Top
ETERNUS SF Express V14.2 User's Guide

A.7 Host Interface Information

Express specifies the following information as host interface information.

Note

When the host response of the same name has already been registered in ETERNUS disk storage system, Express does not re-register it.

Point

For the information that is not described following, specify it using the ETERNUS Web GUI.

Table A.8 Host interface configuration information (For FC connection)

Item

Description

Connection

Select the topology of a target port from "Fabric" or "FC-AL".
It is necessary to allocate loop ID to the target port for "FC-AL".

Set Loop ID

When "FC-AL" is selected, set this item.
Select either from "Manual" or "Auto".

Loop ID

When "FC-AL" is selected, set this item.
If "Auto" is selected in "Set Loop ID", "Ascending" is automatically specified.
If "Manual" is selected in "Set Loop ID", enter loop ID in hexadecimal.
The input range is between 0x00 and 0x7D in hexadecimal.

Transfer Rate (Gbit/s)

Specify the transfer rate of the target port as follows.

  • 4Gbit/s Model

    • Automatically

    • 1

    • 2

    • 4

  • 8Gbit/s Model

    • Automatically

    • 2

    • 4

    • 8

Host Affinity

For host affinity of the target port, select "enable" or "disable".

Host Response

When "disable" is selected for Host Affinity, select a host response specified for the target port.

  • 0:Default (ETERNUS DX60/DX80/DX90)

  • 0:Others (ETERNUS DX80 S2/DX90 S2)

    Initial value.

  • windowsmsdsm

    Recommended value to connect to the Windows host in which Microsoft Device Specific Module (DSM) is installed.

  • linuxdevmap

    Recommended value to connect the Linux host in which device-mapper-multipath is installed.

  • SolarisMPxIO

    Recommended value to connect to the Solaris host in which MPxIO is installed.

  • ESX4

    Recommended value to connect to the VMware host in which VMware vSphere 4 (ESX 4.0) is installed.

  • ESX35

    Recommended value to connect to the VMware host in which VMware Infrastructure 3 (ESX 3.5 or ESXi 3.5) is installed.

  • EgeneraPAN

    Recommended value to connect to the Egenera host in which PAN manager is installed.


Table A.9 Host interface configuration information (For iSCSI connection)

Item

Description

IP Address

IP address of a target port. The specifiable value is 0.0.0.0 to 255.255.255.255.

Subnet Mask

Subnet mask of a target port. The specifiable value is 0.0.0.0 to 255.255.255.255.

Default Gateway

IP address of a default gateway. The specifiable value is 0.0.0.0 to 255.255.255.255.

iSCSI Name

Input the iSCSI name of a target port in 1 to 233 one-byte alphanumeric characters and symbols (hyphen (-), colon (:), period (.)).

Alias Name

Input the alias name of a target port in 1 to 31 one-byte alphanumeric characters, symbols and spaces.
An iSCSI name is an official name to specify a target iSCSI port while an alias name is used as a nickname.

Host Affinity

For host affinity of the target port, select "enable" or "disable".

Host Response

When "disable" is selected for Host Affinity, select a host response specified for the target port.

  • 0:Default (ETERNUS DX60/DX80/DX90)

  • 0:Others (ETERNUS DX80 S2/DX90 S2)

    Initial value.

  • windowsmsdsm

    Recommended value to connect to the Windows host in which Microsoft Device Specific Module (DSM) is installed.

  • linuxdevmap

    Recommended value to connect the Linux host in which device-mapper-multipath is installed.

  • SolarisMPxIO

    Recommended value to connect to the Solaris host in which MPxIO is installed.

  • ESX4

    Recommended value to connect to the VMware host in which VMware vSphere 4 (ESX 4.0) is installed.

  • ESX35

    Recommended value to connect to the VMware host in which VMware Infrastructure 3 (ESX 3.5 or ESXi 3.5) is installed.

  • EgeneraPAN

    Recommended value to connect to the Egenera host in which PAN manager is installed.


Table A.10 Host interface configuration information (For SAS connection)

Item

Description

Host Affinity

For host affinity of the target port, select "enable" or "disable".

Host Response

When "disable" is selected for Host Affinity, host response specified for the target port.

  • 0:Default (ETERNUS DX60/DX80/DX90)

  • 0:Others (ETERNUS DX80 S2/DX90 S2)