PRIMECLUSTER Installation and Administration Guide 4.2 (Linux)
Contents Index PreviousNext

Appendix D Messages> D.6 Messages Related to the Setting of the Shutdown Facility

D.6.2 Error Messages

If panicinfo_setup fails, the following messages will be output to the standard error output according to the cause.


 

ERROR: <command> failed

Content:

Execution of the <command> command failed.

Corrective action:

Check the command and execute it again.


 

ERROR: <command> failed on <node>

Content:

The <command> command failed on the <node> node.

Corrective action:

Check the command and execute the <command> command on the <node> node again.


 

ERROR: <command> timeout

Content:

Execution of the <command> command timeout.

Corrective action:

Check the command and execute the <command> command on the <node> node again.


 

ERROR: failed to distribute index file to <node>

Content:

Distribution of the index file to <node> node failed.

Corrective action:

Confirm that the CF services (CFSH, CFCP) have started normally.


 

ERROR: failed to distribute /etc/panicinfo.conf file to <node>

Content:

Distribution of the panicinfo definition file to <node> node failed.

Corrective action:

Confirm that the CF services (CFSH, CFCP) have started normally.


 

ERROR: /etc/sysconfig/netdump is invalid on <node>
ERROR: Cannot find the Netdump client's IP address for <device> on <node>

Content:

Reading of the Netdump client settings on the <node> node failed.

Corrective action:

Confirm that Netdump is normally set up.


 

WARNING: /etc/panicinfo.conf file already exists.
(I)nitialize, (C)opy or (Q)uit (I/C/Q) ?

Content:

The panicinfo configuration file already exists.

Corrective action:

Enter "I" to initialize the panicinfo configuration file, "C" to distribute the panicinfo configuration file on the command execution node, and "Q" to terminate the command.


 

ERROR: failed to change mode of index file on <node>

Content:

Changing of the index file mode on <node> node failed.

Corrective action:

Confirm that the "chmod" command can be executed normally on <node> node for the "/etc/opt/FJSVcllkcd/etc/SA_lkcd.idx" file, and then re-execute the command.


 

ERROR: failed to patch rcsd.cfg on <node>

Content:

Updating of rcsd.cfg failed on the <node> node.

Corrective action:

Confirm that the "/etc/opt/SMAW/SMAWsf/rcsd.cfg" file is included in the <node> node and then, re-execute the command.


 

ERROR: failed to change owner of index and rcsd.cfg file on <node>

Content:

Changing of the owner on the <node> node failed.

Corrective action:

Confirm that the "chown" command can be executed for the "/etc/opt/FJSVcllkcd/etc/SA_lkcd.idx" file and for the "/etc/opt/SMAW/SMAWsf/rcsd.cfg" file on the <node> node, and then re-execute the command.


 

ERROR: failed to change group of index and rcsd.cfg file on <node>

Content:

Changing of the owner group on the <node> node failed.

Corrective action:

Confirm that the "chgrp" command can be executed for the "/etc/opt/FJSVcllkcd/etc/SA_lkcd.idx" file and for the "/etc/opt/SMAW/SMAWsf/rcsd.cfg" file on the <node> node, and then re-execute the command.


 

ERROR: failed to change mode of /etc/panicinfo.conf file on <node>

Content:

Changing of the panicinfo configuration file mode on <node> node failed.

Corrective action:

Confirm that the "chmod" command can be executed normally on <node> node for the "/etc/panicinfo.conf" file, and then re-execute the command.


 

ERROR: failed to change owner of /etc/panicinfo.conf file on <node>

Content:

Changing of the owner on the <node> node failed.

Corrective action:

Confirm that the "chmod" command can be executed normally for the "/etc/panicinfo.conf" file on the <node> node, and then re-execute the command.


 

ERROR: failed to change group of /etc/panicinfo.conf file on <node>

Content:

Changing of the owner group on the <node> node failed.

Corrective action:

Confirm that the "chgrp" command can be executed normally for the "/etc/panicinfo.conf" file on the <node> node, and then re-execute the command.


 

ERROR: internal error, ...

Content:

Internal error.

Corrective action:

Copy this message, and then contact your Fujitsu systems engineer (SE).


 

ERROR: The Shutdown Facility configuration cannot be found.

Content:

The Shutdown Facility configuration file is not found. You might not have completed configuring the Shutdown Facility.

Corrective action:

Confirm that Shutdown Facility configuration is completed then execute the command again.


 

ERROR: Reading the Shutdown Facility configuration failed.

Content:

Reading Shutdown Facility configuration failed. You might have set the Shutdown Facility incorrectly.

Corrective action:

Confirm that Shutdown Facility configuration is correct then execute the command again.


 

ERROR: Reading the Shutdown Agent configuration failed.

Content:

Reading Shutdown Agent configuration failed. You might have set the Shutdown Agent incorrectly.

Corrective action:

Confirm that Shutdown Agent configuration is correct then execute the command again.


 

ERROR: <File name> generation failed.

Content:

Creation of the <file name> file failed.

Corrective action:

Confirm that the <file name> file can be created then execute the command again.


 

ERROR: The RSB Shutdown Agent configuration cannot be found.

Content:

The RSB Shutdown Agent configuration file is not found. You might not have completed configuration the RSB Shutdown Agent.

Corrective action:

Confirm that RSB Shutdown Agent configuration is completed then execute the command again.


 

ERROR: The Blade Shutdown Agent configuration cannot be found.

Content:

The Blade Shutdown Agent configuration file is not found. You might not have completed configuration the Blade Shutdown Agent.

Corrective action:

Confirm that Blade Shutdown Agent configuration is completed then execute the command again.


 

ERROR: The IPMI Shutdown Agent configuration cannot be found.

Content:

The IPMI Shutdown Agent configuration file is not found. You might not have completed configuration the IPMI Shutdown Agent.

Corrective action:

Confirm that IPMI Shutdown Agent configuration is completed then execute the command again.


Contents Index PreviousNext

All Rights Reserved, Copyright(C) FUJITSU LIMITED 2006