Restrictions in the Cloud Edition are as indicated below.
No. | Restriction | Corrective Action | Release Schedule |
|---|---|---|---|
1 | After an admin server is backed up, it is not possible to recover L-Platforms that have been created, modified, or deleted. | If L-Platforms have been created, modified, or deleted after backup of the admin server, perform backup again. | Next release |
2 | Basic mode cannot be used. | None. | Not yet determined |
3 | iSCSI boot is not possible for physical L-Servers under the following conditions:
| None. | Not yet determined |
4 | It is not possible to change the admin IP address or port number. (This applies to admin servers and agents) | None. | Next release |
5 | Under the following conditions, even if stopping of the server is performed from the "Reconfiguration" page of L-Platform management, reconfiguration cannot be performed.
| None. | Not yet determined |
6 | Under the following conditions, the values input in the "Reconfiguration" page of L-Platform management are displayed and become uneditable, but the reconfiguration is not performed.
| None. | Not yet determined |
7 | Under the following conditions, even though a request to cancel an application has been made, L-Platform operations are not restricted.
| None. | Not yet determined |
8 | In L-Platform subscriptions after saving a configuration, items that have been modified, added, or deleted from the initial settings of the template are not displayed. If an L-Platform subscription is submitted in this situation, these items are also not displayed in the "Details" area of the "Application" tab of the Request tab. | Submit a new L-Platform subscription request without saving the configuration. | Not yet determined |
9 | When the OS of a managed server is Oracle Solaris 11, the following operations cannot be performed for Solaris Zones:
| None. | V3.2.0 (April 2015) Refer to item 5 in "1.1.1 Overview of Additional Functions in V3.2.0". |
10 | On the [L-Platforms] tab of the ROR console, cloning images cannot be collected from servers that use Citrix XenServer for virtualization software, if the VM guest customization function is enabled. | None. | Not yet determined |
11 | In the System Conditions window, not all the information is displayed if a managed VM host is OVM for x86 3.2. | None. | V3.2.0 (April 2015) Refer to item 12 in "1.1.1 Overview of Additional Functions in V3.2.0". |
12 | In the System Conditions window, not all the information is displayed if a managed VM host is Citrix XenServer. | None. | Not yet determined |
13 | The disaster recovery function cannot be used when using a non-default VFAB (Virtual Fabric) for Fujitsu Converged Fabric Switch. | None. | Next release |
14 | When using Firefox, none of the functions of the [Request] tab on the ROR console can be used. | Use Internet Explorer. | V3.2.0 (April 2015) |
15 | When using Firefox, the L-Servers console screen cannot be started from the Resources Tab on the ROR console. | Use Internet Explorer. | Not yet determined |
16 | [Linux Manager] | None. | Not yet determined |
17 | [Linux Manager] | None. | Not yet determined |
18 | When using RHEL-KVM as managed servers, the following configurations are restricted.
| None. | Not yet determined |
19 | PRIMERGY RX4770 M1 cannot be used as resources for physical L-servers. | None. | Next release |
20 | When a PRIMERGY BX2560 M1 is deployed as a physical L-Server, the UMC function cannot be used. | None. | V3.2.0 (T011583LP-01/T011582WP-01) |
21 | When a physical L-Server which uses a single NIC and a BX2560 M1 as the physical server is deleted, the second onboard NIC cannot be used due to port blockage. | When creating a physical L-Server for which a BX2560 M1 is used as the physical server, set two for the number of NICs to be used. | V3.2.0 (T011583LP-01/T011582WP-01) |
22 | The function for guest OS customization cannot be used in OVM for x86 environments. | None. | V3.2.0 (June 2015) Refer to item 15 in "1.1.1 Overview of Additional Functions in V3.2.0". |
23 | When using VMware vSphere 6, the VVOL datastore cannot be used. | Do not register the VVOL datastore in the storage pool as virtual storage. | V3.2.0 (T011583LP-02/T011582WP-02) Refer to item 2 in "1.1.3 Overview of Additional Functions in V3.2.0 (T011583LP-02/T011582WP-02)". |
24 | When using VMware vSphere 6, the following information of the VM pool is not correctly displayed.
| Check the available memory of the VMware vSphere 6 VM host on VMware vCenter Server. | Not yet determined |
25 | The functions for exporting and importing VMware vSphere 6 virtual L-Servers cannot be used. | None. | V3.2.0 (T011583LP-02/T011582WP-02) Refer to item 2 in "1.1.3 Overview of Additional Functions in V3.2.0 (T011583LP-02/T011582WP-02)". |
26 | When using VMware vSphere 6, the following resources are not restored by the DR Option.
| None. | Not yet determined |
27 | When using the servers below in configurations where port expansion options or CNA cards with Universal Multi-Channel (UMC) functions are mounted, it is not possible to create physical L-Servers (including physical L-Server creation in L-Platform deployment).
| None. | Not yet determined |
