The following information can be managed: Performance monitoring can be set at different intervals, refer to "7.2.3 Setting monitoring intervals" for the settings available for each device.
On the following tables, "A" indicates "Available", "N/A" indicates "Not Available".
Fibre Channel switch
Performance information (Unit) | Fibre Channel switch | |
|---|---|---|
Port | Transfer rates of send/receive data (MB/S) | A |
Number of CRC errors | A |
ETERNUS Disk storage system
Performance information | ETERNUS DX400/DX400 S2 series, | ETERNUS2000 | ETERNUS DX60/DX60 S2,DX80/DX80 S2,DX90/DX90 S2 | |
|---|---|---|---|---|
Logical Volume | Read/Write count | A | A | A |
Read/Write data transfer rate | A | A | A | |
Read/Write response time | A | A | A | |
Read/Pre-fetch/Write cache hit rate | A | A | A | |
Disk drive | Disk busy rate | A | A | A |
CM | Load (CPU usage) rate | A | A | A |
Copy remaining amount | A | A | A | |
CA | Read/Write count | A | N/A | N/A |
Read/Write data transfer rate | A | N/A | N/A | |
CM Port | Read/Write count | N/A | A | A |
Read/Write data transfer rate | N/A | A | A | |
Device | Number of active disks | A | A | A |
Power consumption (W) | A | N/A | A | |
Temperature(C) | A | N/A | A |
Note
Do not simultaneously perform performance monitoring to a single device from multiple Management Server (administrative servers). The administrative server for Softek Storage Cruiser, the Management Server for ETERNUS SF Storage Cruiser, and the administrative server for Systemwalker Resource Coordinator are to be used for the performance monitoring.
In order to prevent a discrepancy with the times shown on the performance graph due to a discrepancy in the internal clocks for the Management Server and the monitored device, it is recommended that you enable the NTP setting to the Management Server and the monitored device to synchronize the internal clocks.
It is possible to reference performance information for the ETERNUS SF Storage Cruiser. However, there is some performance information which is not supported. For details, refer to the manual for System Service Quality Coordinator. Note that the ETERNUS SN200 MDS series fibre channel switch device is not supported.
If the monitored device has been restarted while performance monitoring was in progress, you may be unable to acquire accurate performance data immediately after the restarting of the device. It is recommended that you first halt performance monitoring before performing any tasks which entail restarting the monitored device.
LogicalVolume(LUN) and RAIDGroup performance information including LogicalVolume, created by LUN Concatenation in the ETERNUS4000 and ETERNUS8000 that firmware versions are before V11L40, will not be displayed.
Performance information about the ETERNUS Disk storage system main frame volume and MVV/SDV are not supported, and performance information values for RAIDGroup cannot be guaranteed.
Performance monitoring cannot be done for the ETERNUS Disk storage system which do not have LogicalVolume (LUN).
The CA/CM Port performance information for the ETERNUS Disk storage system device displays the following information.
Device | Host interface | |||||||
|---|---|---|---|---|---|---|---|---|
FC | iSCSI | FCoE | SAS | |||||
CA | RA | CA/RA | CA | RA | CA/RA | |||
ETERNUS8000 models 700,900,1100,2100 | A | A(*1) | N/A | N/A | N/A | N/A | N/A | N/A |
ETERNUS DX8000 series | A | A(*1) | N/A | A | A (*1) | N/A | N/A | N/A |
ETERNUS DX90 | A | A(*1) | N/A | N/A | N/A | N/A | N/A | N/A |
ETERNUS DX80 | A | N/A | N/A | A | N/A | N/A | N/A | N/A |
ETERNUS DX80 S2 | A | A (*1) | A (*2) | A | N/A | A (*2) | A | N/A |
ETERNUS DX8000 S2 series | A | A (*1) | A (*2) | A | A (*1) | A (*2) | A | N/A |
(*1) Performance information during the execution of REC or ROPC is displayed as follows:
It is displayed as Read performance information, if the port is set on the Initiator.
It is displayed as Write performance information, if the port is set on the Target.
(*2) Performance information during the execution of REC includes the following information.
Read performance information includes the performance information during the execution of REC, if the port is set on the Initiator.
Write performance information includes the performance information during the execution of REC, if the port is set on the Target.
Performance information for VE ports used by 10 GbE(XGE) ports is not supported, and the values in the displayed performance information are not guaranteed. It is recommended that 0 be set for the transfer rate for VE ports used by 10 GbE(XGE) ports, and that performance and threshold values should not be monitored. For details on how to set this value, refer to "A.10 Explanation of the Configuration Settings File".
The CPU and ROE usage rates are displayed for the CM load (CPU usage) for ETERNUS DX400/DX400 S2 series, ETERNUS DX8000/DX8000 S2 series, ETERNUS4000 models 400 and 600 and ETERNUS8000 models 800, 1200 and 2200. For other ETERNUS Disk storage systems, the ROE usage rate is not displayed. Also, for ETERNUS Disk storage systems that do not have a ROE, the parity generation processing for RAID5 and RAID6 and encryption processing that would otherwise be performed by the ROE are performed by the CM and the CM-CPU.
RDB performance information cannot be displayed in environments that use the REC Disk Buffered Consistency function.
