2.5.3 NAS resource creation (NetApp Filer(7-Mode) is used)

When you return to the NAS turnkey wizard, select Netapp.

Settings of turnkey wizard "NAS"
 1) HELP                              12) Crm:SystemState2(-)
 2) -                                 13) LocalFileSystems(-)
 3) SAVE+EXIT                         14) RemoteFileSystems(-)
 4) -                                 15) IpAddresses(-)
 5) ApplicationName=APP1              16) RawDisks(-)
 6) Machines+Basics(app1)             17) RC-VolumeManagement(-)
 7) CommandLines(-)                   18) VERITAS-VolumeManagement(-)
 8) Controllers(-)                    19) Netapp(-)
 9) Crm:Application(-)                20) Eternusdx(-)
10) Crm:BasicApplication(-)           21) Gds:Global-Disk-Services(-)
11) Crm:SystemState3(-)               22) Gls:Global-Link-Services(-)
Choose the setting to process: 19

When the Netapp wizard is displayed, select AdditionalNetAppFiler.

Netapp (Netapp_APP1:not yet consistent)
 1) HELP
 2) -
 3) SAVE+EXIT
 4) REMOVE+EXIT
 5) AdditionalNetAppFiler
 6) AdditionalUnlockMachines
 7) (PreOnlineScript=)
 8) (PostOnlineScript=)
 9) (PreOfflineScript=)
10) (PostOfflineScript=)
11) (FaultScript=)
12) NetappClusterFlag=no
Choose the setting to process: 5

When the following menu is displayed, select FREECHOICE and enter a host name for NAS.

1) HELP
2) RETURN
3) FREECHOICE
Set an additional NetApp Filer: 3
        >> netapp1

When the following menu is displayed, select AdditionalExportpoint.

1) HELP
2) NO-SAVE+RETURN
3) -
4) AdditionalExportpoint
5) UnLockFlag=always
6) ExportFlag=no
7) UnExportFlag=no
8) ScriptTimeout=300
9) Mode=7-Mode
Choose the setting to process: 4

When the following menu is displayed, select FREECHOICE and enter a volume to be exported.

1) HELP
2) RETURN
3) FREECHOICE
Set an additional export point: 3
        >> /vol/vol1

The following menu is displayed. If you have any further volumes to be exported, select AdditionalExportpoint to add.

 1) HELP
 2) NO-SAVE+RETURN
 3) SAVE+RETURN
 4) AdditionalExportpoint
 5) UnLockFlag=always
 6) ExportFlag=no
 7) UnExportFlag=no
 8) ScriptTimeout=300
 9) Mode=7-Mode
10) Exportpoint[0]=/vol/vol1
Choose the setting to process:

The following operations are available from the above menu:

Attributes	Description
UnLockFlag	Select whether or not Unlock processing should be executed on NAS. Selecting "always" constantly enables Unlock processing in the event of a Netapp resource failure and a node with the Netapp resource is down. Selecting "nodedown" enables Unlock processing only when the node with the Netapp resource is down. Default: always (always, nodedown)
ExportFlag	Select whether or not Export processing is executed during Online processing. Selecting "yes" enables Export processing during Online processing with "anon=0" option. Selecting "no" disables Export processing during Online processing. It is necessary to export volumes as described in "exportfs setup" of "2.4 NAS configuration". Default: no (yes, no)
UnExportFlag	Select whether or not Unexport processing should be executed during Offline processing in standby operation. Selecting "yes" enables Unexport processing during Offline processing. Selecting "no" disables Unexport processing during Offline processing. In scalable operation, Unexport processing is disabled regardless this option. UnExportFlag is valid when ExportFlag is set to "yes". Default: no (yes, no)
ScriptTimeout	Specify timeout period (sec) for launching of Online/Offline processing. Normally, you do not need to change the default value. Default: 300 (10-31536000)
Mode	When NetApp Filer(7-Mode) is used, set to "7-Mode". When NetApp Filer(cDOT) is used, set to "cDOT". You have to set "7-Mode". Default: 7-Mode (7-Mode, cDOT)

If addition is complete, select SAVE+RETURN.
You return to the Netapp Wizard. If you want to add any further NAS device, select AdditionalNetAppFiler. When NetApp Filer(7-Mode) is used, do not select AdditionalUnlockMachines.

It is set for script files in Netapp resource also start and stop. If it is not necessary, go to next step.

Netapp (Netapp_APP1:consistent)
 1) HELP
 2) -
 3) SAVE+EXIT
 4) REMOVE+EXIT
 5) AdditionalNetAppFiler
 6) NetAppFiler[0]=netapp1
 7) AdditionalUnlockMachines
 8) (PreOnlineScript=)
 9) (PostOnlineScript=)
10) (PreOfflineScript=)
11) (PostOfflineScript=)
12) (FaultScript=)
13) NetappClusterFlag=no
Choose the setting to process:

Attributes	Description
PreOnlineScript	Executed before Online processing.
PostOnlineScript	Executed after Online processing.
PreOfflineScript	Executed before Offline processing.
PostOfflineScript	Executed after Offline processing.
FaultScript	Executed when a fault occurs.

See

For further details, see the "PRIMECLUSTER Reliant Monitor Services (RMS) with Wizard Tools Configuration and Administration Guide".

Next, it is set for PRIMECLUSTER to control the NetApp Filer cluster if necessary. In the cluster composition of the NAS device, if network failure between the cluster node and the NAS device is detected PRIMECLUSTER Wizard for NAS can execute failover (cf takeover) of the NetApp Filer-Cluster.
Selects NetappClusterFlag for monitoring the NetApp Filer-Cluster.
```
Netapp (Netapp_APP1:consistent)
 1) HELP
 2) -
 3) SAVE+EXIT
 4) REMOVE+EXIT
 5) AdditionalNetAppFiler
 6) NetAppFiler[0]=netapp1
 7) AdditionalUnlockMachines
 8) (PreOnlineScript=)
 9) (PostOnlineScript=)
10) (PreOfflineScript=)
11) (PostOfflineScript=)
12) (FaultScript=)
13) NetappClusterFlag=no
Choose the setting to process: 13
```
Attributes
Description
NetappClusterFlag
It is set for control facility of the NetApp Filer-Cluster.
Default: no (yes, no)

Note
Default is no. Set no to NetappClusterFlag if control facility of the NetApp Filer-Cluster is not necessary, when you use a clustered NAS.

Attributes	Description
NetappClusterFlag	It is set for control facility of the NetApp Filer-Cluster. Default: no (yes, no)

If you use NetApp Filer-Cluster, select yes.

Setting menu : NetappClusterFlag for Netapp
1) HELP
2) RETURN
3) yes
4) no
NetappCluster flag for Netapp: 3

Set parameters.

Netapp (Netapp_APP1:not yet consistent)
 1) HELP                              10) (PreOfflineScript=)
 2) -                                 11) (PostOfflineScript=)
 3) SAVE+EXIT                         12) (FaultScript=)
 4) REMOVE+EXIT                       13) NetappClusterFlag=yes
 5) AdditionalNetAppFiler             14) NetappClusterDeviceName=
 6) NetAppFiler[0]=netapp1            15) NetappClusterManagementDeviceName= 
 7) AdditionalUnlockMachines          16) NetappClusterPingCount=10 
 8) (PreOnlineScript=)                17) NetappClusterPingTimeout=5
 9) (PostOnlineScript=)               18) NetappClusterPingInterval=5
Choose the setting to process:

Attributes	Description
NetappClusterDeviceName	The NAS device name (host name) is specified. Delimit by ":" and specify two NAS device names. example: netapp1:netapp2
NetappClusterManagementDeviceName	Do not set when you use NetApp Filer(7-Mode).
NetappClusterPingCount	The execution frequency of the ping command is specified. Default: 10 (1 - 60)
NetappClusterPingTimeout	The time-out time (sec) for launching of the ping command is specified. Default: 5 (1 - 300)
NetappClusterPingInterval	The execution interval (sec) of the ping command is specified. Default: 5 (1 - 300)

Note

These attributes is set for each userApplication.

The NAS device is monitored by the ping command.
In this step, it is possible to set the execution frequency, the time-out time, and the execution interval of the ping command executed in fixed-cycle monitoring. It is recommended these parameters are used like default.

Do not mix the NAS device name of IPv4 and NAS device name of IPv6 in NetappClusterDeviceName.

See

Refer to "Appendix B Turning of the control facility for the NetApp Filer-Cluster" for the parameter of the ping command.

When the setting is completed, SAVE+EXIT is selected.

Netapp (Netapp_APP1:consistent)
 1) HELP
 2) -
 3) SAVE+EXIT
 4) REMOVE+EXIT
 5) AdditionalNetAppFiler
 6) NetAppFiler[0]=netapp1
 7) AdditionalUnlockMachines
 8) (PreOnlineScript=)
 9) (PostOnlineScript=)
10) (PreOfflineScript=)
11) (PostOfflineScript=)
12) (FaultScript=)
13) NetappClusterFlag=yes
14) NetappClusterDeviceName=netapp1:netapp2
15) NetappClusterManagementDeviceName=
16) NetappClusterPingCount=10
17) NetappClusterPingTimeout=5
18) NetappClusterPingInterval=5
Choose the setting to process: 3