2.1 Supported Devices

This section describes devices that are supported by Express, Storage Cruiser and AdvancedCopy Manager.

Devices Supported by Express

Express supports the following storage devices:

ETERNUS DX60/DX80/DX90
ETERNUS DX60 S2/DX80 S2/DX90 S2
ETERNUS DX60 S3/DX100 S3/DX200 S3
ETERNUS DX200F

Note

The firmware versions of storage devices must be as shown in the table below. However, for unlisted storage devices, there is no limit for the firmware version number.

Table 2.1 Storage Devices and Compatible Firmware Version
Storage Device Name	Compatible Firmware Version
ETERNUS DX60/DX80/DX90	V10L31 or later
ETERNUS DX60 S2	V20L10 or later
ETERNUS DX80 S2/DX90 S2	V10L16 or later

For using Remote Advanced Copy between ETERNUS DX90 and ETERNUS DX90 S2, the firmware version of ETERNUS DX90 must be updated to V10L61 or later.

Enable the following settings for the interface to storage devices.

Table 2.2 Storage Devices and Interface Settings
Storage Device Name	Interface Settings
ETERNUS DX60/DX80/DX90 ETERNUS DX60 S2	Telnet connection
ETERNUS DX80 S2/DX90 S2 ETERNUS DX60 S3/DX100 S3/DX200 S3	SSH connection
ETERNUS DX200F	SSH connection

Devices Supported by Storage Cruiser

Storage Cruiser supports the following devices.

Device Type	Device Name
Storage device	ETERNUS DX series ETERNUS DX200F ETERNUS CS800, ETERNUS CS2000 ETERNUS VS850 NetApp FAS Series NetApp FAS Series (with clustered Data ONTAP) NetApp V-Series NetApp V-Series (with clustered Data ONTAP) Tintri VMstore series (*1)
Tape library	ETERNUS LT series
Fibre Channel switch	ETERNUS SN200 PRIMERGY BX600 Fibre Channel Switch Blade Brocade series
Converged Switch	Brocade VDX series PRIMERGY BX Ethernet Fabric Switch
Others	Solaris, Windows, Linux, HP-UX, and AIX server nodes VMware vSphere 4 or later

*1: It is only when the operating system of Management Server is Windows that the Tintri VMstore series can be monitored.

Note

The firmware versions of storage devices must be as shown in the table below. However, for unlisted storage devices, there is no limit for the firmware version number.
Table 2.3 Storage Devices and Compatible Firmware Version
Storage Device Name
Compatible Firmware Version
ETERNUS DX80 S2/DX90 S2
V10L16 or later
ETERNUS DX400 S2 series
V10L16 or later

Table 2.3 Storage Devices and Compatible Firmware Version
Storage Device Name	Compatible Firmware Version
ETERNUS DX80 S2/DX90 S2	V10L16 or later
ETERNUS DX400 S2 series	V10L16 or later

Enable the following settings for the interface to storage devices.

Table 2.4 Storage Devices and Interface Settings
Storage Device Name	Interface Settings
ETERNUS DX60/DX80/DX90 ETERNUS DX60 S2	Telnet connection
ETERNUS DX S2 series (excluding DX60 S2) ETERNUS DX S3 series	SSH connection
ETERNUS DX200F	SSH connection

When using the reporting function, use the following storage devices and firmware version.

Table 2.5 Storage Devices and Compatible Firmware Version
Storage Device Name	Compatible Firmware Version
ETERNUS DX S2 series (excluding DX60 S2)	V10L40 or later
ETERNUS DX S3 series	All versions
ETERNUS DX200F	All versions

When using the Storage Cluster function, use the following storage devices and firmware version. In addition, equalize the firmware version for Primary Storage and Secondary Storage constituting the Storage Cluster environment.

Table 2.6 Storage Devices and Compatible Firmware Version
Storage Device Name	Compatible Firmware Version
ETERNUS DX100 S3/DX200 S3 ETERNUS DX500 S3/DX600 S3	V10L20 or later (*1)
ETERNUS DX8700 S3/DX8900 S3	V10L40 or later
ETERNUS DX200F	V10L30 or later

*1: To use the Automatic Failback function, V10L30 or later firmware is required.

Devices Supported by AdvancedCopy Manager

AdvancedCopy Manager supports the following ETERNUS Disk storage systems:

ETERNUS DX series
ETERNUS DX200F

Note

The firmware versions of storage devices must be as shown in the table below. However, for unlisted storage devices, there is no limit for the firmware version number.

Table 2.7 Storage Devices and Compatible Firmware Version
Storage Device Name	Compatible Firmware Version
ETERNUS DX60/DX80/DX90	V10L31 or later
ETERNUS DX60 S2	V20L10 or later
ETERNUS DX80 S2/DX90 S2	V10L16 or later

For using Remote Advanced Copy between DX90 and DX90 S2, the firmware version of DX90 must be updated to V10L61 or later.

Enable the following settings for the interface to storage devices.

Table 2.8 Storage Devices and Interface Settings
Storage Device Name	Interface Settings
ETERNUS DX60/DX80/DX90 ETERNUS DX 60 S2	Telnet connection
ETERNUS DX S2 series (excluding DX60 S2) ETERNUS DX S3 series	SSH connection
ETERNUS DX200F	SSH connection

Information

With AdvancedCopy Manager CCM, the devices listed below can use Copy command via SAN and via LAN.

Table 2.9 ETERNUS Disk Storage Systems Supporting Copy Command via SAN and/or via LAN
Device Name	Copy Command via SAN		Copy Command via LAN
Device Name	Operation	Firmware Version	Operation	Firmware Version
ETERNUS DX60 ETERNUS DX80	A	All versions	N/A	-
ETERNUS DX90	A	All versions	A (*1)	V10L61 or later
ETERNUS DX400 series ETERNUS DX8000 series	A	All versions	A (*1)	V20L71 or later
ETERNUS DX60 S2	A	All versions	N/A	-
ETERNUS DX S2 series (excluding DX60 S2)	A	All versions	A	All versions
ETERNUS DX S3 series	A	All versions	A	All versions
ETERNUS DX200F	A	All versions	A	All versions

(A=Available, N/A=Not Available)

*1: The acarray add command of AdvancedCopy Manager CCM cannot be executed with the -lan option.

Refer to "System Configuration" in the ETERNUS SF AdvancedCopy Manager Operation Guide for Copy Control Module for information on Copy command via SAN and via LAN.