When using Web-Based Admin View for the first time, you need to initialize the management server on each node. Take the following steps in the order listed below.
Note
You do not have to initialize the server on the node on which PRIMECLUSTER was installed using the One Shot Installer tool
Operation Procedure:
Stop Web-Based Admin View on all the management servers and nodes.
# /etc/init.d/fjsvwvcnf stop # /etc/init.d/fjsvwvbs stop |
Set the IP addresses of the primary management server and secondary management server.
Execute the following command on all the management servers and nodes, referring to the example.
# /etc/opt/FJSVwvbs/etc/bin/wvSetparam primary-server <primary-management-server-IP-address> |
Example: Set the "primary management server IP" and "secondary management server IP" of the "operation management mode" found on the Cluster Configuration Worksheet.
# /etc/opt/FJSVwvbs/etc/bin/wvSetparam primary-server 10.34.214.181 # /etc/opt/FJSVwvbs/etc/bin/wvSetparam secondary-server 10.34.214.182 |
Restart Web-Based Admin View on all the management servers and nodes.
# /etc/opt/FJSVwvbs/etc/bin/wvCntl restart # /etc/init.d/fjsvwvcnf start |
See
Web-Based Admin View has some different operation management modes. For further details, see "1.2.2 System topology" and "Chapter 7 Web-Based Admin View setup modification" in the "PRIMECLUSTER Web-Based Admin View Operation Guide."
This section describes the procedure for confirming whether Web-Based Admin View has been started.
Confirmation Procedure
Check that all node information is output by executing the "wvstat(1M)" command on the connected management server.
Example:
In a two-node configuration consisting of node1(10.20.30.40) and node2(10.20.30.41), node1 is the primary management server and node2 is the secondary management server.
# /etc/opt/FJSVwvbs/etc/bin/wvstat
primaryServer 10.20.30.40 node1 http=10.20.30.40 Run 1d+7h36m primaryServer Sessions: 0 primaryServer Nodes: 2 10.20.30.40 node1 SunOS-5.8 1d+7h36m 10.20.30.41 node2 SunOS-5.8 1d+7h36m secondaryServer 10.20.30.41 node2 http=10.20.30.41 Run 1d+7h36m secondaryServer Sessions: 0 secondaryServer Nodes: 2 10.20.30.41 node2 SunOS-5.8 1d+7h36m 10.20.30.40 node1 SunOS-5.8 1d+7h36m #
If the information is not properly displayed, Web-Based Admin View has not been started or there may be an error in the Web-Based Admin View settings. Restart Web-Based Admin View and execute the operation again. If node information is still not displayed, refer to the "PRIMECLUSTER Web-Based Admin View Operation Guide" and check the parameter settings.
For details on the wvstat(1M) command, see the manual page.
The language environment in which Web-Based Admin View operates is set to English as default. Even though the client has a Japanese environment, the text of cluster resource management facility messages that are sent from the cluster node is displayed in English.
If you want to display the messages in Japanese, take the following steps to set up environment variables of Web-Based Admin View. You need to set up the variables using a system administrator access privilege on all nodes and the cluster management servers that construct a cluster system.
This operation must be executed with the system administrator authority for all cluster nodes and the cluster management server that make up the cluster system.
Attribute | Variable | Possible values | Meaning |
|---|---|---|---|
sys | Lang | C, ja | Language environment in which Web-Based Admin View operates. C: Operates in English. ja: Operates in Japanese. If this variable is not set, Web-Based Admin View operates in the English environment. |
Operation Procedure:
Stop Web-Based Admin View on all the management servers and nodes.
# /etc/init.d/fjsvwvcnf stop # /etc/init.d/fjsvwvbs stop |
Add the environment variable to the definition file (/etc/opt/FJSVwvbs/etc/webview.cnf) of Web-Based Admin View, and set the language.
Execute the following command on all the management servers and nodes, referring to the example.
# /etc/opt/FJSVwvbs/etc/bin/wvSetparam -add <attribute> <environment-variable> <set-value> |
Example: Add the environment variable and set the operation language to Japanese.
# /etc/opt/FJSVwvbs/etc/bin/wvSetparam -add sys lang ja |
Restart Web-Based Admin View on all the management servers and nodes.
# /etc/opt/FJSVwvbs/etc/bin/wvCntl restart # /etc/init.d/fjsvwvcnf start |
Note
For Web-Based Admin View to display messages in Japanese, the language environment of the personal computers and Solaris workstations that are being used as clients must be set to Japanese. If a client has an English environment, the message contents turn into garbled characters by the above setting change.
To change the environment variable again after it is added by the above procedure, execute the following command:
# /etc/opt/FJSVwvbs/etc/bin/wvSetparam lang <setting_value>For details on the command, see "4.5.3 Environment variable modification" in the "PRIMECLUSTER Web-Based Admin View Operation Guide."