11.4.13 tbogetoluinfo (ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000 information acquisition command)

NAME

tbogetoluinfo - Acquisition of information on ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000

SYNOPSIS

/opt/FJSVswstm/bin/tbogetoluinfo -l ETERNUSIPaddress [ETERNUSIPaddress ...]

DESCRIPTION

This command obtains the information required for backing up the data of an ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000 disk to tape in a multi-path environment. The command obtains this information from the ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000.

This command must be executed when the following occur:

Initial installation of a Tape Server
Upgrading of the Tape Server
Upgrading of the Tape Server operating system
Changing the RAID configuration (RAID Group configuration and LUNV configuration) of ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000
Addition of a new ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000

OPTIONS

-l

Specifies that ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000 information be obtained from the ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000 specified by ETERNUSIPaddress via a LAN

This option cannot be omitted.

OPERANDS

ETERNUSIPaddress: Specifies the IP address of the ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000 from which information is to be obtained. The only applicable IP addresses are "IPv4."

EXIT STATUS

=0: Completed successfully

>0: Terminated abnormally

EXAMPLES

Obtain information from the ETERNUS4000 specified by ETERNUSIPaddress (200.30.40.30).

# /opt/FJSVswstm/bin/tbogetoluinfo -l 200.30.40.30
200.30.40.30 completed. [total olu = 100]
The configuration file of CM information was update.
#

The following message is posted if the Tape Server is upgraded from ACM13.1 or earlier to ACM13.2 or later and 11.4.14 tboactmplbext (Tape Server upgrade settings command) is executed:
```
# /opt/FJSVswstm/bin/tbogetoluinfo -l 200.30.40.30
200.30.40.30 completed. [total olu = 100]
/var/opt/FJSVmplb/mplb_ext.conf was update.
#
```

NOTES

If this command was executed in an environment where the GR multi-path driver is installed, also execute the command below. However, do not execute the command while the RAID device is processing the migration. This command need not be executed in the ETERNUS multi-path driver is installed.
```
# mplbconfig -q
#
```
To execute this command, the following conditions must be satisfied:
- The ETERNUS3000 firmware version is the following or later:
  Model
  Firmware version
  M100/M200/M400/M600
  V20L32
  M300/M500/M700
  V10L10
- For ETERNUS DX60/DX80/ETERNUS2000/ETERNUS4000, execute this command regardless of the firmware version.
- The Tape Server and the ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000 are connected to a LAN.
- The Tape Server and the ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000 are FC-connected.
- An ETERNUS multi-path driver or a GR multi-path driver is installed on the Tape Server.
- 11.4.1 tbochkconf (Tape Server definition file check command) has been executed with the ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000 access path written in the /etc/opt/FJSVswstm/conf/devpath.conf file.
- The command is not used in a configuration without the ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000.
- If an IP address of a device other than the ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000 is specified, no information is obtained.
- After the ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000 RAID configuration is changed (including LUNV additions and deletions) or a new ETERNUS DX60/DX80/ETERNUS2000/ETERNUS3000/ETERNUS4000 is added, backup to tape or restoration from tape fails unless this command has been executed.
- /var/opt/FJSVmplb/mplb_ext.conf is a file in which the GR multi-path driver is set. Do not edit the file manually because it affects multi-path driver operation.
- If this command is executed and 11.4.14 tboactmplbext (Tape Server upgrade settings command) was not executed during an upgrade, information collection fails in a configuration that does not have two access paths set for each CM.
- Note that, if 11.4.14 tboactmplbext (Tape Server upgrade settings command) has been executed, the /etc/opt/FJSVswstm/conf/mplb_ext_active file exists. Execute the following command to check if this file exists:
```
# ls -l /etc/opt/FJSVswstm/conf/mplb_ext_active
```

Model	Firmware version
M100/M200/M400/M600	V20L32
M300/M500/M700	V10L10