The cluster setup of the primary node has been completed. Next, create the cluster environment of the secondary node.
Explanation
The cluster setup of the primary node has been completed.
System action
The system ends processing normally.
System administrator response
In accordance with the procedure for creating a cluster environment, perform the next step.
The cluster setup of the secondary node has been completed.
Explanation
The cluster setup of the secondary node has been completed.
System action
The system ends processing normally.
System administrator response
In accordance with the procedure for creating a cluster environment, perform the next step.
The cluster deletion of the primary node has been completed.
Explanation
The cluster deletion of the primary node has been completed.
System action
The system ends processing normally.
System administrator response
In accordance with the procedure for deleting a cluster environment, perform the next step.
The cluster deletion of the secondary node has been completed. Next, delete the cluster environment of the primary node.
Explanation
The cluster deletion of the secondary node has been completed.
System action
The system ends processing normally.
System administrator response
In accordance with the procedure for deleting a cluster environment, perform the next step.
The cluster setup command or cluster unsetup command is already running.
Explanation
The cluster setup command or cluster unsetup command is already running.
System action
The system terminates processing.
System administrator response
Verify that no other cluster setup command or cluster deletion command is running.
Failed to acquire information from the cluster file. Error Code = [CODE], File Name = [FILE]
Explanation
It failed to acquire information from the cluster file.
Parameters
CODE : Error code
FILE : Cluster file name
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
No cluster environment setting file exists. File Name = [FILE]
Explanation
No cluster environment setting file exists.
Parameters
FILE : Cluster environment setting file name
System action
The system terminates processing.
System administrator response
[Solaris, Linux, HP-UX, and AIX versions]
Verify that a correct mount point name is used for the shared disk.
Check the mount status of the shared disk.
[Windows version]
Contact a Fujitsu systems engineer.
The cluster setup has been completed.
Explanation
The cluster setup has been completed.
System action
The system terminates processing.
System administrator response
Verify that the AdvancedCopy Manager logical node name or job name (service name) is not duplicated.
Verify that an AdvancedCopy Manager shared disk used in another cluster is not mounted.
Failed to acquire information from the registry information file. Error Code = [CODE], File Name = [FILE]
Explanation
Failed to acquire information from the registry information file.
Parameters
CODE : Error code
FILE : Registry information file name
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
The processing was canceled.
Explanation
The processing was canceled.
System action
The system terminates processing.
System administrator response
No response is required.
A cluster system environment has been created in [CLUSTER].
Explanation
A cluster system environment was already created in another cluster system.
Parameters
CLUSTER : Name of cluster system that has been created. The displayed strings and explanation are as follows.
Displayed strings | Name of cluster system |
|---|---|
SAFE | SynfinityCluster or PRIMECLUSTER |
MSCS | MSCS or WSFC |
MCSG | MC/ServiceGuard |
VCS | VERITAS Cluster Server |
PRM | PRIMECLUSTER |
HACM | High Availability Cluster Multi-Processing |
System action
The system terminates processing.
System administrator response
Use the cluster setup command supported by the current OS to create a cluster environment.
The number of nodes that can be registered is exceeded. Maximum Number of Nodes=[NUMBER]
Explanation
The number of nodes that can be registered is exceeded.
Parameters
NUMBER : Maximum number of cluster environments that can be registered
System action
The system terminates processing.
System administrator response
Unsetup other cluster environments and re-execute processing.
If no other cluster environments can be modified, contact a Fujitsu systems engineer.
The cluster setup tool does not support this version of AdvancedCopy Manager.
Explanation
The cluster setup tool does not support this version of AdvancedCopy Manager.
System action
The system terminates processing.
System administrator response
Check the version of AdvancedCopy Manager.
Failed to create a cluster environment on a shared disk. Error Code=[CODE1]-[CODE2]
Explanation
It failed to create a cluster environment on a shared disk.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
System action
The system terminates processing.
System administrator response
Verify that the shared disk can be used on the execution node.
The cluster environment creation command terminated with an error. Error Code = [CODE1]-[CODE2], Package Name = [NAME]
Explanation
The cluster environment creation command terminated with an error.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
NAME : Package name of the command that terminated with an error
System action
The system terminates processing.
System administrator response
Set up the environment for the package that terminated with an error in accordance with the relevant instructions.
For information on instruction for the package, refer to the following:
[Solaris, Linux, HP-UX, and AIX versions]
Other : Message/s output immediately to this message being output
[Windows version]
FJSVswstf : "Work directory"\var\clset\clset_FJSVswstf.log
FJSVswsts : "Work directory"\var\clset\clset_FJSVswsts.log
FJSVswsrp : "Work directory"\var\clset\clset_FJSVswsrp.log
FJSVswssc : "Work directory"\var\clset\clset_FJSVswssc.log
PortServ : A message box that was output before this message was output
DBSetUp : Contact a Fujitsu systems engineer.
Failed to read the command definition file for creating a cluster environment.
Explanation
It failed to read the command definition file for creating a cluster environment.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to set up information in the cluster file. Error Code = [CODE], File Name = [FILE]
Explanation
Failed to set up information in the cluster file.
Parameters
CODE : Error code
FILE : Cluster file name
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
The service name is already used in another cluster environment [NODE].
Explanation
The service name (job name) was already being used in another cluster environment.
Parameters
NODE : Name of AdvancedCopy Manager logical node that uses the service name (job name)
System action
The system terminates processing.
System administrator response
Check the service name
Failed to create a registry information file. Error Code = [CODE1]-[CODE2]
Explanation
Failed to create a registry information file.
Parameters
CODE1 : Error code
CODE2 : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
The node name is in an invalid format.
Explanation
The node name is in an invalid format.
System action
The system terminates processing.
System administrator response
Check the AdvancedCopy Manager logical node name.
The Storage Management Server has been constructed with another node name [NODE].
Explanation
The Storage Management Server has been set up in AdvancedCopy Manager with another logical node name.
Parameters
NODE : Name of AdvancedCopy Manager logical node constructed as a Storage Management Server service
System action
The system terminates processing.
System administrator response
Check the logical node name in the setup of the Storage Management Server service.
The primary node has an environment constructed with another cluster system [CLUSTER].
Explanation
The primary node has an environment set up for another cluster system.
Parameters
CLUSTER : Cluster system of the primary node
System action
The system terminates processing.
System administrator response
Configure an environment using the same command as that for the cluster system of the primary node.
The primary node has an environment constructed with another server type [TYPE].
Explanation
The primary node has an environment set up with another server type.
Parameters
TYPE : Server type of the primary node. The displayed strings and explanation are as follows.
Displayed strings | Explanation |
|---|---|
1 | Storage Management Server |
2 | Storage server |
System action
The system terminates processing.
System administrator response
Check the Storage server type.
The primary node has an environment constructed with another language [LANG].
Explanation
The primary node has an environment set up with another language.
Parameters
LANG : Language type of the primary node. The displayed strings and explanation are as follows.
Displayed strings | Explanation |
|---|---|
JAPANESE | Japanese version |
ENGLISH | English version |
System action
The system terminates processing.
System administrator response
Check the AdvancedCopy Manager language type.
The primary node has an environment constructed with another code [CODE].
Explanation
The primary node has an environment set up with another code.
Parameters
CODE : Code of the primary node
System action
The system terminates processing.
System administrator response
Check the AdvancedCopy Manager code.
The primary node does not have a cluster environment.
Explanation
The primary node does not have a cluster environment.
System action
The system terminates processing.
System administrator response
Configure a cluster environment for the primary node.
Verify that the mount point or disk resource is correct.
The primary node has an environment constructed with another version [VERSION].
Explanation
The primary node has an environment set up with another version.
Parameters
VERSION : Version of the primary node
System action
The system terminates processing.
System administrator response
Check the AdvancedCopy Manager version.
The primary node has an environment constructed with another AFS type [TYPE].
Explanation
The primary node has an environment set up with another AFS type.
Parameters
TYPE : AFS type. The displayed strings and explanation are as follows.
Displayed strings | Explanation |
|---|---|
1 | Non-AFS |
2 | AFS |
System action
The system terminates processing.
System administrator response
Check the AdvancedCopy Manager AFS type.
No cluster environment has been created.
Explanation
No cluster environment has been created.
System action
The system terminates processing.
System administrator response
Verify that an AdvancedCopy Manager cluster environment was created.
The command for unsetup the cluster environment terminated with an error. Error Code = [CODE1]-[CODE2], Package Name = [NAME]
Explanation
The command for unsetup the cluster environment terminated with an error.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
NAME : Package name of the command that terminated with an error
System action
The system terminates processing.
System administrator response
Set up the environment for the package that terminated with an error in accordance with the relevant instructions.
For information on instructions for the package, refer to the following:
[Solaris, Linux, HP-UX, and AIX versions]
Other: Message/s output immediately to this message being output
[Windows version]
FJSVswstf : "Work directory"\var\clset\clset_FJSVswstf.log
FJSVswsts : "Work directory"\var\clset\clset_FJSVswsts.log
FJSVswsrp : "Work directory"\var\clset\clset_FJSVswsrp.log
FJSVswssc : "Work directory"\var\clset\clset_FJSVswssc.log
PortServ : A message box that was output before this message was output
DBSetUp : Contact a Fujitsu systems engineer.
The cluster environment of the secondary node has not been deleted.
Explanation
The cluster environment of the secondary node has not been deleted.
System action
The system terminates processing.
System administrator response
After deleting the cluster environment of the secondary node, re-execute processing.
Execute processing after deleting the cluster environment of all secondary nodes in cluster operation.
Failed to clear the cluster file. Error Code = [CODE], File Name = [PATH]
Explanation
It failed to clear the cluster file.
Parameters
CODE : Error code
PATH : Cluster file path
System action
The system continues processing.
System administrator response
Although the cluster environment was deleted, refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to delete the cluster file. Error Code = [CODE1]-[CODE2], File Name = [PATH]
Explanation
It failed to delete the cluster file.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
PATH : Cluster file path
System action
The system continues processing.
System administrator response
Although the cluster environment was deleted, refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Deletion of the cluster in forced mode has been completed.
Explanation
Deletion of the cluster in forced mode has been completed.
System action
The system ends processing.
System administrator response
In accordance with the procedure for deleting a cluster environment, perform the next step.
No cluster environment with the node name (NAME) has been created.
Explanation
No cluster environment with the specified node name has been created.
Parameters
NAME : Specified AdvancedCopy Manager logical node name
System action
The system terminates processing.
System administrator response
Check the AdvancedCopy Manager logical node name.
The node was not deleted.
Explanation
The node was not deleted.
System action
The system terminates processing.
System administrator response
After deleting the node, re-execute processing.
The cluster file does not exist. File Name = [PATH]
Explanation
The cluster file does not exist.
Parameters
PATH : Cluster file pathname
System action
The system terminates processing.
System administrator response
[Solaris, Linux, HP-UX, and AIX versions]
Check the mount status of the shared disk.
[Windows version]
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to restore the registry information file. Error Code = [CODE]
Explanation
It failed to restore the registry information file.
Parameters
CODE : Error code
System action
The system continues processing.
System administrator response
Although the cluster environment was deleted, refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
The secondary node has a cluster environment.
Explanation
The secondary node has a cluster environment.
System action
The system terminates processing.
System administrator response
Verify that the mount point or disk resource is correct.
The primary node has a cluster environment constructed with the logical node [NODE].
Explanation
The primary node has a cluster environment set up with the logical node.
Parameters
NODE : AdvancedCopy Manager logical node name
System action
The system terminates processing.
System administrator response
Verify that the mount point or disk resource or shared disk is correct.
The cluster deletion of the secondary node has been completed. Next, delete the cluster environment of another secondary node.
Explanation
The cluster deletion of the secondary node has been completed. Next, delete the cluster environment of another secondary node.
System action
The system ends processing.
System administrator response
In accordance with the procedure for deleting a cluster environment, perform the next step.
An internal inconsistency occurred.
Explanation
An internal conflict occurred.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
[VALUE1] or [VALUE2] must be specified in [OPT].
Explanation
The value indicated in VALUE1 or VALUE2 parameter must be specified with the option indicated in OPT.
Parameters
OPT : Option
VALUE1 : Specifiable value 1
VALUE2 : Specifiable value 2
System action
The system terminates processing.
System administrator response
Re-execute processing using correct values.
[VALUE] must be specified in [OPT].
Explanation
The value indicated in VALUE parameter must be specified with the option indicated in OPT.
Parameters
OPT : Option
VALUE : Specifiable value
System action
The system terminates processing.
System administrator response
Re-execute processing using correct values.
Failed to start the command. Error Code = [CODE1]-[CODE2], Command Name = [COMMAND]
Explanation
It failed to start the command.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
COMMAND : Command name
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
The command was started by someone else than the root user.
Explanation
The command was started by someone else than the root user.
System action
The system terminates processing.
System administrator response
The root user must execute the command.
The -f option cannot be specified on the Storage server.
Explanation
The -f option cannot be specified on the Storage server.
System action
The system terminates processing.
System administrator response
If the installed Storage server type is Manager, verify that the Storage Management Server service has not already been set up.
Re-execute the command without the -f option.
The IP address was in an invalid format.
Explanation
The IP address was in an invalid format.
System action
The system terminates processing.
System administrator response
Check the IP address.
A reserved word was specified as the node name.
Explanation
A reserved word was specified as the node name.
System action
The system terminates processing.
System administrator response
Check the AdvancedCopy Manager logical node name.
Data different from the previous time was specified. Option = [OPT], Data = [DATA]
Explanation
Data different from the previous time was specified.
Parameters
OPT : Option
DATA : Data previously specified
System action
The system terminates processing.
System administrator response
Check the option value.
Do not mount the shared disk.
Explanation
Do not mount the shared disk.
System action
The system terminates processing.
System administrator response
Check the mount state of the shared disk for AdvancedCopy Manager share data.
When the server is the Storage Management Server transactions, also check the mount state of DB file system.
Failed to start the mount check command.
Explanation
It failed to start the mount check command.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
An error occurs though the cluster environment of AdvancedCopy Manager was removed. Carry out treatment corresponding to the message being output.
Explanation
An error occurs though the cluster environment of AdvancedCopy Manager was removed. Carry out treatment corresponding to the message being output.
System action
The system ends processing.
System administrator response
Comply with [System administrator response] of message that is output before this message.
The shared disk for another service is mounted. node=[NODE].
Explanation
The shared disk for another service is mounted.
Parameters
NODE : Logical node name for the shared disk which is being mounted
System action
The system terminates processing.
System administrator response
Check whether the mounted shared disk is also object transactions.
The subnet was in an invalid format.
Explanation
The subnet was in an invalid format.
System action
The system terminates processing.
System administrator response
Check the format of the subnet.
Failed in the acquisition of the device information.
Explanation
It failed in the acquisition of the device information.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
A device is different. The last device=[DEVICE1], This device=[DEVICE2]
Explanation
The device has changed.
Parameters
DEVICE1 : Device mounted to the mount point of the shared disk for AdvancedCopy Manager share data when a command was executed last time
DEVICE2 : Device mounted to the mount point of the shared disk for current AdvancedCopy Manager share data
System action
The system terminates processing.
System administrator response
Mount the last time used device and re-execute processing.
The service is not offline.
Explanation
The service is not offline.
System action
The system terminates processing.
System administrator response
Stops the transactions and re-execute a command.
AdvancedCopy Manager has not been installed.
Explanation
AdvancedCopy Manager has not been installed.
System action
The system terminates processing.
System administrator response
Verify that AdvancedCopy Manager has been correctly installed.
The IP address or subnet mask was incorrect.
Explanation
The IP address or subnet mask was incorrect.
System action
The system terminates processing.
System administrator response
Check the IP address or subnet mask.
Failed to connect to the service control manager. Error Code = [CODE]
Explanation
It failed to connect to the service control manager.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to open the service. Service Name: [SERVICE], Error Code = [CODE]
Explanation
It failed to open the service.
Parameters
SERVICE : Service name
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to acquire the service status. Service Name: [SERVICE], Error Code = [CODE]
Explanation
It failed to acquire the service status.
Parameters
SERVICE : Service name
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to wait for a thread. Error Code = [CODE]
Explanation
It failed to wait for a thread.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to stop the service. Service Name: [SERVICE], Error Code = [CODE]
Explanation
It failed to stop the service.
Parameters
SERVICE : Service name
CODE : Error code
System action
The system terminates processing.
System administrator response
Manually stop the service.
Failed to stop the service (timeout). Service Name: [SERVICE]
Explanation
It failed to stop the service due to a timeout.
Parameters
SERVICE : Service name
System action
The system terminates processing.
System administrator response
Manually stop the service.
The program will not be correctly installed if you cancel the setup now. Do you want to cancel the setup?
Explanation
The program will not be correctly installed if you cancel the setup now. Do you want to cancel the setup?
System action
The system terminates processing if "Yes" is clicked.
System administrator response
Select "Yes" to cancel setup.
Select "No" to continue setup.
No parameter was entered.
Explanation
No parameter was entered.
System action
The system terminates processing.
System administrator response
Enter parameters that were not entered.
The free space was not sufficient for the setup.
Explanation
The free space was not sufficient for the setup.
System action
The system terminates processing.
System administrator response
Secure necessary free space.
Verify that you have the ownership for the selected disk.
Check the status of the selected disk.
An invalid subnet mask was used.
Explanation
An invalid subnet mask was used.
System action
The system terminates processing.
System administrator response
Check the IP address or subnet mask.
Failed to create a directory. Directory = [PATH]
Explanation
It failed to create a directory.
Parameters
PATH : Directory path
System action
The system terminates processing.
System administrator response
After creating a directory, re-execute processing.
Failed to set up registry information.
Explanation
It failed to set up registry information.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide (for Windows)"
The cluster environment will not be released if you cancel the unsetup now. Do you want to cancel the unsetup?
Explanation
The cluster environment will not be released if you cancel the unsetup now. Do you want to cancel the unsetup?
System action
The system terminates processing if "Yes" is clicked.
System administrator response
Select "Yes" to cancel unsetup.
Select "No" to continue unsetup.
No logical node name was selected.
Explanation
No logical node name was selected.
System action
The system terminates processing.
System administrator response
Select a logical node name.
Failed to create a thread. Error Code = [CODE]
Explanation
It failed to create a thread.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Are you sure the cluster environment may be forcibly released?
Explanation
Are you sure the cluster environment may be forcibly released?
System action
The cluster environment is forcibly released if "Yes" is clicked.
System administrator response
Select "Yes" to continue forcibly unsetup.
Select "No" to cancel forcibly unsetup.
Failed to fetch computer name. Error Code = [CODE]
Explanation
It failed to fetch the computer name.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Usage: stgclset_safe -k NodeType -m MountPoint [-n NodeName -s Service] [-i IPAddress -f mgr] [-r cmd]
Explanation
An invalid option was specified.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
For the primary node, specify an IP address, node name, and service name.
Explanation
For the primary node, specify an IP address, node name, and service name (job name).
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
For the secondary node, no node type, or mount point can be specified.
Explanation
For the secondary node, no node type, or mount point can be specified.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
Failed to register the status transition procedure. Error Code = [CODE1]-[CODE2]
Explanation
It failed to register the status transition procedure.
Parameters
CODE1 : Error code1
CODE2 : Error code2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
SynfinityCluster or PRIMECLUSTER has not been installed.
Explanation
SynfinityCluster or PRIMECLUSTER has not been installed.
System action
The system terminates processing.
System administrator response
Check the SynfinityCluster or PRIMECLUSTER environment.
Usage: stgclunset_safe -n NodeName [-f]
Explanation
An invalid option was specified.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
Failed to delete the status transition procedure. Error Code = [CODE1]-[CODE2]
Explanation
it failed to delete the status transition procedure.
Parameters
CODE1 : Error code1
CODE2 : Error code2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
For the Storage Management Server transaction, specify an IP Address.
Explanation
For the Storage Management Server transaction, specify an IP Address.
System action
The system terminates processing.
System administrator response
Re-execute after checking the IP address.
For the Storage server transaction, no IP Address can be specified.
Explanation
For the Storage server transaction, no IP Address can be specified.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, then re-execute.
Failed to delete the CmdLine resource. Error Code=[CODE1]-[ CODE2]
Explanation
It failed to delete the command line resource.
Parameters
CODE1 : Error code1
CODE2 : Error code2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
It failed in the registration of the CmdLine resource. Error Code=[CODE1]-[CODE2]
Explanation
Failed to register the command line resource.
Parameters
CODE1 : Error code1
CODE2 : Error code2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Usage : stgclset_sun -k NodeType -m MountPoint [-h NetworkResource -n NodeName -s Service] [-i IPAddress -f mgr]
Explanation
An incorrect option has been specified.
System action
The system terminates processing.
System administrator response
Check the command, then re-execute.
For the primary node, specify a network resource, node name, and service name.
Explanation
Specify the network resource name, the node name, and the transaction name at the primary node.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, then re-execute.
For the secondary node, it can not be specified except for node type and mount point.
Explanation
Only node type and mount point can be specified at the secondary node.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, then re-execute.
For the Storage management server transaction, specify an IP address.
Explanation
Specify the IP address for the Storage Management Server transaction.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, then re-execute.
For the Storage server transaction, no IP address can be specified.
Explanation
An IP address cannot be specified for Storage server transactions.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, then re-execute.
Sun Cluster has not been installed.
Explanation
Sun Cluster is not installed.
System action
The system terminates processing.
System administrator response
Check the Sun Cluster environment.
The network resource is already used in another cluster environment [NODE].
Explanation
The network resource is already being used by another cluster environment.
Parameters
NODE : Storage MGR logical node name that is using the network resource
System action
The system terminates processing.
System administrator response
Ensure the network resource as specified is the correct one.
Failed to add AdvancedCopy Manager resource.
Explanation
AdvancedCopy Manager resource registration failed.
System action
The system terminates processing.
System administrator response
The "scrgadm" command executed using the cluster configuration commands is displayed on the screen. Fix the "scrgadm" command problem, and then re-execute the cluster configuration command.
Failed to execute the AdvancedCopy Manager resource add command.
Explanation
The AdvancedCopy Manager resource registration command failed to start.
System action
The system terminates processing.
System administrator response
Contact your Fujitsu systems engineer.
Failed to delete the AdvancedCopy Manager resource.
Explanation
The AdvancedCopy Manager application resource deletion failed.
System action
The system terminates processing.
System administrator response
Manually delete the AdvancedCopy Manager application resource for the relevant transaction.
The application resource name is "STGMGR-APP-logical_node_name".
Failed to delete the AdvancedCopy Manager resource type.
Explanation
The AdvancedCopy Manager resource type deletion failed.
System action
The system terminates processing.
System administrator response
Manually delete the AdvancedCopy Manager resource type.
The AdvancedCopy Manager resource type name is "FJSV.S-MGR".
Failed to confirm the resource group. code=[CODE]. group=[GROUP]
Explanation
Confirmation of the resource group failed.
Parameters
CODE : Internal code
GROUP : Resource group name
System action
The system terminates processing.
System administrator response
If the internal code is 0, check that "RG MODE=Failover" is set for the transaction (resource group).
If the internal code is a value other than 0, contact your Fujitsu systems engineer.
Usage: stgclunset_sun -n NodeName [-f]
Explanation
An incorrect option is specified.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, then re-execute.
A parameter was specified.
Explanation
A parameter was specified.
System action
The system terminates processing.
System administrator response
Execute the command without specifying a parameter.
Cluster Service was not started.
Explanation
Cluster Service was not started.
System action
The system terminates processing.
System administrator response
Check the MSCS or cluster service environment.
MSCS has not been installed.
Explanation
MSCS or WSFC has not been installed.
System action
The system terminates processing.
System administrator response
Check the MSCS or cluster service environment. Verify the following:
whether MSCS or WSFC is installed
whether setup of MSCS or WSFC is completed
Failed to acquire the drive name from the physical disk resource.
Explanation
It failed to acquire the drive name from the physical disk resource.
System action
The system terminates processing.
System administrator response
Check the MSCS or cluster service environment.
The usage of the IP address was not specified.
Explanation
The usage of the IP address was not specified.
System action
The system terminates processing.
System administrator response
Specify the IP address.
Failed to acquire the quorum disk name. Error Code = [CODE]
Explanation
It failed to acquire the quorum disk name.
System action
CODE : Error code
System action
The system terminates processing.
System administrator response
Verify that the quorum disk is operating normally.
Failed to acquire the quorum disk information.
Explanation
It failed to acquire the quorum disk information.
System action
The system terminates processing.
System administrator response
Acquire the ownership of the quorum disk.
Failed to acquire the quorum disk information. Error Code = [CODE]
Explanation
It failed to acquire the quorum disk information.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Verify that the quorum disk is operating normally.
Failed to acquire the primary node name. Error Code = [CODE]
Explanation
It failed to acquire the primary node name.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to check the cluster group. Error Code = [CODE]
Explanation
It failed to check the cluster group.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to create a cluster group. Error Code = [CODE]
Explanation
It failed to create a cluster group.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to set up the property information of the cluster group. Error Code = [CODE]
Explanation
It failed to set up the property information of the cluster group.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Verify that the cluster name is correct.
Check whether group [GROUP] exists. Error Code = [CODE]
Explanation
Check whether the group exists.
Parameters
GROUP : Cluster group name
CODE : Error code
System action
The system terminates processing.
System administrator response
Verify that the group exists.
Failed to create a cluster resource. Error Code = [CODE]
Explanation
It failed to create a cluster resource.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to set up the property information of the cluster resource. Error Code = [CODE]
Explanation
It failed to set up the property information of the cluster resource.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Check the followings.
Whether the cluster name is correct.
Whether the network name for external connection is correct.
Whether the network name and IP address overlap others.
Failed to add a cluster dependence relationship. Error Code = [CODE]
Explanation
It failed to add a cluster dependence relationship.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to copy [REG] registry. Resource Name = [RESOUCE]
Explanation
It failed to replicate the registry.
Parameters
REG : Registry
RESOUCE : Resource name
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to set up the priority ownership. Error Code = [CODE]
Explanation
It failed to set up the priority ownership.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
A check is performed as to whether the cluster group specified by the service name (job name) in the cluster administrator (MSCS) or Failover Cluster Manager (WSFC) exists.
When the cluster group exists, the property is checked for priority ownership.
When priority ownership has been set up, the cluster configuration command is executed again.
When there is no cluster group, the cluster group of a service name (job name) is created and a cluster configuration command is executed again.
When priority ownership is not set up, priority ownership is set up and a cluster configuration command is executed again.
Failed to acquire the local node name. Error Code = [CODE]
Explanation
It failed to acquire the local node name.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Acquire the ownership of [GROUP] group.
Explanation
Acquire the ownership of the group.
Parameters
GROUP : Cluster group name
System action
The system terminates processing.
System administrator response
Acquire the ownership of the cluster group.
Failed to check the ownership of the group. Error Code = [CODE]
Explanation
It failed to check the ownership of the group.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to place [RESOURCE] offline. Error Code = [CODE1]-[CODE2]
Explanation
It failed to place the resource offline.
Parameters
RESOURCE : Resource name
CODE1 : Error code 1
CODE2 : Error code 2
System action
The system terminates processing.
System administrator response
After manually placing the resource offline, re-execute processing.
Failed to delete the resource. Resource Name = [RESOURCE], Error Code = [CODE]
Explanation
It failed to delete the resource.
Parameters
RESOURCE : Resource name
CODE : Error code
System action
The system continues processing.
System administrator response
Manually delete the resource.
Failed to move the group. Error Code = [CODE]
Explanation
Failed to move the group.
Parameters
CODE : Error code
System action
The system continues processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to find the cluster file. File Name = [FILE]
Explanation
Failed to find the cluster file.
Parameters
FILE : Cluster file name
System action
The system terminates processing.
System administrator response
Verify that the shared disk is online.
Usage : stgclset_mcsg -k NodeType -m MountPoint [-n NodeName -s Service -v VolumeGroup -i IPAddress -u Subnet]
Explanation
The syntax is incorrect or an invalid option has been specified.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
For the primary node, specify all options.
Explanation
For the primary node, specify all options.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
For the secondary node, no node name or mount point can be specified.
Explanation
For the secondary node, no node name or mount point can be specified.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
Usage : stgclunset_mcsg -n NodeName [-f]
Explanation
The syntax is incorrect or an invalid option has been specified.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
Failed in the preparation of the AdvancedCopy Manager start/stop command for the package.
Explanation
It failed in the preparation of the AdvancedCopy Manager start/stop command for the package.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed in the deletion of the AdvancedCopy Manager start/stop command for the package.
Explanation
It failed in the deletion of the AdvancedCopy Manager start/stop command for the package.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed in the preparation of the sample control script for the package.
Explanation
It failed in the preparation of the sample control script for the package.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Usage : stgclset_vcs -k NodeType -m MountPoint [ -n NodeName -s Service] [-i IPAddress -f mgr]
Explanation
The syntax is incorrect or an invalid option has been specified.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
For the primary node, specify a node name, service name.
Explanation
For the primary node, specify a node name, service name.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
VERITAS Cluster Server has not been installed.
Explanation
VERITAS Cluster Server has not been installed.
System action
The system terminates processing.
System administrator response
Check the environment of VERITAS Cluster Server.
Usage: stgclunset_vcs -n NodeName [-f]
Explanation
The syntax is incorrect or an invalid option has been specified.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, then re-execute.
Failed to create the AdvancedCopy Manager application. Error Code = [CODE1]-[CODE2]
Explanation
It failed to make the AdvancedCopy Manager application.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
For the secondary node, it can not be specified except for node type and mount point.
Explanation
For the secondary node, it can not be specified except for node type and mount point.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
For the Storage Management Server transaction, specify an IP address.
Explanation
For the Storage Management Server transaction, specify an IP address.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
For the Storage server transaction, no IP address can be specified.
Explanation
For the Storage server transaction, no IP address can be specified.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
Failed to delete the AdvancedCopy Manager application. Error Code = [CODE1]-[CODE2]
Explanation
It failed to delete the AdvancedCopy Manager application.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Usage: stgclset_lxprm -k NodeType -m MountPoint [-n NodeName -s Service] [-i IPAddress -f mgr][-r cmd]
Explanation
An invalid option was specified.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
For the primary node, specify a node name and service name.
Explanation
For the primary node, specify a node name and service name.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
For the secondary node, it cannot be specified except for node type and mount point.
Explanation
For the secondary node, it cannot be specified except for node type and mount point.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
Failed to register the status transition procedure. Error Code = [CODE1]-[CODE2]
Explanation
It failed to register the status transition procedure.
Parameters
CODE1 : Error code1
CODE2 : Error code2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
PRIMECLUSTER has not been installed.
Explanation
PRIMECLUSTER has not been installed.
System action
The system terminates processing.
System administrator response
Check the PRIMECLUSTER environment.
Usage: stgclunset_lxprm -n NodeName [-f]
Explanation
An invalid option was specified.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
Failed to delete the status transition procedure. Error Code = [CODE1]-[CODE2]
Explanation
It failed to delete the status transition procedure.
Parameters
CODE1 : Error code1
CODE2 : Error code2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
For the Storage Management Server transaction, specify an IP address.
Explanation
For the Storage Management Server transaction, specify an IP Address.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
For the Storage server transaction, no IP address can be specified.
Explanation
For the Storage server transaction, no IP Address can be specified.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
Failed to delete the CmdLine resource. Error Code=[CODE1]-[CODE2]
Explanation
It failed to delete the command line resource.
Parameters
CODE1 : Error code1
CODE2 : Error code2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
It failed in the registration of the CmdLine resource. Error Code=[CODE1]-[CODE2]
Explanation
It failed to register the command line resource.
Parameters
CODE1 : Error code1
CODE2 : Error code2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
An internal inconsistency occurred.
Explanation
An internal inconsistency occurred.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
No port number was entered.
Explanation
No port number was entered.
System action
The system terminates processing.
System administrator response
Enter the port number and retry.
The same port number was entered.
Explanation
The same port number was entered.
System action
The system terminates processing.
System administrator response
Check the port number.
Check whether the port number is right. Please perform by the port number which is not used by others.
Port number specified in [SERVICE1] has already been specified.
Service that uses the port number=[SERVICE2]
Explanation
The port number which had already been registered was specified.
Parameters
SERVICE1 : Service name
SERVICE2 : Registered service name
System action
The system terminates processing.
System administrator response
Check the port number and retry.
An error occurred in searching port number information.
Explanation
An error occurred in searching port number information.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Port number specified in [SERVICE] has been set up with a different number.
Explanation
Port number specified has been set up with a different number.
Parameters
SERVICE : Service name
System action
The system terminates processing.
System administrator response
Check the port number.
When you change a port number, manually change the port number of the live operations communication service (stgxfws_logic node name) found in the "Windows installation directory"\system32\drivers\etc\services, and re-execute the task.
Failed to register service [SERVICE].
Explanation
It failed to register service.
Parameters
SERVICE : Service name
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to delete service [SERVICE].
Explanation
It failed to delete service.
Parameters
SERVICE : Service name
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to acquire an account of AdvancedCopy Manager.
Explanation
It failed to acquire an account of AdvancedCopy Manager.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to register to the port number management file. Error=[CODE]
Explanation
It failed to register to the port number management file.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to read the port number management file. Error=[CODE]
Explanation
It failed to read the port number management file.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to write the port number. Error=[CODE]
Explanation
It failed to write the port number.
Parameters
CODE : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Failed to acquire machine information.
Explanation
It failed to acquire machine information.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
An invalid password was entered.
Explanation
An invalid password was entered.
System action
The system terminates processing.
System administrator response
Check the password.
Failed to write the linefeed.
Explanation
It failed to write the linefeed.
System action
The system terminates processing.
System administrator response
Start a new line for the last of a "Windows installation directory"\system32\drivers\etc\services file manually, and then re-execute.
Failed to confirm the linefeed.
Explanation
It failed to confirm the linefeed.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
This command arguments are incorrect.
Explanation
The command arguments are incorrect.
System action
The system terminates processing.
System administrator response
Do not execute this command. Execute the cluster unsetup command to unsetup the cluster setting.
Failed to open the cluster environment setting file. Filename=[FILE]
Explanation
The cluster environment setting file (clsetup.ini) could not be opened.
Parameters
FILE : File name
System action
The system terminates processing.
System administrator response
Check for the presence of the file and the access permission, and re-execute the command.
Failed to read the cluster environment setting file. Filename=[FILE], Section=[SECTION], Key=[KEY]
Explanation
The cluster environment setting file (clsetup.ini) could not be read.
Parameters
FILE : File name
SECTION : Section name
KEY : Key name
System action
The system terminates processing.
System administrator response
Check the access permission and the accuracy of the file data, and re-execute the command.
Failed to open the registry. Registry=[REG], Key=[KEY], Error=[ERROR]
Explanation
The registry could not be opened.
Parameters
REG : Registry
KEY : Key name
ERROR : Error code
System action
The system terminates processing.
System administrator response
Recover registry information by using the OS standard function.
Failed to read the registry. Registry=[REG], Key=[KEY], Value=[VALUE], Error=[ERROR]
Explanation
The registry could not be read.
Parameters
REG : Registry
KEY : Key name
VALUE : Value name
ERROR : Error code
System action
The system terminates processing.
System administrator response
Recover registry information by using the OS standard function.
Failed to open the cluster setting definition file. Filename=[FILE]
Explanation
The cluster setting define file could not be opened.
Parameters
FILE : File name
System action
The system terminates processing.
System administrator response
Check for the presence of the cluster setting definition file indicated in FILE parameter and the access permission and re-execute the command.
Failed to read the cluster setting definition file. Filename=[FILE], Line=[LINE], Value=[VALUE]
Explanation
The cluster setting definition file could not be read.
Parameters
FILE : File name
LINE : Line number
VALUE : Data
System action
The system terminates processing.
System administrator response
The cluster setting definition file indicated in FILE parameter may be corrupt. Replace the cluster setting definition file with the file that was originally installed and then re-execute the command.
The directory does not exist. Directory=[DIR]
Explanation
The directory could not be found.
Parameters
DIR : Directory name
System action
The system terminates processing.
System administrator response
Check for the presence of the directory and the access permission, and then re-execute the command.
Failed to copy the directory. Source Directory=[SRCDIR], Target Directory=[DSTDIR]
Explanation
The directory could not be copied.
Parameters
SRCDIR : Source directory for copying
DSTDIR : Destination directory for copying
System action
The system terminates processing.
System administrator response
Check for the presence of the directory, the access permission, the free disk space, and then re-execute the command.
Failed to delete the directory. Directory=[DIR]
Explanation
The directory could not be deleted.
Parameters
DIR : Directory name
System action
The system terminates processing.
System administrator response
Check for the presence of the directory and the access permission, and then re-execute the command.
Failed to move the directory. Source Directory=[SRCDIR], Target Directory=[DSTDIR]
Explanation
The file could not be moved.
Parameters
SRCDIR : Source directory for moving
DSTDIR : Destination directory for moving
System action
The system terminates processing.
System administrator response
Check for the presence of the directory, the access permission, the free disk space, and then re-execute the command.
Failed to create a directory. Directory=[DIR]
Explanation
The directory could not be created.
Parameters
DIR : Directory name
System action
The system terminates processing.
System administrator response
Check the access permission and the free disk space, and then re-execute the command.
Failed to copy the file. Source Filename=[SRCFILE], Target Filename=[DSTFILE]
Explanation
The file could not be copied.
Parameters
SRCFILE : Source file for copying
DSTFILE : Destination file for copying
System action
The system terminates processing.
System administrator response
Check for the presence of the file and the access permission, and then re-execute the command.
Failed to delete the file. Filename=[FILE]
Explanation
The file could not be deleted.
Parameters
FILE : File name
System action
The system terminates processing.
System administrator response
Check for the presence of the file and the access permission, and then re-execute the command.
Failed to move the file. Source Filename=[SRCFILE], Target Filename=[DSTFILE]
Explanation
The file could not be moved.
Parameters
SRCFILE : Source file for moving
DSTFILE : Destination file for moving
System action
The system terminates processing.
System administrator response
Check for the presence of the directory, the access permission, the free disk space, and then re-execute the command.
Failed to create a link. Source Path=[SRCPATH], Target Path=[DSTPATH]
Explanation
The link could not be created.
Parameters
SRCPATH : Link source
DSTPATH : Link target
System action
The system terminates processing.
System administrator response
Check for the presence of the directory, the access permission, the free disk space, and then re-execute the command.
The command could not be called or the command failed. Command Line=[COMMAND]
Explanation
The command could not be executed or command failed.
Parameters
COMMAND : Command line
System action
The system terminates processing.
System administrator response
Check for the presence of the command indicated in COMMAND parameter.
If COMMAND parameter is the smcvtenv command, collect the following file, and then contact a Fujitsu systems engineer.
[Solaris, Linux, and HP-UX versions]
/var/opt/FJSVswssc/log/swclsetup.log
[Windows version]
"Work directory"\var\security\log\swclsetup.log
Usage : swtgclset_hacmp -k NodeType -m MountPoint [-n NodeName -s Service]
Explanation
An invalid option was specified.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
For the primary node, specify a node name, service name.
Explanation
For the primary node, specify a node name, service name.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
High Availability Cluster Multi-Processing has not been installed.
Explanation
High Availability Cluster Multi-Processing has not been installed.
System action
The system terminates processing.
System administrator response
Check the environment of High Availability Cluster Multi-Processing.
Usage : stgclunset_hacmp -n NodeName [-f]
Explanation
An invalid option was specified.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
Failed to create the AdvancedCopy Manager application. Error Code = [CODE1]-[CODE2]
Explanation
It failed to make the AdvancedCopy Manager application.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
For the secondary node, it can not be specified except for node type and mount point.
Explanation
For the secondary node, it can not be specified except for node type and mount point.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
Failed to delete the AdvancedCopy Manager application. Error Code = [CODE1]-[CODE2]
Explanation
It failed to delete the AdvancedCopy Manager application.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Usage : stgclset_aixvcs -k NodeType -m MountPoint [ -n NodeName -s Service]
Explanation
An invalid option was specified.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
For the primary node, specify a node name, service name.
Explanation
For the primary node, specify a node name, service name.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
VERITAS Cluster Server has not been installed.
Explanation
VERITAS Cluster Server has not been installed.
System action
The system terminates processing.
System administrator response
Check the environment of VERITAS Cluster Server.
Usage: stgclunset_aixvcs -n NodeName [-f]
Explanation
An invalid option was specified.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
Failed to create the AdvancedCopy Manager application. Error Code = [CODE1]-[CODE2]
Explanation
It failed to make the AdvancedCopy Manager application.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
For the secondary node, it can not be specified except for node type and mount point.
Explanation
For the secondary node, it can not be specified except for node type and mount point.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
Failed to delete the AdvancedCopy Manager application. Error Code = [CODE1]-[CODE2]
Explanation
It failed to delete the AdvancedCopy Manager application.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Usage : stgclset_hpvcs -k NodeType -m MountPoint [ -n NodeName -s Service]
Explanation
An invalid option was specified.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
For the primary node, specify a node name, service name.
Explanation
For the primary node, specify a node name, service name.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
VERITAS Cluster Server has not been installed.
Explanation
VERITAS Cluster Server has not been installed.
System action
The system terminates processing.
System administrator response
Check the environment of VERITAS Cluster Server.
Usage: stgclunset_hpvcs -n NodeName [-f]
Explanation
An invalid option was specified.
System action
The system terminates processing.
System administrator response
After checking the command, re-execute processing.
Failed to create the AdvancedCopy Manager application. Error Code = [CODE1]-[CODE2]
Explanation
It failed to make the AdvancedCopy Manager application.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
For the secondary node, it can not be specified except for node type and mount point.
Explanation
Only node type and mount point can be specified for the secondary node.
System action
The system terminates processing.
System administrator response
Check that the command syntax is complete with all the required parameters, and then re-execute.
Failed to delete the AdvancedCopy Manager application. Error Code = [CODE1]-[CODE2]
Explanation
It failed to delete the AdvancedCopy Manager application.
Parameters
CODE1 : Error code 1
CODE2 : Error code 2
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
