Registration of a hardware provider went wrong.
Explanation
Hardware provider registration failed.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
An hardware provider is registered.
Explanation
The hardware provider has already been registered.
System action
The system terminates processing.
System administrator response
No response is required.
Deletion of an hardware provider went wrong.
Explanation
Hardware provider deletion failed.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
An hardware provider is deletion ending.
Explanation
The hardware provider has already been registered.
System action
The system terminates processing.
System administrator response
No response is required.
Internal inconsistency occurred. Server=[SERVER]
Explanation
An internal inconsistency occurred.
Parameters
SERVER : Server name
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Cannot acquire server information.
Explanation
Server information could not be obtained.
System action
The system terminates processing.
System administrator response
When the cluster operation is running, check whether the server is a node running in a cluster operation.
Information acquisition went wrong from the repository. Error code=[ERRNO]
Explanation
Information could not be obtained from the repository.
Parameters
ERRNO : Error code
System action
The system terminates processing.
System administrator response
Refer to "B.2 Error Codes for Configuration Management", take action according to the instructions for the error code, and re-execute processing.
The server is not registered. Server=[SERVER]
Explanation
The server is not registered.
Parameters
SERVER : Server name
System action
The system terminates processing.
System administrator response
Check the server registration status.
The device is not registered. Device=[DEVICE]
Explanation
The device is not registered.
Parameters
DEVICE : Device name
System action
The system terminates processing.
System administrator response
Check the device registration status.
A device is registered as copy set information. Device=[DEVICE], server=[SERVER]
Explanation
The device is already registered as copyset information.
Parameters
DEVICE : Device name
SERVER : Server name
System action
The system terminates processing.
System administrator response
Use the reference option of the copyset registration, deletion, or reference command to check the device registration status.
Cannot acquire device information. Server=[SERVER], error=[ERROR]
Explanation
Device information could not be obtained.
Parameters
SERVER : Server name
ERROR : Detailed error message for ETERNUS disk storage system
System action
The system terminates processing.
System administrator response
Refer to "Appendix A Detail Error Messages of ETERNUS/GR Series", take action according to the instructions for the error code, and re-execute processing.
The error occurred in processing between servers. Error code=[ERROR], detailed code=[DETAIL]
Explanation
An error occurred during processing between servers.
Parameters
ERROR : Error code
DETAIL : Detailed code
System action
The system terminates processing.
System administrator response
Refer to "B.1 Error Codes for Communication Service/Communication daemon", take action according to the instructions for the error code, and re-execute processing. "Request send destination server" is the copy target server.
Access of copy set information went wrong. Server=[SERVER]
Explanation
Access to the copyset information failed.
Parameters
SERVER : Server name
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Fault is in the size of a device. Copied material device=[SIZE1], copy place device=[SIZE2]
Explanation
The device size is invalid.
Parameters
SIZE1 : Source device size (blocks) for copying
SIZE2 : Destination device size (blocks) for copying
System action
The system terminates processing.
System administrator response
Check the device size.
The device is not registered as copy set information. Device=[DEVICE]
Explanation
The device is not registered as copyset information.
Parameters
DEVICE : Device name
System action
The system terminates processing.
System administrator response
Check the device registration status.
The server of cluster employment cannot be made into a copy place server.
Explanation
A server used for the cluster operation cannot be specified as a copy target server.
System action
The system terminates processing.
System administrator response
Confirm the copy target server.
The same server was specified at the copy place the copied material. Or the same LUN was specified at the copy place the copied material.
Explanation
The same server was specified as the copy source and target server, or the same LUN was specified as the copy source and target LUN.
System action
The system terminates processing.
System administrator response
Check the server and LUN.
The group name format is different.
Explanation
The group name format is different.
System action
The system terminates processing.
System administrator response
Check the group name.
The copy type differs from the copy set information that has been registered.
Explanation
The copy type does not match the copy set information that has already been registered.
System action
The system terminates processing.
System administrator response
Check the copy type.
The group name has already been registered.
Explanation
The group name has already been registered.
System action
The system terminates processing.
System administrator response
Check the group name.
Specify the target device.
Explanation
Specify the target device.
System action
The system terminates processing.
System administrator response
Execute the command with copy destination information specified.
The session exists.
Explanation
The session already exists.
System action
The system terminates processing.
System administrator response
Delete the session, and execute copy set deletion processing.
It failed in the acquisition of the disk type.
Explanation
The disk type fetch process failed.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
The copy origin and the disk type at the copy destination are different. Copy origin = [SRCTYPE], Copy destination = [DSTTYPE]
Explanation
The copy source and copy destination are different disk types.
Parameters
SRCTYPE : Source disk type for copying
DSTTYPE : Destination disk type for copying
System action
The system terminates processing.
System administrator response
Check the copy source disk and copy destination disk types and make then the same type.
Internal inconsistency occurred.
Explanation
An internal inconsistency occurred.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Acquisition of device information went wrong. Error=[ERROR]
Explanation
Device information could not be obtained.
Parameters
ERROR : Detailed error message of the ETERNUS disk storage system
System action
The system terminates processing.
System administrator response
Refer to "Appendix A Detail Error Messages of ETERNUS/GR Series", take action according to the instructions for the error code, and re-execute processing.
Access of copy set information went wrong.
Explanation
Access to copyset information failed.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting on the target server, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Acquisition of server information went wrong.
Explanation
Server information could not be obtained.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting on the target server, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Copy set information is not registered.
Explanation
Copyset information is not registered.
System action
The system terminates processing.
System administrator response
Check the registration status of the target device.
An attempt to obtain physical disk information failed.
Explanation
An attempt to obtain physical disk information failed.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting on the target server, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
The server has not been registered. Server = [SERVER].
Explanation
The server has not been registered.
Parameters
SERVER : Server name
System action
The system terminates processing.
System administrator response
Check the registration status of the server.
There is not enough memory.
Explanation
There is not enough memory.
System action
The system terminates processing.
System administrator response
Terminate all other applications, and then re-execute.
Internal inconsistency occurred.
Explanation
An internal inconsistency occurred.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Insufficient memory occurred.
Explanation
A memory shortage occurred.
System action
The system terminates processing.
System administrator response
Terminate all other applications and then re-execute.
Acquisition of device information went wrong. Error=[ERROR]
Explanation
Device information could not be obtained.
Parameters
ERROR : Detailed error message of the ETERNUS disk storage system
System action
The system terminates processing.
System administrator response
Refer to "Appendix A Detail Error Messages of ETERNUS/GR Series", take action according to the instructions for the error code, and re-execute processing.
Access of a device went wrong. Error code=[ERRNO]
Explanation
Device access failed.
Parameters
ERRNO : Error code
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting on the target server, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
It is copy set a non-registered device. Signature=[SIGNATURE], disk=[DISK]
Explanation
Device is not registered for copy set.
Parameters
SIGNATURE : Disk signature
DISK : Physical disk number
System action
The system terminates processing.
System administrator response
Check the device registration status.
Access of copy set information went wrong.
Explanation
Access to copyset information failed.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting on the target server, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
OPC cannot be performed. Error=[ERROR]
Explanation
OPC cannot be executed.
Parameters
ERROR : Detailed error message of ETERNUS disk storage system
System action
The system terminates processing.
System administrator response
Refer to "Appendix A Detail Error Messages of ETERNUS/GR Series", take action according to the instructions for the error code, and re-execute processing.
If 24 (hardware error requiring CE-CALL) is output as ERROR parameter, Advanced Copy was probably not set correctly. Check the GR series setting.
It is execution from other than ACM requestor.
Explanation
Execution must be performed from the ACM requester.
System action
The system terminates processing.
System administrator response
Check whether the ACM requester is executed.
The session status is invalid.
Explanation
The session status is invalid.
System action
The system terminates processing.
System administrator response
Check the copy status.
The suspend of EC cannot be performed. Error=[ERROR]
Explanation
The suspend of EC cannot be performed.
Parameters
ERROR : Detailed error message for the ETERNUS disk storage system
System action
The system terminates processing.
System administrator response
Refer to "Appendix A Detail Error Messages of ETERNUS/GR Series", take action according to the instructions for the error code, and re-execute processing.
If 24 (hardware error requiring CE-CALL) is output as ERROR parameter, Advanced Copy was probably not set correctly. Check the GR series setting.
An attempt to obtain session information failed. Error=[ERROR]
Explanation
An attempt to obtain session information failed.
Parameters
ERROR : Detailed error message for the ETERNUS disk storage system
System action
The system terminates processing.
System administrator response
Refer to "Appendix A Detail Error Messages of ETERNUS/GR Series", take action according to the instructions for the error code, and re-execute processing.
If 24 (hardware error requiring CE-CALL) is output as ERROR parameter, Advanced Copy was probably not set correctly. Check the GR series setting.
QuickOPC cannot be executed. Error=[ERROR]
Explanation
QuickOPC cannot be executed.
Parameters
ERROR : Detailed error message for the ETERNUS disk storage system
System action
The system terminates processing.
System administrator response
Refer to "Appendix A Detail Error Messages of ETERNUS/GR Series", take action according to the instructions for the error code, and re-execute processing.
If 24 (hardware error requiring CE-CALL) is output as ERROR parameter, Advanced Copy was probably not set correctly. Check the GR series setting.
It is copy set a non-registered device. DiskID = [ID], disk = [DISK]
Explanation
The device is not registered as copy set information.
Parameters
ID : Disk ID
DISK : Physical disk number
System action
The system terminates processing.
System administrator response
Check the registration status of the device.
An internal conflict has occurred.
Explanation
An internal conflict has occurred.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
There is not enough memory.
Explanation
There is not enough memory.
System action
The system terminates processing.
System administrator response
Terminate all other applications, and then re-execute.
The device has not been registered for EC use in the copy set information.
Explanation
The device has not been registered for EC use in the copy set information.
System action
The system terminates processing.
System administrator response
Check the content registered for the copy set.
An attempt to obtain device information failed.
Explanation
An attempt to obtain device information failed.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
An attempt to obtain server information failed.
Explanation
An attempt to obtain server information failed.
System action
The system terminates processing.
System administrator response
When the cluster operation is running, check whether the server is a node running in a cluster operation.
Access to copy set information failed. Server = [SERVER]
Explanation
Access to copy set information failed.
Parameters
SERVER : Server name
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting on the target server, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
The device is not registered as copy set information. Device=[DEVICE], Server = [SERVER]
Explanation
The device is not registered as copy set information.
Parameters
DEVICE : Device name
SERVER : Server name
System action
The system terminates processing.
System administrator response
Check the registration status of the device.
The server has not been registered. Server = [SERVER].
Explanation
The server has not been registered.
Parameters
SERVER : Server name
System action
The system terminates processing.
System administrator response
Check the registration status of the server.
An attempt to obtain physical disk information failed.
Explanation
An attempt to obtain physical disk information failed.
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting on the target server, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
Operation failed. Error=[ERROR]
Explanation
An OPC, EC or QuickOPC operation failed.
Parameters
ERROR : Detailed error message for the ETERNUS disk storage system
System action
The system terminates processing.
System administrator response
Refer to "Appendix A Detail Error Messages of ETERNUS/GR Series", take action according to the instructions for the error code, and re-execute processing.
If 24 (hardware error requiring CE-CALL) is output as ERROR parameter, Advanced Copy was probably not set correctly. Check the GR series setting.
Copy has not started.
Explanation
OPC, EC or QuickOPC has not started.
System action
The system terminates processing.
System administrator response
Check the copy status.
The operation cannot be performed with the current copy status.
Explanation
The operation cannot be performed with the current copy status.
System action
The system terminates processing.
System administrator response
Check the copy status.
If necessary, forcibly stop or pause the operation.
For OPC and QuickOPC, only stop operations are possible.
Explanation
For OPC and QuickOPC, only stop operations are possible.
System action
The system terminates processing.
System administrator response
Check the parameters.
It failed in the change in prov_copyset.ini.Execution server = [SERVER]
Explanation
The copy set change failed.
Parameters
SERVER : Execution server name
System action
The system terminates processing.
System administrator response
Refer to the following manual and collect the information required for troubleshooting, and then contact a Fujitsu systems engineer.
"Collecting maintenance information" in the "ETERNUS SF AdvancedCopy Manager Operator's Guide"
The server for the change doesn't exist. Object server = [SERVER]
Explanation
The server name specified to be changed does not exist.
Parameters
SERVER : Target server name
System action
The system terminates processing.
System administrator response
Check the name of the server to be changed.
Cannot aquire server information.
Explanation
The server information fetch process failed.
System action
The system terminates processing.
System administrator response
For cluster operation, check that the execution machine is a currently operating node.
The server is not registered. Server = [SERVER]
Explanation
The server is not registered.
Parameters
SERVER : Server name
System action
The system terminates processing.
System administrator response
Check the registration status of the server.
Information acquisition went wrong from the repository. Error code = [ERRNO]
Explanation
The process to fetch information from the repository failed.
Parameters
ERRNO : Error code
System action
The system terminates processing.
System administrator response
Refer to "B.2 Error Codes for Configuration Management", take action according to the instructions for the error code, and re-execute processing.