collect the performance information, the type of ETERNUS Disk storage system, the number of logical units involved, the number of Disk Enclosures (DEs), and the number of days for which information is to be collected, the required capacity given below becomes necessary.

Information

The default number of days for collection is seven. The number of secured Logical Units (LUs) is the actual number of LUs the functions of which are secured in order to perform performance management for the ETERNUS Disk storage systems. Performance management is secured in units of 64 LUN for the ETERNUS Disk storage systems. Therefore, when instructed to secure from LUN 15 to 200, the information for the actual LUs 0 to 255 (256 in total) would be secured.

Target Device	Required Disk Space (Unit : MB)
ETERNUS DX60 S4/S3	(KeepingDays + 1) * (475 + (1.2 + 0.7 * DEs + 0.4 * (securedLUs + securedRAIDGroups)) * (86400 / perfMonitorInterval) + 0.2 * (86400 / perfMonitorInterval) + (290 * DEs) + (76 * (securedLUs + securedRAIDgroups))) / 1024 1: The securedRAIDGroups is the number of RAIDGroups created from the secured LUs. 2: The performance monitoring interval sets 60 seconds if its interval is set to less than 60 seconds.
ETERNUS DX100 S4/S3 ETERNUS DX200 S4/S3 (*3)	(KeepingDays + 1) * (788 + (2.4 + 0.7 * DEs + 0.2 * NASVolumes + 0.4 * (securedLUs + securedRAIDgroups)) * (86400 / perfMonitorInterval) + 0.2 * (86400 / perfMonitorInterval) + (290 * DEs) + (38 * NASVolumes) + (76 * (securedLUs + securedRAIDgroups))) / 1024 1: The securedRAIDGroups is the number of RAIDGroups created from the secured LUs. 2: The performance monitoring interval sets 60 seconds if its interval is set to less than 60 seconds. 3: When enabling Deduplication/Compression to operate the device, you must add the following capacity to the calculated capacity using the above formula: (KeepingDays + 1) 21.25 MB
ETERNUS DX500 S4/S3 (3) ETERNUS DX600 S4/S3 (3)	(keepingDays + 1) * (2244 + (6.7 + 0.7 * DEs + 0.2 * NASVolumes + 0.5 * (securedLUs + securedRAIDGroups)) * (86400 / perfMonitorInterval) + 0.2 * (86400 / perfMonitorInterval) + (290 * DEs) + (38 * NASVolumes) + (85 * (securedLUs + securedRAIDGroups))) / 1024 1: The securedRAIDGroups is the number of RAIDGroups created from secured LUs. 2: The performance monitoring interval sets 60 seconds if its interval is set to less than 60 seconds. 3: When enabling Deduplication/Compression to operate the device, you must add the following capacity to the calculated capacity using the above formula: (KeepingDays + 1) 37.5 MB
ETERNUS DX8700 S3 ETERNUS DX8900 S3	(keepingDays + 1) * (6913 + (17.8 + 0.7 * DEs + 0.5 * (securedLUs + securedRAIDGroups)) * (86400 / perfMonitorInterval) + 0.2 * (86400 / perfMonitorInterval) + (290 * DEs) + (85 * (securedLUs + securedRAIDGroups))) / 1024 1: The securedRAIDGroups is the number of RAIDGroups created from the secured LUs. 2: The performance monitoring interval sets 60 seconds if its interval is set to less than 60 seconds.
ETERNUS DX60 S2/DX80 S2/DX90 S2 ETERNUS DX60	(keepingDays + 1) * (240 + (1.2 + 0.3 * DEs + 0.3 * (securedLUs + securedRAIDGroups)) * (86400 / perfMonitorInterval) + 3 * (10.6 + 0.07 * (86400 / perfMonitorInterval)) (95 * DEs) + (50 * (securedLUs + securedRAIDGroups))) / 1024 1: The securedRAIDGroups is the number of RAIDGroups created from the secured LUs. 2: The performance monitoring interval sets 60 seconds if its interval is set to less than 60 seconds.
ETERNUS DX400 series	(keepingDays + 1) * (6837 + (17 + 0.2 * DEs + 0.2 * securedLUs + 0.3 * securedRAIDGroups) * (86400 / perfMonitorInterval) + (10.6 + 0.07 * (86400 / perfMonitorInterval)) + (79 * DEs) + (89 * securedLUs) + (103 * securedRAIDGroups)) / 1024 1: The securedRAIDGroups is the number of RAIDGroups created from the secured LUs. 2: The performance monitoring interval sets 60 seconds if its interval is set to less than 60 seconds.
ETERNUS DX400 S2 series ETERNUS DX8000 S2 series	(keepingDays + 1) * (6837 + (17 + 0.2 * DEs + 0.2 * securedLUs + 0.3 * securedRAIDGroups) * (86400 / perfMonitorInterval) + 3 * (10.6 + 0.07 * (86400 / perfMonitorInterval)) + (79 * DEs) + (89 * securedLUs) + (103 * securedRAIDGroups)) / 1024 1: The securedRAIDGroups is the number of RAIDGroups created from the secured LUs. 2: The performance monitoring interval sets 60 seconds if its interval is set to less than 60 seconds.
ETERNUS DX8100	Refer to the formula of ETERNUS DX400 series.
ETERNUS DX8400 ETERNUS DX8700	(keepingDays + 1) * (24090 + (60 + 0.2 * DEs + 0.2 * securedLUs + 0.3 * securedRAIDGroups) * (86400 / perfMonitorInterval) + (10.6 + 0.07 * (86400 / perfMonitorInterval)) + (79 * DEs) + (89 * securedLUs) + (103 * securedRAIDGroups)) / 1024 1: The securedRAIDGroups is the number of RAIDGroups created from the secured LUs. 2: The performance monitoring interval sets 60 seconds if its interval is set to less than 60 seconds.
ETERNUS AF250 S2/AF250 (3) ETERNUS DX200F (3)	(KeepingDays + 1) * (475 + (1.2 + 0.7 * DEs + 0.4 * (securedLUs + securedRAIDGroups)) * (86400 / perfMonitorInterval) + 0.2 * (86400 / perfMonitorInterval) + (290 * DEs) + (76 * (securedLUs + securedRAIDgroups))) / 1024 1: The securedRAIDGroups is the number of RAIDGroups created from the secured LUs. 2: The performance monitoring interval sets 60 seconds if its interval is set to less than 60 seconds. 3: When enabling Deduplication/Compression to operate the device, you must add the following capacity to the calculated capacity using the above formula: (KeepingDays + 1) 21.25 MB
ETERNUS AF650 S2/AF650 (*3)	(keepingDays + 1) * (2244 + (6.7 + 0.7 * DEs + 0.5 * (securedLUs + securedRAIDGroups)) * (86400 / perfMonitorInterval) + 0.2 * (86400 / perfMonitorInterval) + (290 * DEs) + (85 * (securedLUs + securedRAIDGroups))) / 1024 1: The securedRAIDGroups is the number of RAIDGroups created from secured LUs. 2: The performance monitoring interval sets 60 seconds if its interval is set to less than 60 seconds. 3: When enabling Deduplication/Compression to operate the device, you must add the following capacity to the calculated capacity using the above formula: (KeepingDays + 1) 37.5 MB
NetApp FAS Series	(keepingDays + 1) * (0.05 + 14.83 / perfMonitorInterval)
ETERNUS SN200 series Fibre Channel switch (Maximum number of FC ports = 16 or less) PRIMERGY Fibre Channel Switch Blade PRIMERGY Fibre Channel Switch Blade(4Gbps) Brocade Fibre Channel Switch (Maximum number of FC ports = 16 or less)	(keepingDays + 1) * (30 / perfMonitorInterval) * 1.6
ETERNUS SN200 series Fibre Channel switch (Maximum number of FC ports = 32 or less) Brocade Fibre Channel Switch (Maximum number of FC ports = 32 or less)	(keepingDays + 1) * (30 / perfMonitorInterval) * 3.2
ETERNUS SN200 series Fibre Channel switch (Maximum number of FC ports = 128 or less) Brocade Fibre Channel Switch (Maximum number of FC ports = 128 or less)	(keepingDays +1) * (30 / perfMonitorInterval) * 13
ETERNUS SN200 series Fibre Channel switch (Maximum number of FC ports = 256 or less) Brocade Fibre Channel Switch (Maximum number of FC ports = 256 or less)	(keepingDays + 1) * (30 / perfMonitorInterval) * 26
ETERNUS SN200 series Fibre Channel switch (Maximum number of FC ports = 384 or less) Brocade Fibre Channel Switch (Maximum number of FC ports = 384 or less)	(keepingDays + 1) * (30 / perfMonitorInterval) * 39
Brocade VDX series (Maximum transfer rate 10Gbps)	(keepingDays + 1) * (30 / perfMonitorInterval) * ports / 10 *1: The number of mounted ports is the total number of FC Ports and Ethernet Ports (excluding 1GbE RJ45) on the device.
Brocade VDX series (Maximum transfer rate 40Gbps)	(keepingDays + 1) * (30 / perfMonitorInterval) * ports / 9 *1: The number of mounted ports is the total number of FC Ports and Ethernet Ports (excluding 1GbE RJ45) on the device.
ETERNUS SN200 MDS series Fibre Channel switch	(keepingDays + 1) * 0.1 * maxNumberOfSlotsSupportedByDevice * 128 * (30 / perfMonitorInterval) *1: Use 1 as the maximum number of slots for MDS9120

Additionally, when performance information is output using the storageadm perfdata command, the following disk space is required, depending on the number of LUs of ETERNUS Disk storage system and Fibre Channel switches, number of DEs, number of ports that is used to collect performance information, and number of days of performance information output.
Each element (number of installed CM CPUs, number of installed DEs, installed CA Ports, installed CM Ports, LUs, RAIDGroups, installed FC Ports, and installed Ethernet Ports) is the number mounted in the device when the command is executed.

Target Device	Required Disk Space (Unit : MB)
ETERNUS DX60 S4/S3	outputDays * (0.2 + (0.1 + 0.9 * DEs + 0.1 * CAPorts +0.2* (LUs + RAIDGroups)) * (86400 / perfMonitorInterval) + 0.2 * (86400 / perfMonitorInterval) + (1.8 * DEs) + (0.2 * CAPorts) + (0.6 * (LUs+RAIDGroups))) / 1024
ETERNUS DX100 S4/S3 ETERNUS DX200 S4/S3 ETERNUS DX500 S4/S3 ETERNUS DX600 S4/S3	outputDays * (0.4 + (0.1 + 0.9 * DEs + 0.1 * CAPorts + 0.1 * NASVolumes + 0.2 * (LUs + RAIDGroups)) * (86400 / perfMonitorInterval [s] ) + 0.2 * (86400 / perfMonitorInterval) + (1.8 * DEs) + (0.2 * CAPorts) + (0.2 * NASVolumes) + (0.6 * (LUs + RAIDGroups))) / 1024
ETERNUS DX8700 S3 ETERNUS DX8900 S3	outputDays * (1.5 + (0.7 + 0.9 * DEs + 0.1 * CAPorts + 0.2 * (LUs + RAIDGroups) ) * (86400 / perfMonitorInterval) + 0.2 * (86400 / perfMonitorInterval) + (1.8 * DEs) + (0.2 * CAPorts) + (0.6 * (LUs + RAIDGroups))) / 1024
ETERNUS DX60 S2/DX80 S2/DX90 S2 ETERNUS DX60	outputDays * (((0.1 + 0.4 * DEs + 0.1 * CMPorts + 0.2 * (LUs + RAIDGroups)) * (86400 / perfMonitorInterval)) + (0.2 + 0.6 * DEs + 0.2 * CMPorts + 0.4 * (LUs + RAIDGroups))) / 1024
ETERNUS DX400 S2 series ETERNUS DX8000 S2 series ETERNUS DX400 series ETERNUS DX8000 series	outputDays * (((0.1 + 0.2 * DEs + 0.1 * CAPorts + 0.2 * (LUs + RAIDGroups) + 0.1 * CMCPUs) * (86400 / perfMonitorInterval)) + (0.9 + 0.8 * DEs + 0.2 * CAPorts + 0.4 * (LUs + RAIDGroups) + 0.1 * CMCPUs)) / 1024
ETERNUS AF250 S2/AF250 ETERNUS DX200F	outputDays * (0.2 + (0.1 + 0.9 * DEs + 0.1 * CAPorts +0.2* (LUs + RAIDGroups)) * (86400 / perfMonitorInterval) + 0.2 * (86400 / perfMonitorInterval) + (1.8 * DEs) + (0.2 * CAPorts) + (0.6 * (LUs+RAIDGroups))) / 1024
ETERNUS AF650 S2/AF650	outputDays * (0.4 + (0.1 + 0.9 * DEs + 0.1 * CAPorts + 0.2 * (LUs + RAIDGroups)) * (86400 / perfMonitorInterval [s] ) + 0.2 * (86400 / perfMonitorInterval) + (1.8 * DEs) + (0.2 * CAPorts) + (0.6 * (LUs + RAIDGroups))) / 1024
Fibre Channel switches	outputDays * (0.1 + FCPorts + (0.1 * FCPorts)) + (0.1 + ports + (0.1 * FCPorts * (86400 / perfMonitorInterval))) / 1024
Brocade VDX series	outputDays * (0.1 + ports + (0.1 * ports)) + (0.1 + ports + (0.1 * ports * (86400 / perfMonitorInterval))) / 1024 *1: The number of mounted ports is the total number of FC Ports and Ethernet Ports (excluding 1GbE RJ45) on the device.

See

Refer to "Command References" in the ETERNUS SF Storage Cruiser Operation Guide for information on the storageadm perfdata command.