The general verification function checks the configuration of the device unit displayed on the design window for problems.
To start general verification, select [Design]-[Verification All] from the menu or click the general verification icon on the toolbar.
The table below provides a summary of what items are checked and what messages are output as the result of checking. Note that device setup is possible even if a warning message with a message number of the type 4xxxxx has been displayed.
Checking | Message No. | Message text |
|---|---|---|
When disks are mounted on the ETERNUS3000, check whether disks are mounted in ascending order of DE numbers in each loop and also in ascending order of slot numbers beginning from 0 in each DE. | 42520, 42521 | Install disks in order from slot 0, starting with the lower number DEs (loop ID:X). |
Check whether the number of disks mounted on the device satisfies the requirements. | 62531, 62532, | There are insufficient disks. There must be at least X. |
Check whether the number of disks mounted on the device satisfies the requirements. | 62531, 62533, | There are insufficient disks. There must be at least X. |
Check whether the number of disks mounted on the device satisfies the requirements. | 62552 | There are insufficient disks. Check necessary number of Disk. |
Check whether disks are mounted sequentially, without skipping any slot, from the beginning in each DE. | 42530 | Install the disks starting with the first one. |
Check whether the DEs are mounted continuously. | 42532, 42533 | The loop ID:X DEs were not installed in sequence. |
Check whether the DEs are mounted continuously. | 42534 | The DEs were not installed in sequence. |
A hot spare disk must be mounted in each loop. Check whether a hot spare disk is missing in any loop. | 42535 | One loop does not contain a hot spare disk. |
When nearline FC disks are mounted, check whether at least 12 nearline disks (except the system disk) are mounted. | 42536 | Install 12 or more disks that are not nearline FC disks. |
When nearline FC disks are mounted, check whether at least 24 nearline disks (except the system disk) are mounted. | 42537 | Install 24 or more disks that are not nearline FC disks. |
When the SAS disk is used for RAID group configuration disk, check whether the hot spare of the SAS disk is mounted. | 42538 | The hot spare of the SAS disk is not found. |
When the nearline SATA disk is used for RAID group configuration, check whether the hot spare of the nearline SATA disk is mounted. | 42539 | The hot spare of the nearline SATA disk is not found. |
When the fiber channel disk is used for RAID group configuration disk, check whether the hot spare of the fiber channel disk is mounted. | 42540 | One loop does not contain the hot spare of the fibre channel disk. |
When the nearline FC disk is used for RAID group configuration disk, check whether the hot spare of the nearline FC disk is mounted in each loop. | 42541 | One loop does not contain the hot spare of the nearline FC disk. |
When the nearline SATA disk is used for RAID group configuration disk, check whether the hot spare of the nearline SATA disk is mounted in each loop. | 42542 | One loop does not contain the hot spare of the nearline SATA disk. |
When the nearline SAS disk is used for RAID group configuration disk, check whether the hot spare of the nearline SAS disk is mounted. | 42544 | The hot spare of the nearline SAS disk is not found. |
When SSD is used by the RAID group configuration disk, check whether the SSD hot spare is mounted in each loop. (ETERNUS4000, ETERNUS8000) | 42545 | One loop does not define the SSD hot spare. |
Check whether two or more disks are mounted in each DE. | 62521 | Install the two data disks in the first slots of the DE. |
Check whether the same number of DEs are mounted in individual loops. | 62522 | The number of DEs is different in loop ID:0 and loop ID:1. |
Check whether disks are mounted in Slots 0 to 3 of DE0x00. | 62523 | Install disk between slot 0 and 3 in DE0x00. |
Check whether DEs are mounted in ascending order of the DE numbers. | 62529 | DE is not installed in sequence. |
Check whether the maximum capacity of the hot spare disk is greater than the maximum capacity of disks related to RAIDGroups. Check this for each loop. | 62530 | One of the hot spare disks is not working. |
Check whether the maximum capacity of the SAS disk defined as hot spare is greater than that of the SAS disk used in RAID Groups. | 62544 | Hot spare disk with insufficient capacity found in SAS disk. |
Check whether the maximum capacity of the nearline SATA disk defined as hot spare is greater than that of the nearline SATA disk used in RAIDGroups. | 62545 | Hot spare disk with insufficient capacity found in nearline SATA disk. |
Check for each loop whether the maximum capacity of the fibre channel disk defined as hot spare is greater than that of the fibre channel disk used in RAIDGroups. | 62547 | One loop that has hot spare disk with insufficient capacity found in fibre channel disk. |
Check for each loop whether the maximum capacity of the nearline FC disk defined as hot spare is greater than that of the nearline FC disk used in RAIDGroups. | 62548 | One loop that has hot spare disk with insufficient capacity found in nearline FC disk. |
Check for each loop whether the maximum capacity of the nearline SATA disk defined as hot spare is greater than that of the nearline SATA disk used in RAIDGroups. | 62549 | One loop that has hot spare disk with insufficient capacity found in nearline SATA disk. |
Check whether the maximum capacity of the nearline SAS disk defined as hot spare is greater than that of the nearline SAS disk used in RAID Groups. | 62554 | Hot spare disk with insufficient capacity found in nearline SAS disk. |
Check for each loop whether the maximum capacity of the SSD defined as hot spare is greater than that of the SSD used in RAIDGroups. | 62561 | One loop that defines an SSD hot spare disk with insufficient capacity found. |
