11.2 Restoring the PRIMECLUSTER Operation Environment

PRIMECLUSTER Installation and Administration Guide 4.1 (for Solaris(TM) Operating System)

Contents Index

Part 5 Maintenance

> Chapter 11 Backing Up and Restoring a PRIMECLUSTER System

11.2 Restoring the PRIMECLUSTER Operation Environment

Take the following steps to restore the PRIMECLUSTER operation environment:

Procedure

Boot the machine to be restored in single-user mode.

After booting the machine in single-user mode, mount the file system by executing the "mountall -l" command.

Example: Reboot in single-user mode.

# shutdown -g0 -i0 -y

...

ok boot -s

...

INIT: SINGLE USER MODE

Enter control-d to proceed with normal startup,

(or enter the root password for system maintenance):

...

# mountall -l

/dev/rdsk/c0t0d0s4: is clean.

/dev/rdsk/c0t0d0s3: is clean.

To restore the PRIMECLUSTER operation environment, execute the following command.
```
/opt/SMAW/bin/cfrestore [ -f ] [ -p ] [ -y ] [ -M ] [ n ]
```
For details on the command parameters, refer to the explanation of the cfrestore(1M) command.

Example: Restore the PRIMECLUSTER operation environment.
```
# cfrestore
```
```
08/07/02 11:17:55 cfbackup 1 started
```
```
...
```
```
08/07/02 11:21:23 cfbackup 1 ended
```
```
# 
```
Restore a single configuration file.

The restoration function does not restore backed-up files. The system files mentioned here in are provided by the operation system (environment). Restore the backed-up files manually if necessary.

Example: Pick up the "/etc/vfstab" file from the backup data "fuji2_ccbr1.tar.Z".
1. Confirm the backup data "fuji2_ccbr1.tar.Z" and then check for the backed-up system file.
```
# ls /var/spool/SMAW/SMAWccbr/*.tar.Z
```
```
fuji2_ccbr1.tar.Z
```
```
# zcat /var/spool/SMAW/SMAWccbr/fuji2_ccbr1.tar.Z | tar tvf - ./OS
```
```
drwxrwxrwx   0/1        0 Nov 20 13:58 2002 ./OS/
```
```
drwxrwxrwx   0/1        0 Nov 20 13:57 2002 ./OS/etc/
```
```
...
```
```
-rw-r--r--   0/1      909 Nov 20 13:57 2002 ./OS/etc/vfstab
```
```
...
```
```
#
```
2. Put the "/etc/vfstab" file in the "/tmp" directory.
```
# cd /tmp
```
```
# zcat /var/spool/SMAW/SMAWccbr/fuji2_ccbr1.tar.Z | tar xvf - ./OS
```
```
x ./OS, 0 bytes, 0 tape blocks
```
```
x ./OS/etc, 0 bytes, 0 tape blocks
```
```
x ./OS/etc/hosts, 401 bytes, 1 tape blocks
```
```
...
```
```
x ./OS/etc/vfstab, 909 bytes, 2 tape blocks
```
```
...
```
```
#
```
3. Restore part or all of the file contents by executing the "cp(1)" or "vi(1)" command.
  
  If an invalid correction is made to the system file, login may be disabled and the system may fail to boot.
If the AutoStartUp function of the RMS has been validated, invalidate it.
For details, see the "10 Appendix - Environment variables" in the "PRIMECLUSTER Reliant Monitor Service (RMS) with Wizard Tools Configuration and Administration Guide."
Reboot the machine.
Example: The machine is rebooted.
```
# shutdown -g0 -i6 -y
```
Activate the RMS configuration.
For details, see the "4.8 Activating the configuration" in the "PRIMECLUSTER Reliant Monitor Service (RMS) with Wizard Tools Configuration and Administration Guide."
Enable the AutoStartup function if it is disenabled.
For details, see the "10 Appendix - Environment variables" in the "PRIMECLUSTER Reliant Monitor Service (RMS) with Wizard Tools Configuration and Administration Guide."
Start up the RMS.
For details, see the "5.4.1 Starting RMS" in the "PRIMECLUSTER Reliant Monitor Service (RMS) with Wizard Tools Configuration and Administration Guide."

Contents Index