PRIMECLUSTER Installation and Administration Guide 4.1 (for Solaris(TM) Operating System)

7.1.2.2 Detailed Resource Information

This section describes the resource attributes that are defined in the CRM main window.

Detailed resource information

Icon/ resource class name	Attributes	Meaning/attribute value (Top: Meaning, Bottom: Attribute value)
Node	NodeID	Node identifier number.
		Node identifier number (0 to 127).
SH_SWLine	lsu_mask	Mask information for the LSU used by the line switching unit
		Logical sum of the mask information for the LSU used by the line switching unit LSU machine information LSU00 0x0001 LSU01 0x0002 LSU02 0x0004 ... LSU14 0x4000 LSU15 0x8000
SH_SWU	lsu_num	Number of switchover units installed in the line switching unit
		4, 16
	addr	RCI device address of the line switching unit
		RCI device address
SWLine	Port	Port number of the LSU (group) used by the line switching unit
		0, 1
DISK	Disk_Attr	This item indicates the physical connection mode and usage mode of a disk that can be used from the cluster system.
		LOCAL Local disk that can be accessed only from one node SHD_DISK The disk is physically shared, but the usage mode (shared disk or switchover disk) is not specified. SHD_SHARE Shared disk that can be accessed from multiple nodes SHD_SWITCH Switching disk that is used exclusively between two nodes Blank The disk connection or usage mode is not set up.
MPDisk	Disk_Attr	This item indicates the physical connection mode and usage mode of a disk that can be used from the cluster system
		LOCAL Local disk that can be accessed only from one node SHD_DISK The disk is physically shared, but the usage mode (shared disk or switchover disk) is not specified. SHD_SHARE Shared disk that can be accessed from multiple nodes SHD_SWITCH Switching disk that is used exclusively between two nodes Blank The disk connection or usage mode is not set up.
	path_stat	This item indicates the stage of each path of a multipath disk.
		The state value of each path in the multipath disk is indicated in sequence for up to eight paths starting from path 0. The values are shown with the format below. (The values in parenthesis are used when there are five or more paths.) active (A) Active standby (B) Standby discon (D) Low-order driver is disconnected. fail (F) Failed stop (S) Stopped because a path from another node to the same controller is faulted or is undergoing maintenance
SHD_DISK, SHD_MPDisk	Disk_Attr	This item indicates the physical connection mode and usage mode of a disk that can be used from the cluster system.
		SHD_DISK The disk is physically shared, but the usage mode (shared disk or switchover disk) is not specified. SHD_SHARE Shared disk that can be accessed from multiple nodes SHD_SWITCH Switching disk that is used exclusively between two nodes
SDX_DC, SDX_SHDDC	Disk_Attr	This class indicates the physical connection mode and usage mode of a GDS-managed disk class that can be used from the cluster system.
		SHD_DISK The disk is physically shared, but the usage mode (shared disk or switchover disk) is not specified. SHD_SHARE Shared disk class that allows access from multiple nodes SHD_SWITCH Switching disk class for exclusive use between two nodes
Ethernet	node_name	This item indicates the name of the node in which this LAN board is set.
		The node name is set.
	org_mac	This item indicates the MAC address that the operating system has assigned to this LAN board.
		The MAC address is in the format 00:11:22:33:44:55.
	WebView	This item indicates internal information used in the cluster.
		Undefined
SHD_Host	ip_addr	This item indicates the takeover IP address.
		The takeover IP address information is set in the format XXX.XXX.XXX.XXX. If IP address takeover has not been set, this item is blank.
	mac_addr	This item indicates the takeover MAC address.
		The takeover MAC address information is set in the format 00:11:22:33:44:55. If MAC address takeover has not been set, this item is blank.
	node_name	This item indicates the takeover node name.
		The takeover node name is set. If node name takeover has not been set, this item is blank.
	LanDev_Rid	If a takeover MAC address is used, this item indicates the resource ID of LanDev (maintenance information for customer support representative).
		If a takeover MAC address is used, the resource ID of LanDev is set.