An invalid argument was specified.
Explanation
An invalid argument has been specified.
System action
The system terminates processing.
System administrator response
Check the valid values for the argument, and execute the command again.
An invalid option was specified. option=option
Explanation
An invalid option has been specified.
Parameters
option : Specified option
System action
The system terminates processing.
System administrator response
Check the valid values for the option, and execute the command again.
An invalid parameter was specified. option=option, parameter=parameter
Explanation
An invalid parameter has been specified. The reason is either of the following.
The parameter of the option shown in option is incorrect.
The parameter of the option shown in option and the parameter of other option are inconsistent.
Parameters
option : Specified option
parameter : Specified parameter
System action
The system terminates processing.
System administrator response
Perform one of the following actions:
Check the specification of the option shown in option. Specify the correct value with the parameter, and execute the command again.
Check the conditions can be specified with between the parameter of the option shown in option and the parameter of other option. Specify the correct value with each parameter, and execute the command again.
An invalid option was specified for the copy type. copy group=copyGroup, copy type=copyType, option=option
Explanation
An invalid option has been specified for a copy group.
Parameters
copyGroup : Copy group name
copyType : Copy type
option : Specified option
System action
The system terminates processing.
System administrator response
Check the valid values for the copy type, and execute the command again.
This command requires operating system's administrative privileges.
Explanation
This command can only be executed with Administrator privileges.
System action
The system terminates processing.
System administrator response
Execute the command as a user with Administrator privileges.
The license is not registered.
Explanation
The license has not been registered yet.
System action
The system terminates processing.
System administrator response
Register the license, and execute the command again.
The specified disk array is already registered. disk array=arrayName
Explanation
Information for the specified ETERNUS Disk storage system has already been registered.
Parameters
arrayName : ETERNUS name or ETERNUS Disk storage system IP address
System action
The system terminates processing.
System administrator response
Confirm the existing ETERNUS Disk storage system information (ETERNUS name, Box ID and IP address of ETERNUS Disk storage system) by executing the acarray list command. Refer to the ETERNUS SF Operation Guide for Copy Control Module for information on the command.
The specified copy group is already registered. copy group=copyGroup
Explanation
The copy group has already been registered.
Parameters
copyGroup : Copy group name
System action
The system terminates processing.
System administrator response
Execute the command again, specifying a copy group name that has not been registered yet.
The specified copy pair already registered. copy group=copyGroup, pair=copyPair
Explanation
The copy pair has already been registered.
Parameters
copyGroup : Copy group name
copyPair : Copy pair name
System action
The system terminates processing.
System administrator response
Execute the command again, specifying a copy pair name that has not been registered yet.
An invalid copy pair was specified. pair=copyPair, detail=detail
Explanation
An invalid copy pair has been specified.
Parameters
copyPair : Copy pair name
detail : Detailed information about the cause of the error
The detail is will be one of the following strings:
Strings Displayed in detail | Error Cause |
|---|---|
invalid format | The format of the copy pair is incorrect. |
invalid disk array | The specified ETERNUS Disk storage system has not been set up for the copy group. |
same disk array | The same ETERNUS Disk storage system has been specified for both the copy source and the copy destination. |
invalid copy direction | The copy direction is not the same as the other copy pairs that have already been added to the copy group. |
invalid Snap Data Volume | The copy destination logical volume of the specified copy pair is not Snap Data Volume. |
old disk array info | The required ETERNUS Disk storage system re-registration needed by the upgrade procedure has not been performed. |
System action
The system terminates processing.
System administrator response
The action required depends on the detail string, as described below:
Strings Displayed in detail | Action Plan |
|---|---|
invalid format | Execute the command again, specifying a correct format for the copy pair. |
invalid disk array | Execute the command again, specifying the ETERNUS Disk storage system that has been set up for the copy group. |
same disk array | Execute the command again, specifying different ETERNUS Disk storage system for the copy source and the copy destination. |
invalid copy direction | Execute the command again, using the same copy direction as for the other copy pairs that have already been added to the copy group. |
invalid Snap Data Volume | Execute the command again, specifying the Snap Data Volume for the copy destination logical volume. |
old disk array info | Execute the command again, after the re-registration of ETERNUS Disk storage system by referring to the following manual. |
An invalid volume is specified. volume=volumeName, detail=detail
Explanation
An invalid logical volume is specified.
Parameters
volumeName : Logical volume name
detail : Detailed information about the cause of the error
The detail is will be one of the following strings:
Strings Displayed in detail | Error Cause |
|---|---|
invalid format | The format of the logical volume is incorrect. |
System action
The system terminates processing.
System administrator response
The action required depends on the detail string, as described below:
Strings Displayed in detail | Action Plan |
|---|---|
invalid format | Confirm the format of logical volume. Then, execute the command again, specifying a correct format. |
The number of generation is exceeded the registerable number. Maximum Number of Generation=maxNumber
Explanation
The number of generation that can be registered is exceeded.
Parameters
maxNumber : Maximum number of generation that can be registered
System action
The system terminates processing.
System administrator response
Check whether the number of copy pairs that have the same copy source logical volume is exceeded the maximum number or not.
The REC buffer could not be found. ID=bufferID
Explanation
The specified buffer ID does not exist.
Parameters
bufferID : REC transfer buffer ID
System action
The system terminates processing.
System administrator response
Execute the command again, specifying the correct ID.
An invalid access volume is specified. access volume=volumeName, detail=detail
Explanation
An invalid access volume is specified.
Parameters
volumeName : Access volume
detail : Detailed information about the cause of the error
The DETAIL is will be one of the following strings:
Strings Displayed in detail | Error Cause |
|---|---|
invalid access volume | The access volume is incorrect. |
System action
The system terminates processing.
System administrator response
The action required depends on the detail string, as described below:
Strings Displayed in detail | Action Plan |
|---|---|
invalid access volume | Execute the command again, specifying the access volume of the specifying ETERNUS Disk storage system. |
The remote ETERNUS disk storage system is defined in the specified copygroup. remote disk storage system= arrayName
Explanation
The remote ETERNUS Disk storage system is defined for the specified copy group.
Parameters
arrayName : Name of ETERNUS Disk storage system
System action
The system terminates processing.
System administrator response
Check that the specified ETERNUS Disk storage system is not remote ETERNUS Disk storage system.
Appropriate action using the command:
To display the list of remote ETERNUS Disk storage system, execute the acarray list command with -remote option. Refer to the ETERNUS SF Operation Guide for Copy Control Module for information on the command.
Appropriate action using the Web Console:
On the global navigation tab, click Storage.
The registered ETERNUS Disk storage systems are displayed on the Main pane.
On the Main pane, click the target ETERNUS Disk storage system.
On the Category pane, click Advanced Copy.
The information related to Advanced Copy is displayed on the Main pane.
On the Main pane, check that "Using as remote partner (REC)" is not displayed in Copy Control Type field.
The specified disk array does not exist. disk array=arrayName
Explanation
There is no information for the specified ETERNUS Disk storage system.
Parameters
arrayName : ETERNUS name
System action
The system terminates processing.
System administrator response
Appropriate action using the command:
Execute the acarray list command to check whether the specified ETERNUS name is correct. Refer to the ETERNUS SF Operation Guide for Copy Control Module for information on the command.
Appropriate action using the Web Console:
On the global navigation tab, click Storage.
The registered ETERNUS Disk storage systems are displayed on the Main pane.
On the Main pane, click the target ETERNUS Disk storage system.
On the Category pane, click Advanced Copy.
The information related to Advanced Copy is displayed on the Main pane.
On the Main pane, check whether the correct connection type is set in Copy Control Type field.
The specified disk array does not exist. disk array=boxID
Explanation
There is no information for the specified ETERNUS Disk storage system.
Parameters
boxID : Box ID of ETERNUS Disk storage system
System action
The system terminates processing.
System administrator response
The information for the ETERNUS Disk storage system specified by the boxID has been deleted.
Register the same Box ID information for the specified ETERNUS Disk storage system again, and execute the command again.
The specified copy group was not found. copy group=copyGroup
Explanation
The specified copy group has not been set up.
Parameters
copyGroup : Copy group name
System action
The system terminates processing.
System administrator response
Appropriate action using the command:
Execute the acgroup list command to check whether the specified copy group name is correct. Refer to the ETERNUS SF Operation Guide for Copy Control Module for information on the command.
Appropriate action using the Web Console:
On the global navigation tab, click Storage.
The registered ETERNUS Disk storage systems are displayed on the Main pane.
On the Main pane, click the target ETERNUS Disk storage system.
On the Category pane, click Advanced Copy.
On the Advanced Copy pane, click Copy Group.
The created copy group list is displayed on the Main pane.
Check whether the specified copy group is correct.
No copy pair was found for the specified copy group. copy group=copyGroup
Explanation
The copy pair has not been set up for the specified copy group.
Parameters
copyGroup : Copy group name
System action
The system terminates processing.
System administrator response
Set up the copy pair for the specified copy group, and execute the command again.
The specified copy pair was not found. copy group=copyGroup, pair=copyPair
Explanation
The specified copy pair has not been set up for the copy group.
Parameters
copyGroup : Copy group name
copyPair : Copy pair name
System action
The system terminates processing.
System administrator response
Set up the specified copy pair for the copy group, and execute the command again.
The specified logical volume was not found. logical volume=volumeName
Explanation
The specified logical volume does not exist.
Parameters
volumeName : Logical volume name
System action
The system terminates processing.
System administrator response
Execute the command again, specifying an existing logical volume.
An invalid copy group was specified. copy group=copyGroup, copy type=copyType
Explanation
The operation that the user is trying to execute cannot be performed on the specified copy group.
Parameters
copyGroup : Specified copy group
copyType : Copy type set in the copy group
System action
The system terminates processing.
System administrator response
Check the copy type that has been set up for the specified copy group.
The logical volume is not found. copy group=copyGroup, logical volume=volumeName
Explanation
The specified logical volume does not exist.
Parameters
copyGroup : specified copy group
volumeName : Logical volume name
System action
The system terminates processing.
System administrator response
Execute the command again, specifying an existing copy source logical volume in the specified copy group.
Remote ETERNUS Disk storage system cannot be specified. disk array=arrayName
Explanation
The remote ETERNUS Disk storage system cannot be specified.
Parameters
arrayName : Name of ETERNUS Disk storage system
System action
The system terminates processing.
System administrator response
Check that the specified ETERNUS Disk storage system is not remote ETERNUS Disk storage system.
Appropriate action using the command:
To display the list of remote ETERNUS Disk storage system, execute the acarray list command with -remote option. Refer to the ETERNUS SF Operation Guide for Copy Control Module for information on the command.
Appropriate action using the Web Console:
On the global navigation tab, click Storage.
The registered ETERNUS Disk storage systems are displayed on the Main pane.
On the Main pane, click the target ETERNUS Disk storage system.
On the Category pane, click Advanced Copy.
The information related to Advanced Copy is displayed on the Main pane.
On the Main pane, check that "Using as remote partner (REC)" is not displayed in Copy Control Type field.
An access volume could not be found. disk storage system=arrayName
Explanation
An access volume could not be found.
Parameters
arrayName : ETERNUS name
System action
The system terminates processing.
System administrator response
Confirm that the specified ETERNUS Disk storage system has a valid access volume.
The directory could not be found. directory=dirName
Explanation
The specified directory is not found.
Parameters
dirName : Directory name
System action
The system terminates processing.
System administrator response
Confirm that the directory actually exists, or check whether the directory name is correct. Then, execute the command again.
Session does not exist. function=function (status)
Explanation
The session does not exist.
Parameters
function : Function name
status : Advanced Copy status information
System action
The system terminates processing.
System administrator response
An operation has been executed regarding a copy pair where a session does not exist.
Confirm the session status.
Session already exists. function=function (status)
Explanation
The session already exists.
Parameters
function : Function name
status : Advanced Copy status information
System action
The system terminates processing.
System administrator response
An operation has been executed regarding a copy pair where a session already exists.
Check the session status, and restart the operation when there is no more session.
Operation sequence error. function=function (status)
Explanation
The system is not in a status where the specified operation can be executed.
Parameters
function : Function name
status : Advanced Copy status information
System action
The system terminates processing.
System administrator response
An operation has been executed regarding a copy pair which is in a state where the specified operation cannot be executed.
Confirm the session status.
Synchronization processing is not in equivalency held state. function=function (status)
Explanation
The system has not reached equivalency state yet.
Parameters
function : Function name
status : Advanced Copy status information
System action
The system terminates processing.
System administrator response
Execute again after the system has reached equivalency state.
The synchronization processing in an opposite direction to the specified one is in progress. function=function (status)
Explanation
A synchronization operation in the opposite direction from the specified direction is currently in progress.
Parameters
function : Function name
status : Advanced Copy status information
System action
The system terminates processing.
System administrator response
Check the status of the synchronization operation, and execute again.
LAN connection ETERNUS Disk storage system cannot be specified. disk array=arrayName
Explanation
The ETERNUS Disk storage system connected with LAN cannot be specified.
Parameters
arrayName : Name of ETERNUS Disk storage system
System action
The system terminates processing.
System administrator response
Check that the specified ETERNUS Disk storage system is not connected with LAN.
Appropriate action using the command:
To confirm the detail information of ETERNUS Disk storage system, execute the acarray detail command with -route option. Refer to the ETERNUS SF Operation Guide for Copy Control Module for information on the command.
Appropriate action using the Web Console:
On the global navigation tab, click Storage.
The registered ETERNUS Disk storage systems are displayed on the Main pane.
On the Main pane, click the target ETERNUS Disk storage system.
On the Category pane, click Advanced Copy.
The information related to Advanced Copy is displayed on the Main pane.
On the Main pane, check that "Access through network" is not displayed in Copy Control Type field.
Session does not exist.
Explanation
The session does not exist.
System action
The system terminates processing.
System administrator response
No session that could be used for the operation exists, or the operation has been executed regarding a volume where no session exists.
Confirm the session status.
An input error occurred. detail=detail
Explanation
An input error occurred.
Parameters
detail : Detailed information about the cause of the error
System action
The system terminates processing.
System administrator response
The action required depends on the detail string, as described below:
Strings Displayed in detail | Action Plan |
|---|---|
input is empty | Input is empty. Input a correctly formatted value. |
invalid column number (line=line,number=number) | Input at the line is invalid. The number of columns separated by a Tab character is allowed with 1 or 2. |
invalid format (line=line,column=column,value=value) | The format of column at line is invalid. Input a correctly formatted value. |
io error | An I/O error occurred. It occurs when the command is cancelled during input. Execute the operation again. |
The operation cannot be performed because the copy status of the volume in the group is different.
Explanation
The operation cannot be performed because the copy status of the volume in the group is different.
System action
The system terminates processing.
System administrator response
Review the operational status of each volume in the group and re-execute the command.
In order to create a replica of the Concurrent OPC using QuickOPC, all the volumes in the group must be tracking or not tracked.
Operation aborted. The configuration file is in use.
Explanation
Processing was interrupted because an AdvancedCopy Manager Copy Control Module configuration file was being used.
System action
The system terminates processing.
System administrator response
This message is output if one of the commands listed below and other AdvancedCopy Manager Copy Control Module command are executed at the same time. (Including the confliction between commands listed below)
Wait for the conflicting AdvancedCopy Manager Copy Control Module command to finish. Then, execute the command again.
acarray add
acarray change
acarray remove
acgroup create
acgroup remove
acpair add
acpair remove
If you are using the Web Console, wait the processing of an operation which output this message for a while. Then, execute again.
Operation failed. function=function, message=message
Explanation
The process has failed.
Parameters
function : Process name
message : Message
System action
The system terminates processing.
System administrator response
Take the appropriate action according to the error message.
Operation failed. function=function, message=message
Explanation
The process has failed.
Parameters
function : Process name
message : Message
System action
The system terminates processing.
System administrator response
Take the appropriate action indicated by "Appendix A Detailed Messages" section shown in message.
Operation failed. function=function, message=message
Explanation
The process has failed.
Parameters
function : Process name
message : Message
System action
The system terminates processing.
System administrator response
Take the appropriate action indicated by "Appendix A Detailed Messages" section shown in message.
An invalid mount point was specified. mount point=mountPoint
Explanation
An invalid mount point or drive letter has been specified.
Parameters
mountPoint : Mount point or drive letter
System action
The system terminates processing.
System administrator response
Check the mount point or drive letter by executing the acgetvolinfo command, and execute the command again. Refer to the ETERNUS SF Operation Guide for Copy Control Module for information on the command.
An invalid device was specified. device=deviceName
Explanation
An invalid device has been specified.
Parameters
deviceName : Device
System action
The system terminates processing.
System administrator response
Devices must be specified using the following format: "PhysicalDrive [deviceNumber]". Execute the command again, specifying a valid format for the device.
The target logical volume is write protected. target logical volume=volumeName
Explanation
The copy destination logical volume is protected.
Parameters
volumeName : Copy destination logical volume
System action
The system terminates processing.
System administrator response
Release the copy destination logical volume protection settings, and execute the command again.
The target logical volume is write protected. target logical volume=volumeName
Explanation
The copy destination logical volume is protected.
Parameters
volumeName : Copy destination logical volume
System action
The system continues processing.
System administrator response
No response is required.
A general system function failed. function=function, error=error
Explanation
The execution of a system function has failed.
Parameters
function : System function
error : Error content
System action
The system terminates processing.
System administrator response
Collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to Collect Data" in the ETERNUS SF Operation Guide for Copy Control Module
Could not open the registry. registry key=keyName
Explanation
Opening a registry has failed.
Parameters
keyName : Registry key name
System action
The system terminates processing.
System administrator response
Collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to collect data" in the ETERNUS SF Operation Guide for Copy Control Module
Could not open the file. file=fileName
Explanation
Opening a file has failed.
Parameters
fileName : File name
System action
The system terminates processing.
System administrator response
Check the status of the file system.
If the file system is normal, collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to collect data" in the ETERNUS SF Operation Guide for Copy Control Module
Could not write the file. file=fileName
Explanation
Writing to a file has failed.
Parameters
fileName : File name
System action
The system terminates processing.
System administrator response
Check the status of the file system.
If the file system is normal, collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to collect data" in the ETERNUS SF Operation Guide for Copy Control Module
Could not delete the file. file=fileName
Explanation
Deleting a file has failed.
Parameters
fileName : File name
System action
The system terminates processing.
System administrator response
Check the status of the file system.
If the file system is normal, collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to collect data" in the ETERNUS SF Operation Guide for Copy Control Module
Could not start Java VM.
Explanation
Starting the Java VM has failed.
System action
The system terminates processing.
System administrator response
Collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to collect data" in the ETERNUS SF Operation Guide for Copy Control Module
A memory allocation failed.
Explanation
Allocating a memory area has failed.
System action
The system terminates processing.
System administrator response
Check the memory usage status.
If there is not enough memory, increase it.
If there is enough memory, collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to collect data" in the ETERNUS SF Operation Guide for Copy Control Module
Could not read the file. file=fileName
Explanation
Reading a file has failed.
Parameters
fileName : File name
System action
The system terminates processing.
System administrator response
Check the status of the file system.
If the file system is normal, collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to collect data" in the ETERNUS SF Operation Guide for Copy Control Module
License Manager is not installed.
Explanation
The program of the license management function has not been installed.
The system environment may be broken.
System action
The system terminates processing.
System administrator response
Install the ETERNUS SF Manager or AdvancedCopy Manager Copy Control Module again.
The configuration file has an invalid format. file=fileName
Explanation
The content of the configuration file is invalid.
Parameters
fileName : File name
System action
The system terminates processing.
System administrator response
Collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to collect data" in the ETERNUS SF Operation Guide for Copy Control Module
An error occurred in accessing the Java property file. property=propertyName
Explanation
A Java property could not be looked up.
Parameters
propertyName : Property name
System action
The system terminates processing.
System administrator response
Collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to collect data" in the ETERNUS SF Operation Guide for Copy Control Module
An unexpected error occurred.
Explanation
A system error has occurred.
System action
The system terminates processing.
System administrator response
Collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to collect data" in the ETERNUS SF Operation Guide for Copy Control Module
Failed to access the directory. directory=dirName
Explanation
One of the following has occurred:
The node on which the command was executed is not an operational node.
The directory does not exist.
Parameters
dirName : Directory name
System action
The system terminates processing.
System administrator response
If the node on which the command was executed is not an operational node, execute the command on the operational node again.
If the directory does not exist, refer to "Customization for CCM Server Transactions" in the ETERNUS SF Cluster Environment Setup Guide to check that the procedure is correct. Then, execute the command again.
When none of the above items apply, collect the information required for troubleshooting as described in the following manual and contact a Fujitsu system engineer.
When using Express:
"Trouble analysis" in the ETERNUS SF Express Operation Guide
When using AdvancedCopy Manager:
"How to collect data" in the ETERNUS SF Operation Guide for Copy Control Module
